Increase in ovality of uranium tubes due to creep under external pressure

1968 ◽  
Vol 3 (3) ◽  
pp. 226-231
Author(s):  
W S Blackburn ◽  
J Percy

The increase in ellipticity of a concentric slightly elliptical tube is theoretically investigated for the case of external pressure and radial temperature gradient when the creep rate is proportional to the stress and the constant of proportionality varies slightly between the principal axes. The presence of a radial temperature gradient accelerates the increase in ovality due to initial ovality on the outer surface and that due to circumferential variation of strength (except after very small collapses) and decreases that due to initial inner ovality. Further allowance for circumferential variation in temperature, due to an insulated inner surface and to a uniform heat-transfer coefficient to a gas at constant temperature around the outer surface, reduces the increase in all cases.

Author(s):  
Liangxiang Ma ◽  
Jianghui Zhang ◽  
Xiang Ma ◽  
Zongbao Gu ◽  
Yan He ◽  
...  

Abstract A flow boiling heat transfer experimental investigation on the shell-side of a smooth tube and two enhanced tubes (C-EHT, P-EHT) was performed using R410A as working fluid. The outer surface of the C-EHT tube is covered with special fins having a salient height, and the inner surface has a thread structure with the same distribution density. The outer surface of the P-EHT tube has lots of tiny pits formed by high-strength sandblasting and smooth inner surface. The inlet and outlet vapor quality is 0.2 and 0.8 at a saturation temperature of 279K. The flow boiling experimental results show that the evaporation heat transfer coefficient of C-EHT tube is the largest among the tested tubes. However, for the P-EHT tube, its heat transfer coefficient is lower than that of smooth tube. C-EHT tube with special fins has higher heat transfer area, which can also intensify the interfacial turbulence with increasing fins. The reason why the flow boiling heat transfer coefficient of the P-EHT tube is lower than that of the smooth tube is that the diameter of the pit on P-EHT tube is too small to form the nucleation cites, which results in bubble retention under the condition of low mass flux and deteriorates the flow boiling heat transfer performance.


Author(s):  
Magdalena Jaremkiewicz

Purpose The purpose of this paper is to propose a method of determining the transient temperature of the inner surface of thick-walled elements. The method can be used to determine thermal stresses in pressure elements. Design/methodology/approach An inverse marching method is proposed to determine the transient temperature of the thick-walled element inner surface with high accuracy. Findings Initially, the inverse method was validated computationally. The comparison between the temperatures obtained from the solution for the direct heat conduction problem and the results obtained by means of the proposed inverse method is very satisfactory. Subsequently, the presented method was validated using experimental data. The results obtained from the inverse calculations also gave good results. Originality/value The advantage of the method is the possibility of determining the heat transfer coefficient at a point on the exposed surface based on the local temperature distribution measured on the insulated outer surface. The heat transfer coefficient determined experimentally can be used to calculate thermal stresses in elements with a complex shape. The proposed method can be used in online computer systems to monitor temperature and thermal stresses in thick-walled pressure components because the computing time is very short.


Author(s):  
D.V. Tarasevych ◽  
◽  
O.V. Bogdan ◽  

When choosing architectural and planning solutions, such climatic factors as air temperature and humidity, having scalar quantities, as well as solar radiation, wind and precipitation having vector characteristics, must be taken into account. The calculated climatic parameters for the design of building enclosing structures, heat loss calculations and heat supply regulation are provided in the current documentation on norms and standards. The practical exploitation of various buildings demonstrates that in terms of initial climatic data, the choice of design parameters is not always efficiently justified; hence, the influence of the environment on the heating regime of the structures is insufficient in the estimations and sometimes erroneous. The wind is one of such climatic parameters. Its velocity and repeatability impact the heat exchange of the building structure with the environment as well as the alteration in temperature regime. The wind current towards the building creates additional pressure on the facade of the construction from the wind side direction. This leads, firstly, to air infiltration via the enclosing structures, and secondly, to the rise of heat exchange from the outer surface of the wall on the windward side. Based on estimated and analytical research, the values of the change in wind velocity depending on the altitude were analyzed, and its influence on the heat loss during heating of multi-storey buildings was assessed. The alterations in the wind velocity depending on the altitude were analyzed in the conditions of dense (urban) and broad construction. Besides, the authors presented the dependence of the convective component of the heat transfer coefficient of the outer surface of the structure on the values of the wind velocity. Based on the performed and presented calculations, it can be noticed that the heat transfer of the external structure will be much higher for multi-storey buildings than for mid-rise constructions. Thus, the convective component of the heat transfer coefficient of the outer surface rises by 36 % when the wind velocity increases from 5 m/s to 7 m/s. If not taking into consideration this dependence in the design, it can significantly influence the estimation of heat loss and energy efficiency of buildings, especially when it is about the increased percentage of facades glazing. The authors of the article assessed the heat loss for heating the windward and leeward facades at average values of the outside air temperature during the heating season in Ukraine. Hence, for constructions higher than 70 m with a calculated wind velocity of 5 m/s, heat losses increase from 10 % to 19 %. Such great difference in heat loss between the windward and leeward walls of the building requires increased thermal protection from the prevailing winter winds. Therefore, when designing multi-storey buildings, it is necessary to take into account changes in wind velocity according to the altitude. The obtained results can be useful both for choosing architectural and planning solutions, like the materials for external enclosing structures and for the objective assessment of the wind protection degree of individual buildings and territories.


2013 ◽  
Vol 740-742 ◽  
pp. 77-80
Author(s):  
Jung Young Jung ◽  
Sang Il Lee ◽  
Mi Seon Park ◽  
Doe Hyung Lee ◽  
Hee Tae Lee ◽  
...  

The present research was focused to investigate the effect of internal crucible design that influenced the 4H-SiC crystal growth onto a 6H-SiC seed by PVT method. The crucible design was modified to produce a uniform radial temperature gradient in the growth cell. The seed attachment was also modified with a use of polycrystalline SiC plate. The crystal quality of 4H-SiC single crystals grown in modified crucible and grown with modified seed attachment was revealed to be better than that of crystal grown in conventional crucible. The full width at half maximum (FWHM) values of grown SiC crystals in the conventional crucible, the modified seed attachment and the modified crucible were 285 arcsec, 134 arcsec and 128 arcsec, respectively. The micropipe density (MPD) of grown SiC crystals in the conventional crucible, the modified seed attachment and the modified crucible were 101ea/cm^2, 81ea/cm^2 and 42ea/cm^2, respectively.


Sign in / Sign up

Export Citation Format

Share Document