A Simple, Single-measurement Methodology to Account for Electrode Polarization in the Dielectric Spectra of Colloidal Dispersions

2012 ◽  
Vol 41 (10) ◽  
pp. 1116-1118 ◽  
Author(s):  
Peter J. Beltramo ◽  
Eric M. Furst
Keyword(s):  
Colloidal Dispersions ◽  
Electrode Polarization ◽  
Single Measurement ◽  
Dielectric Spectra ◽  
Measurement Methodology

Single measurement of hemoglobin predicts outcome of HCC patients

2014 ◽  
Vol 52 (01) ◽  
Author(s):  
F Finkelmeier ◽  
D Bettinger ◽  
V Köberle ◽  
M Schultheiß ◽  
B Kronenberger ◽  
...  
Keyword(s):  
Single Measurement

Reliability of a Single β-Thromboglobulin Measurement in a Diabetic Population : Importance of PGE1 in Anticoagulant Mixture

1987 ◽  
Vol 57 (02) ◽  
pp. 201-204 ◽  
Author(s):  
P Y Scarabin ◽  
L Strain ◽  
C A Ludlam ◽  
J Jones ◽  
E M Kohner
Keyword(s):  
In Vitro Release ◽  
Mean Value ◽  
Reliable Estimate ◽  
Diabetic Patients ◽  
Single Measurement ◽  
Diabetic Population ◽  
The Difference ◽  
Vitro Release

SummaryDuring the collection of samples for plasma β-thromboglobulin (β-TG) determination, it is well established that artificially high values can be observed due to in-vitro release. To estimate the reliability of a single β-TG measurement, blood samples were collected simultaneously from both arms on two separate occasions in 56 diabetic patients selected for a clinical trial. From each arm, blood was taken into two tubes containing an anticoagulant mixture with (tube A) and without (tube B) PGE!. The overall mean value of B-TG in tube B was 1.14 times higher than in tube A (p <0.01). The markedly large between-arms variation accounted for the most part of within-subject variation in both tubes and was significantly greater in tube B than in tube A. Based on the difference between B-TG values from both arms, the number of subjects with artifically high B-TG values was significantly higher in tube B than in tube A on each occasion (overall rate: 28% and 14% respectively). Estimate of between-occasions variation showed that B-TG levels were relatively stable for each subject between two occasions in each tube. It is concluded that the use of PGEi decreases falsely high B-TG levels, but a single measurement of B-TG does not provide a reliable estimate of the true B-TG value in vivo.

Optical analysis of ink and other contaminants in process waters

TAPPI Journal ◽  
2012 ◽  
Vol 11 (8) ◽  
pp. 51-58
Author(s):  
ANTTI HAAPALA ◽  
MIKA KÖRKKÖ ◽  
ELISA KOIVURANTA ◽  
JOUKO NIINIMÄKI
Keyword(s):  
Optically Active ◽  
Process Water ◽  
Paper Machine ◽  
Optical Analysis ◽  
Direct Process ◽  
Active Components ◽  
Water Contaminants ◽  
Dependent Measurement ◽  
Measurement Methodology

Analysis methods developed specifically to determine the presence of ink and other optically active components in paper machine white waters or other process effluents are not available. It is generally more interest¬ing to quantify the effect of circulation water contaminants on end products. This study compares optical techniques to quantify the dirt in process water by two methods for test media preparation and measurement: direct process water filtration on a membrane foil and low-grammage sheet formation. The results show that ink content values obtained from various analyses cannot be directly compared because of fundamental issues involving test media preparation and the varied methodologies used to formulate the results, which may be based on different sets of assumptions. The use of brightness, luminosity, and reflectance and the role of scattering measurements as a part of ink content analysis are discussed, along with fine materials retention and measurement media selection. The study concludes with practical tips for case-dependent measurement methodology selection.

Automation of selected brazes' dynamic properties in high-temperatures' measurement process

2013 ◽  
Vol 18 (2-3) ◽  
pp. 33-41
Author(s):  
Dominik Sankowski ◽  
Marcin Bakala ◽  
Rafał Wojciechowski
Keyword(s):  
Surface Tension ◽  
High Temperatures ◽  
Dynamic Properties ◽  
Automatic Measurement ◽  
Measurement Methodology ◽  
Joining Process ◽  
Wetting Force ◽  
Research Grant

Abstract The good quality of several manufactured components frequently depends on solidliquid interactions existing during processing. Nowadays, the research in material engineering focuses also on modern, automatic measurement methods of joining process properties, i.a. wetting force and surface tension, which allows for quantitative determination of above mentioned parameters. In the paper, the brazes’ dynamic properties in high-temperatures’ measurement methodology and the stand for automatic determination of braze’s properties, constructed and implmented within the research grant nr KBN N N519 441 839 - An integrated platform for automatic measurement of wettability and surface tension of solders at high temperatures, are widely described

Sign in / Sign up

Export Citation Format

Share Document