Multilegged walker design—the joint torque versus workspace compromise

Author(s):  
D Howard ◽  
S J Zhang ◽  
D J Sanger ◽  
S Miao

A machine's weight is directly related to the strength of the installed joint actuators, and it is reasonable to assume that minimizing the installed joint torques will minimize the machine weight. Unfortunately, the workspace area will also reduce with the installed joint torques; thus there must be a compromise between weight (joint strength) and workspace. Methods are presented to generate the set of static workspaces corresponding to a range of installed joint torques. In this way the relationship between the workspace area and installed joint torque can be established. A numerical example is presented which shows that a small reduction in the workspace area can lead to a substantial reduction in installed joint torque and hence machine weight.

Robotica ◽  
2010 ◽  
Vol 29 (4) ◽  
pp. 581-584 ◽  
Author(s):  
Jaeheung Park

SUMMARYThe generalized Jacobian matrix was introduced for dealing with end-effector control in space robots. One of the applications of this Jacobian is to be used in Jacobian transpose control to generate joint torques given end-effector position error. It would be misleading, however, to consider the transpose of this Jacobian as a mapping from end-effector force/moment to controlled joint torques for underactuated systems or floating base robots. This paper explains why it does not represent the mapping and provides a simple example. Later, the correct mapping is provided using the dynamically consistent Jacobian inverse and then a method to compute the actuated-joint torques is explained given the desired end-effector force. Finally, the effect of using the generalized Jacobian in the Jacobian transpose control is analyzed.


2016 ◽  
Vol 138 (11) ◽  
Author(s):  
Anne Schmitz ◽  
Jaclyn Norberg

The purpose of this study was to evaluate the relationship between forceplate inaccuracies and joint torques during running. Instrumented gait analysis data were collected on a single subject running above ground. A Monte Carlo analysis was performed using 60 simulations. In each simulation, joint torques were computed as the ground reaction force (GRF) data were perturbed. Errors in joint torques were larger for proximal joints compared to the distal joints. These errors in joint torques were due more to inaccuracies in the GRF magnitude than the center of pressure (COP) measurements. Clinically, these results may be used to determine a priori the forceplate accuracy needed to measure a desired difference in joint torque between patient populations.


PLoS ONE ◽  
2020 ◽  
Vol 15 (12) ◽  
pp. e0243798
Author(s):  
Jeongryul Kim ◽  
Hongmin Kim ◽  
Jaeheung Park ◽  
Hwa Soo Kim ◽  
TaeWon Seo

Lizards run quickly and stably in a bipedal gait, with their bodies exhibiting a lateral S-shaped undulation. We investigate the relationship between a lizard’s bipedal running and its body movement with the help of a dynamic simulation. In this study, a dynamic theoretical model of lizard is assumed as a three-link consisting of an anterior and posterior bodies, and a tail, with morphometrics based on Callisaurus draconoides. When a lizard runs straight in a stable bipedal gait, its pelvic rotation is periodically synchronized with its gait. This study shows that the S-shaped body undulation with the yaw motion is generated by minimizing the square of joint torque. Furthermore, we performed the biomechanical simulation to figure out the relationship between the lizard’s lateral body undulation and the bipedal running locomotion. In the biomechanical simulation, all joint torques significantly vary by the waist and tail’ motions at the same locomotion. Besides, when the waist and tail joint angles increase, the stride length and duration of the model also increase, and the stride frequency decreases at the same running speed. It means that the lizard’s undulatory body movements increase its stride and help it run faster. In this study, we found the benefits of the lizard’s undulatory body movement and figured out the relationship between the body movement and the locomotion by analyzing the dynamics. In the future works, we will analyze body movements under different environments with various simulators.


Biomechanics ◽  
2021 ◽  
Vol 1 (1) ◽  
pp. 102-117
Author(s):  
Nasser Rezzoug ◽  
Vincent Hernandez ◽  
Philippe Gorce

A force capacity evaluation for a given posture may provide better understanding of human motor abilities for applications in sport sciences, rehabilitation and ergonomics. From data on posture and maximum isometric joint torques, the upper-limb force feasible set of the hand was predicted by four models called force ellipsoid, scaled force ellipsoid, force polytope and scaled force polytope, which were compared with a measured force polytope. The volume, shape and force prediction errors were assessed. The scaled ellipsoid underestimated the maximal mean force, and the scaled polytope overestimated it. The scaled force ellipsoid underestimated the volume of the measured force distribution, whereas that of the scaled polytope was not significantly different from the measured distribution but exhibited larger variability. All the models characterized well the elongated shape of the measured force distribution. The angles between the main axes of the modelled ellipsoids and polytopes and that of the measured polytope were compared. The values ranged from 7.3° to 14.3°. Over the entire surface of the force ellipsoid, 39.7% of the points had prediction errors less than 50 N; 33.6% had errors between 50 and 100 N; and 26.8% had errors greater than 100N. For the force polytope, the percentages were 56.2%, 28.3% and 15.4%, respectively.


