scholarly journals Elastic stress concentration at radial crossholes in pressurized thick cylinders

2007 ◽  
Vol 42 (6) ◽  
pp. 461-468 ◽  
Author(s):  
T Comlekci ◽  
D Mackenzie ◽  
R Hamilton ◽  
J Wood
Keyword(s):  
Stress Concentration ◽  
Maximum Stress ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
Maximum Principal Stress ◽  
Radius Ratio ◽  
Graphical Form ◽  
Element Analysis ◽  
Parametric Finite Element Analysis ◽  
Von Mises

Results of a parametric finite element analysis investigation of stress concentration at radial crossholes in pressurized cylinders are presented in numerical and graphical form. The analysis shows that the location of maximum stress does not generally occur at the junction between the bores, as is commonly supposed, but at some small distance up the crosshole from the junction. Maximum stress concentration factors (SCFs) are defined on the basis of the maximum principal stress, von Mises equivalent stress, and stress intensity. Three-dimensional plots of the SCF against the cylinder radius ratio b/a and the crosshole-to-main-bore-radius ratio c/a are presented. The SCFs were found to vary across the range of geometries considered with local minima identified within the parameter range in most cases. The results therefore allow designers to select optimum b/a and c/a ratios to minimize stress concentration in real problems.

scholarly journals Influence of Sagittal Root Positions on the Stress Distribution Around Custom-made Root-analogue Implants: A Three-dimensional Finite Element Analysis

2021 ◽  
Author(s):  
Chunping Lin ◽  
Hongcheng Hu ◽  
Junxin Zhu ◽  
Yuwei Wu ◽  
Qiguo Rong ◽  
...  
Keyword(s):  
Stress Concentration ◽  
Three Dimensional ◽  
Class Ii ◽  
Class I ◽  
Von Mises Stress ◽  
Class Iii ◽  
Element Analysis ◽  
Custom Made ◽  
Root Position ◽  
Von Mises

Abstract Background: Stress concentration may cause bone resorption even lead to the failure of implantation. This study was designed to investigate whether a certain sagittal root position could cause stress concentration around maxillary anterior custom-made root-analogue implants via three-dimensional finite element analysis.Methods: Six models were constructed and divided into two groups. The smooth group included models of unthreaded custom-made implants in Class I, II or III sagittal root positions. The threaded group included models of reverse buttress-threaded implants in the three positions. Stress distributions under vertical and oblique loads of 100 N were analyzed.Results: Stress concentrations around the labial lamella area were more prominent in the Class I position than in the Class II and Class III positions under oblique loading. Under vertical loading, the most obvious stress concentration areas were the labial lamella and palatal apical areas in the Class I and Class III positions, respectively. Stress was relatively distributed in the labial and palatal lamellae in the Class II position. The maximum von Mises stress in the bone around the custom-made root-analogue implants in this study was lower than around traditional implants reported in the literature. Additionally, compared to the smooth group, the threaded group showed lower von Mises stress in the bone around the implants.Conclusions: The sagittal root position affected the von Mises stress distribution around custom-made root-analogue implants. There was no certain sagittal root position that could cause excessive stress concentration around the custom-made root-analogue implants. Among the three sagittal root positions, the Class II position would be the most appropriate site for custom-made root-analogue implants.

Fastener Pattern Optimization of an Eccentrically Loaded Multi-Fastener Connection

2010 ◽  
Author(s):  
Matthew Watkins ◽  
Mark Jakiela
Keyword(s):  
Stress Concentration ◽  
Maximum Stress ◽  
Fatigue Cracks ◽  
Frictional Resistance ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Fastener Hole ◽  
Type Contact ◽  
Instantaneous Center ◽  
Von Mises

This paper presents the use of a genetic algorithm in conjunction with geometric nonlinear finite element analysis to optimize the fastener pattern and lug location in an eccentrically loaded multi-fastener connection. No frictional resistance to shear was included in the model, as the connection transmitted shear loads into four dowel fasteners through bearing-type contact without fastener preload. With the goal of reducing the maximum von Mises stress in the connection to improve fatigue life, the location of the lug hole and four fastener holes were optimized to achieve 55% less maximum stress than a similar optimization using the traditional instantaneous center of rotation method. Since the maximum stress concentration was located at the edge of a fastener hole where fatigue cracks could be a concern, reduction of this quantity lowers the probability of crack growth for both bearing-type and slip-resistant connections. It was also found that the location of the maximum von Mises stress concentration jumped from the fastener region to the lug as the applied force angle was decreased below 45 degrees, thus the fastener pattern could not be optimized for lower angles.

Fitness for Service of Dents Associated With Metal Loss due to Corrosion

2014 ◽  
Author(s):  
Hans Olav Heggen ◽  
Joe Bratton ◽  
David Kemp ◽  
Jun Liu ◽  
Jason Austin
Keyword(s):  
Fatigue Life ◽  
Stress Concentration ◽  
Maximum Stress ◽  
Dynamic Pressure ◽  
Equivalent Stress ◽  
Metal Loss ◽  
General Effect ◽  
Element Analysis ◽  
Pressure Cycling ◽  
Pressure Cycle

Current federal regulations in the U.S. require excavation of all dents associated with metal loss due to corrosion identified through in line inspection surveys. Once a dent has been found to be associated with metal loss through excavation, there is little guidance to determine the serviceability of the anomaly. Past research has provided methodologies to assess the fatigue life of plain dents, considering the shape of the dent, but there are no widely accepted assessment methodologies to predict the effect of associated metal loss due to corrosion on the fatigue life of dents. This paper focuses on the fitness for service of dents associated with metal loss, particularly corrosion in dents. Currently, fitness for service assessments of plain dents provide an estimated remaining life of a dent based on the geometry of the dent and current pressure cycling of the pipeline. Dynamic pressure cycling at each dent location is estimated using the upstream and downstream pressure cycle data, elevation, and distance along the pipe. The dynamic pressure cycle data at each dent is then converted into equivalent stress cycles based on the results of rainflow cycle counting. Finite element analysis (FEA) of a dent without metal loss and with metal loss is performed to compare the maximum stress concentration areas. The FEA program Abaqus is used with solid elements to model the dents. The differences between maximum stress concentration areas is compared for a matrix of extent of metal loss, and orientation of metal loss to analyze the general effect of metal loss and the interaction of metal loss in a dent. The stress concentration areas of dents without metal loss and with metal loss are then applied to current fatigue assessment methodologies provided in API 579 to analyze the effect of metal loss on the fatigue life of dents.

Updated Stress Concentration Factors for Filleted Shafts in Bending and Tension

1996 ◽  
Vol 118 (3) ◽  
pp. 321-327 ◽  
Author(s):  
S. M. Tipton ◽  
J. R. Sorem ◽  
R. D. Rolovic
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Maximum Stress ◽  
Elastic Stress ◽  
Equivalent Stress ◽  
Graphical Form ◽  
Fatigue Crack Nucleation ◽  
Wide Range ◽  
Concentration Factors ◽  
Stress Concentration Factors

Published elastic stress concentration factors are shown to underestimate stresses in the root of a shoulder filleted shaft in bending by as much as 21 percent, and in tension by as much as forty percent. For this geometry, published charts represent only approximated stress concentration factor values, based on known solutions for similar geometries. In this study, detailed finite element analyses were performed over a wide range of filleted shaft geometries to define three useful relations for bending and tension loading: (1) revised elastic stress concentration factors, (2) revised elastic von Mises equivalent stress concentration factors and (3) the maximum stress location in the fillet. Updated results are presented in the familiar graphical form and empirical relations are fit through the curves which are suitable for use in numerical design algorithms. It is demonstrated that the first two relations reveal the full multiaxial elastic state of stress and strain at the maximum stress location. Understanding the influence of geometry on the maximum stress location can be helpful for experimental strain determination or monitoring fatigue crack nucleation. The finite element results are validated against values published in the literature for several geometries and with limited experimental data.

scholarly journals STRESS CONCENTRATION IN ISOTROPIC & ORTHOTROPIC COMPOSITE PLATES WITH CENTER CIRCULAR HOLE SUBJECTED TO TRANSVERSE STATIC LOADING

2014 ◽  
pp. 16-20
Author(s):  
MOON BANERJEE ◽  
N. K. JAIN ◽  
S. SANYAL
Keyword(s):  
Stress Concentration ◽  
Circular Hole ◽  
Static Loading ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Composite Plates ◽  
Graphical Form ◽  
Orthotropic Composite ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The present study brings out the thorough analysis of isotropic and orthotropic fixed rectangular plate with center circular hole under transverse static loading condition. In this paper influence of stress concentration and deflection due to singularity for isotropic and orthotropic composite materials under different parametric conditions is obtained. The effect of thickness -to- width of plate (T/A) and diameter-to-width (D/A) ratio upon stress concentration factor (SCF) for different stresses were studied. An isotropic and one composite material were considered for analysis to determine the variation of SCF with elastic constants. Deflection in transverse direction were calculated and analyzed. Results are presented in graphical form and discussed. Three-dimensional finite element models were created using ANSYS software. Results showed that maximum stress appear near the vicinity of the hole at the upper and lower portions of the plate. The effect of material properties, (E1/E2) on SCF for stresses along x, y and z axis is established thorough this analysis.