2017 ◽  
Vol 14 (5) ◽  
pp. 172988141773189 ◽  
Author(s):  
Taihui Zhang ◽  
Honglei An ◽  
Hongxu Ma

Hydraulic actuated quadruped robot similar to BigDog has two primary performance requirements, load capacity and walking speed, so that it is necessary to balance joint torque and joint velocity when designing the dimension of single leg and controlling its motion. On the one hand, because there are three joints per leg on sagittal plane, it is necessary to firstly optimize the distribution of torque and angular velocity of every joint on the basis of their different requirements. On the other hand, because the performance of hydraulic actuator is limited, it is significant to keep the joint torque and angular velocity in actuator physical limitations. Therefore, it is essential to balance the joint torque and angular velocity which have negative correlation under the condition of constant power of the hydraulic actuator. The main purpose of this article is to optimize the distribution of joint torques and velocity of a redundant single leg with joint physical limitations. Firstly, a modified optimization criterion combining joint torques with angular velocity that takes both support phase and flight phase into account is proposed, and then the modified optimization criterion is converted into a normal quadratic programming problem. A kind of recurrent neural network is used to solve the quadratic program problem. This method avoids tremendous matrix inversion and fits for time-varying system. The achieved optimized distribution of joint torques and velocity is useful for aiding mechanical design and the following motion control. Simulation results presented in this article confirm the efficiency of this optimization algorithm.


2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Bradley Howard ◽  
Aimee Cloutier ◽  
Jingzhou (James) Yang

An understanding of human seated posture is important across many fields of scientific research. Certain demographics, such as pregnant women, have special postural limitations that need to be considered. Physics-based posture prediction is a tool in which seated postures can be quickly and thoroughly analyzed, as long the predicted postures are realistic. This paper proposes and validates an optimization formulation to predict seated posture for pregnant women considering ground and seat pan contacts. For the optimization formulation, the design variables are joint angles (posture); the cost function is dependent on joint torques. Constraints include joint limits, joint torque limits, the distances from the end-effectors to target points, and self-collision avoidance constraints. Three different joint torque cost functions have been investigated to account for the special postural characteristics of pregnant women and consider the support reaction forces (SRFs) associated with seated posture. Postures are predicted for three different reaching tasks in common reaching directions using each of the objective function formulations. The predicted postures are validated against experimental postures obtained using motion capture. A linear regression analysis was used to evaluate the validity of the predicted postures and was the criteria for comparison between the different objective functions. A 56 degree of freedom model was used for the posture prediction. Use of the objective function minimizing the maximum normalized joint torque provided an R2 value of 0.828, proving superior to either of two alternative functions.


2017 ◽  
Vol 31 (9) ◽  
pp. 814-826 ◽  
Author(s):  
Natalia Sánchez ◽  
Ana Maria Acosta ◽  
Roberto Lopez-Rosado ◽  
Arno H. A. Stienen ◽  
Julius P. A. Dewald

Although global movement abnormalities in the lower extremity poststroke have been studied, the expression of specific motor impairments such as weakness and abnormal muscle and joint torque coupling patterns have received less attention. We characterized changes in strength, muscle coactivation and associated joint torque couples in the paretic and nonparetic extremity of 15 participants with chronic poststroke hemiparesis (age 59.6 ± 15.2 years) compared with 8 age-matched controls. Participants performed isometric maximum torques in hip abduction, adduction, flexion and extension, knee flexion and extension, ankle dorsi- and plantarflexion and submaximal torques in hip extension and ankle plantarflexion. Surface electromyograms (EMGs) of 10 lower extremity muscles were measured. Relative weakness (paretic extremity compared with the nonparetic extremity) was measured in poststroke participants. Differences in EMGs and joint torques associated with maximum voluntary torques were tested using linear mixed effects models. Results indicate significant poststroke torque weakness in all degrees of freedom except hip extension and adduction, adductor coactivation during extensor tasks, in addition to synergistic muscle coactivation patterns. This was more pronounced in the paretic extremity compared with the nonparetic extremity and with controls. Results also indicated significant interjoint torque couples during maximum and submaximal hip extension in both extremities of poststroke participants and in controls only during maximal hip extension. Additionally, significant interjoint torque couples were identified only in the paretic extremity during ankle plantarflexion. A better understanding of these motor impairments is expected to lead to more effective interventions for poststroke gait and posture.


2021 ◽  
Author(s):  
Ali Nasr ◽  
Spencer Ferguson ◽  
John McPhee

Abstract To physically assist workers in reducing musculoskeletal strain or to develop motor skills for patients with neuromuscular disabilities, recent research has focused on Exoskeletons (Exos). Designing active Exos is challenging due to the complex human geometric structure, the human-Exoskeleton wrench interaction, the kinematic constraints, and the selection of power source characteristics. Because of the portable advantages of passive Exos, designing a passive shoulder mechanism has been studied here. The study concentrates on modeling a 3D multibody upper-limb human-Exoskeleton, developing a procedure of analyzing optimal assistive torque profiles, and optimizing the passive mechanism features for desired tasks. The optimization objective is minimizing the human joint torques. For simulating the complex closed-loop multibody dynamics, differential-algebraic equations (DAE)s of motion have been generated and solved. Three different tasks have been considered, which are common in industrial environments: object manipulation, over-head work, and static pointing. The resulting assistive Exoskeleton’s elevation joint torque profile could decrease the specific task’s human shoulder torque. Since the passive mechanism produces a specific torque for a given elevation angle, the Exoskeleton is not versatile or optimal for different dynamic tasks. We concluded that designing a passive Exoskeleton for a wide range of dynamic applications is impossible. We hypothesize that augmenting an actuator to the mechanism can provide the necessary adjustment torque and versatility for multiple tasks.