scholarly journals Finite Element Analysis of Stress in Bone and Abutment-Implant Interface under Static and Cyclic Loadings

2020 ◽  
Author(s):  
Saeed Nokar ◽  
Hamid Jalali ◽  
Farideh Nozari ◽  
Mahnaz Arshad
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Maximum Stress ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Bone Implant ◽  
Factors Affecting ◽  
Von Mises

Objectives: The success of implant treatment depends on many factors affecting the bone-implant, implant-abutment, and abutment-prosthesis interfaces. Stress distribution in bone plays a major role in success/failure of dental implants. This study aimed to assess the pattern of stress distribution in bone and abutment-implant interface under static and cyclic loadings using finite element analysis (FEA). Materials and Methods: In this study, ITI implants (4.1×12 mm) placed at the second premolar site with Synocta abutments and metal-ceramic crowns were simulated using SolidWorks 2007 and ABAQUS software. The bone-implant contact was assumed to be 100%. The abutments were tightened with 35 Ncm preload torque according to the manufacturer’s instructions. Static and cyclic loads were applied in axial (116 Ncm), lingual (18 Ncm), and mesiodistal (24 Ncm) directions. The maximum von Mises stress and strain values ​​were recorded. Results: The maximum stress concentration was at the abutment neck during both static and cyclic loadings. Also, maximum stress concentration was observed in the cortical bone. The loading stress was higher in cyclic than static loading. Conclusion: Within the limitations of this study, it can be concluded that the level of stress in single-unit implant restorations is within the tolerable range by bone.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

Influence of Slope Gradient on Distribution Rule of Geostress Field in River Valleys

2013 ◽  
Vol 404 ◽  
pp. 365-370 ◽  
Author(s):  
Qi Tao Pei ◽  
Hai Bo Li ◽  
Ya Qun Liu ◽  
Jun Gang Jiang
Keyword(s):  
Numerical Simulation ◽  
Stress Concentration ◽  
Principal Stress ◽  
Three Dimensional ◽  
Maximum Principal Stress ◽  
Slope Gradient ◽  
Bank Slope ◽  
Distribution Rule ◽  
River Valleys ◽  
Gradient Change

During the construction of hydropower station, the change of slope gradient in river valleys often takes place. In order to study influence of slope gradient change on distribution rule of geostress field, the three dimensional unloading models under different slope gradients were established by finite difference software (FLAC3D). After numerical simulation, the results were as follows: (1) The phenomenon of stress concentration at the bottom of river valleys was obvious, which appeared the typical stress fold. Both the depth of stress concentration zone and the principal stress values significantly increased with the increment of slope gradient. (2) Maximum principal stress values increased less in shallow part of upper bank slope (low stress zone) but increased more in the nearby slope foot with the increment of slope gradient, causing great difference in geostress field of bank slope. (3) There was some difference in released energy of bank slope due to slope gradient change in river valleys. In order to distinguish the difference, stress relief zone was further divided into stress stably released zone and stress instability released zone. Finally, take Ada dam area of the western route project of South-to-North Water Transfer as an example, the results by numerical simulation were reliable through comparing the distribution rule of geostress field for the dam, which could provide important reference for stability of the design and construction of steep and narrow river valleys.

Determination of Stress Concentration Around an Oblique Hole by a Finite-Element Technique

1983 ◽  
Vol 105 (2) ◽  
pp. 206-212 ◽  
Author(s):  
Hua-Ping Li ◽  
F. Ellyin
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Maximum Stress ◽  
Plate Thickness ◽  
Two Dimensional ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Parametric Studies ◽  
Element Technique

A plate weakened by an oblique penetration of a circular cylindrical hole has been investigated. The stress concentration around the hole is determined by a finite-element method. The results are compared with experimental data and other analytical works. Parametric studies of effects of angle of inclination, plate thickness, and width are performed. The maximum stress concentration factor (SCF) obtained from the finite-element analysis is higher than experimental results, and this deviation increases with the increase of angle of skewness. The major reason for this difference is attributed to the shear-action between layers parallel to the plate surface which cannot be directly included in the two-dimensional elements. An empirical formula is derived which accounts for the shear-action and renders the finite-element predictions in line with experimentally observed data.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

Sign in / Sign up

Export Citation Format

Share Document