1997 ◽  
Vol 78 (6) ◽  
pp. 2985-2998 ◽  
Author(s):  
Gerald L. Gottlieb ◽  
Qilai Song ◽  
Gil L. Almeida ◽  
Di-An Hong ◽  
Daniel Corcos

Gottlieb, Gerald L., Qilai Song, Gil L. Almeida, Di-an Hong, and Daniel Corcos. Directional control of planar human arm movement. J. Neurophysiol. 78: 2985–2998, 1997. We examined the patterns of joint kinematics and torques in two kinds of sagittal plane reaching movements. One consisted of movements from a fixed initial position with the arm partially outstretched, to different targets, equidistant from the initial position and located according to the hours of a clock. The other series added movements from different initial positions and directions and >40–80 cm distances. Dynamic muscle torque was calculated by inverse dynamic equations with the gravitational components removed. In making movements in almost every direction, the dynamic components of the muscle torques at both the elbow and shoulder were related almost linearly to each other. Both were similarly shaped, biphasic, almost synchronous and symmetrical pulses. These findings are consistent with our previously reported observations, which we termed a linear synergy. The relative scaling of the two joint torques changes continuously and regularly with movement direction. This was confirmed by calculating a vector defined by the dynamic components of the shoulder and elbow torques. The vector rotates smoothly about an ellipse in intrinsic, joint torque space as the direction of hand motion rotates about a circle in extrinsic Cartesian space. This confirms a second implication of linear synergy that the scaling constant between the linearly related joint torques is directionally dependent. Multiple linear regression showed that the torque at each joint scales as a simple linear function of the angular displacement at both joints, in spite of the complex nonlinear dynamics of multijoint movement. The coefficients of this function are independent of the initial arm position and movement distance and are the same for all subjects. This is an unanticipated finding. We discuss these observations in terms of the hypothesis that voluntary, multiple degrees of freedom, rapid reaching movements may use rule-based, feed-forward control of dynamic joint torque. Rule-based control of joint torque with separate dynamic and static controllers is an alternative to models such as those based on the equilibrium point hypotheses that rely on a positionally based controller to produce both dynamic and static torque components. It is also an alternative to feed-forward models that directly solve the problems of inverse dynamics. Our experimental findings are not necessarily incompatible with any of the alternative models, but they describe new, additional findings for which we need to account. The rules are chosen by the nervous system according to features of the kinematic task to couple muscle contraction at the shoulder and elbow in a linear synergy. Speed and load control preserves the relative magnitudes of the dynamic torques while directional control is accomplished by modulating them in a differential manner. This control system operates in parallel with a positional control system that solves the problems of postural stability.


2005 ◽  
Vol 94 (5) ◽  
pp. 3046-3057 ◽  
Author(s):  
Jonathan Shemmell ◽  
Matthew Forner ◽  
James R. Tresilian ◽  
Stephan Riek ◽  
Benjamin K. Barry ◽  
...  

In this study we attempted to identify the principles that govern the changes in neural control that occur during repeated performance of a multiarticular coordination task. Eight participants produced isometric flexion/extension and pronation/supination torques at the radiohumeral joint, either in isolation (e.g., flexion) or in combination (e.g., flexion–supination), to acquire targets presented by a visual display. A cursor superimposed on the display provided feedback of the applied torques. During pre- and postpractice tests, the participants acquired targets in eight directions located either 3.6 cm (20% maximal voluntary contraction [MVC]) or 7.2 cm (40% MVC) from a neutral cursor position. On each of five consecutive days of practice the participants acquired targets located 5.4 cm (30% MVC) from the neutral position. EMG was recorded from eight muscles contributing to torque production about the radiohumeral joint during the pre- and posttests. Target-acquisition time decreased significantly with practice in most target directions and at both target torque levels. These performance improvements were primarily associated with increases in the peak rate of torque development after practice. At a muscular level, these changes were brought about by increases in the rates of recruitment of all agonist muscles. The spatiotemporal organization of muscle synergies was not significantly altered after practice. The observed adaptations appear to lead to performances that are generalizable to actions that require both greater and smaller joint torques than that practiced, and may be successfully recalled after a substantial period without practice. These results suggest that tasks in which performance is improved by increasing the rate of muscle activation, and thus the rate of joint torque development, may benefit in terms of the extent to which acquired levels of performance are maintained over time.


Sign in / Sign up

Export Citation Format

Share Document