Equivalent model of semi-rigid supporting node in the calculations of steel frames

2016 ◽  
pp. 451-456
Author(s):  
P Krystosik
Keyword(s):  
Steel Frames ◽  
Equivalent Model

Discrete optimization of semi-rigid steel frames in second-order analysis

2019 ◽  
Author(s):  
Marcos Henrique Bossardi Borges ◽  
Adelano Esposito ◽  
Herbert Gomes
Keyword(s):  
Discrete Optimization ◽  
Steel Frames ◽  
Second Order ◽  
Order Analysis

Determination of the transverse shear stress in layered composites

2020 ◽  
Vol 86 (2) ◽  
pp. 44-53
Author(s):  
Yu. I. Dudarkov ◽  
M. V. Limonin
Keyword(s):  
Shear Stress ◽  
Transverse Shear ◽  
Composite Beam ◽  
Layered Composite ◽  
Equivalent Model ◽  
Shear Stresses ◽  
Transverse Shear Stress ◽  
Layered Composites ◽  
Laminate Composites ◽  
Transverse Shear Stresses

An engineering approach to estimation of the transverse shear stresses in layered composites is developed. The technique is based on the well-known D. I. Zhuravsky equation for shear stresses in an isotropic beam upon transverse bending. In general, application of this equation to a composite beam is incorrect due to the heterogeneity of the composite structure. According to the proposed method, at the first stage of its implementation, a transition to the equivalent model of a homogeneous beam is made, for which the Zhuravsky formula is valid. The transition is carried out by changing the shape of the cross section of the beam, provided that the bending stiffness and generalized elastic modulus remain the same. The calculated shear stresses in the equivalent beam are then converted to the stress values in the original composite beam from the equilibrium condition. The main equations and definitions of the method as well as the analytical equation for estimation of the transverse shear stress in a composite beam are presented. The method is verified by comparing the analytical solution and the results of the numerical solution of the problem by finite element method (FEM). It is shown that laminate stacking sequence has a significant impact both on the character and on the value of the transverse shear stress distribution. The limits of the applicability of the developed technique attributed to the conditions of the validity of the hypothesis of straight normal are considered. It is noted that under this hypothesis the shear stresses do not depend on the layer shear modulus, which explains the absence of this parameter in the obtained equation. The classical theory of laminate composites is based on the similar assumptions, which gives ground to use this equation for an approximate estimation of the transverse shear stresses in in a layered composite package.

EXPERIMENTAL INVESTIGATION ON WAIST-INDUCED SWAY COLLAPSE OF STEEL FRAMES

1982 ◽  
Vol 315 (0) ◽  
pp. 48-60
Author(s):  
Tsuneyoshi NAKAMURA ◽  
Osamu OHTA ◽  
Koji UETANI
Keyword(s):  
Experimental Investigation ◽  
Steel Frames

Determining the Norton’s Equivalent Model of Distribution System with Distributed Generation (DG) for Stability Analysis

2019 ◽  
Vol 12 (2) ◽  
pp. 190-198
Author(s):  
Sunny Katyara ◽  
Lukasz Staszewski ◽  
Faheem Akhtar Chachar
Keyword(s):  
Distributed Generation ◽  
Normal Condition ◽  
Distribution System ◽  
Distribution Networks ◽  
Equivalent Model ◽  
Stability Factor ◽  
Matlab Simulation ◽  
The Stability ◽  
Stability Issues

Background: Since the distribution networks are passive until Distributed Generation (DG) is not being installed into them, the stability issues occur in the distribution system after the integration of DG. Methods: In order to assure the simplicity during the calculations, many approximations have been proposed for finding the system’s parameters i.e. Voltage, active and reactive powers and load angle, more efficiently and accurately. This research presents an algorithm for finding the Norton’s equivalent model of distribution system with DG, considering from receiving end. Norton’s model of distribution system can be determined either from its complete configuration or through an algorithm using system’s voltage and current profiles. The algorithm involves the determination of derivative of apparent power against the current (dS/dIL) of the system. Results: This work also verifies the accuracy of proposed algorithm according to the relative variations in the phase angle of system’s impedance. This research also considers the varying states of distribution system due to switching in and out of DG and therefore Norton’s model needs to be updated accordingly. Conclusion: The efficacy of the proposed algorithm is verified through MATLAB simulation results under two scenarios, (i) normal condition and (ii) faulty condition. During normal condition, the stability factor near to 1 and change in dS/dIL was near to 0 while during fault condition, the stability factor was higher than 1 and the value of dS/dIL was away from 0.

Comparison of steel frames with RWS and WFP beam-to-column connections through seismic fragility analysis

2020 ◽  
pp. 136943322097728
Author(s):  
Haoran Yu ◽  
Weibin Li
Keyword(s):  
Limit State ◽  
Pushover Analysis ◽  
Steel Frames ◽  
Fragility Analysis ◽  
Structural Safety ◽  
Seismic Fragility ◽  
Fe Modelling ◽  
Collapse Resistance ◽  
Seismic Collapse ◽  
Probabilistic Seismic Demand

Reduced web section (RWS) connections and welded flange plate (WFP) connections can both effectively improve the seismic performance of a structure by moving plastic hinges to a predetermined location away from the column face. In this paper, two kinds of steel frames—with RWS connections and WFP connections—as well as different frames with welded unreinforced flange connections were studied through seismic fragility analysis. The numerical simulation was conducted by using multiscale FE modelling. Based on the incremental dynamic analysis and pushover analysis methods, probabilistic seismic demand analysis and seismic capability analysis were carried out, respectively. Finally, combined with the above analysis results, probabilistic seismic fragility analysis was conducted on the frame models. The results showed that the RWS connection and WFP connection (without double plates) have little influence on reducing the maximum inter-storey drift ratio under earthquake action. RWS connections slightly reduce the seismic capability in non-collapse stages and improve the seismic collapse resistance of a structure, which exhibits good structural ductility. WFP connections can comprehensively improve the seismic capability of a structure, but the seismic collapse resistance is worse than that of RWS connections when the structure has a large number of storeys. The frame with WFP connections has a lower failure probability at every seismic limit state, while the frame with RWS connections sacrifices some of its structural safety in non-collapse stages to reduce the collapse probability.

scholarly journals Modeling Stray Capacitances of High-Voltage Capacitive Dividers for Conventional Measurement Setups

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1262
Author(s):  
Alessandro Mingotti ◽  
Federica Costa ◽  
Lorenzo Peretto ◽  
Roberto Tinarelli ◽  
Paolo Mazza
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Equivalent Circuit ◽  
High Voltage ◽  
Equivalent Model ◽  
Simulation Environment ◽  
Element Analysis ◽  
Ratio Error ◽  
Complicated Geometries

Stray capacitances (SCs) are a serious issue in high-voltage (HV) applications. Their presence can alter the circuit or the operation of a device, resulting in wrong or even disastrous consequences. To this purpose, in this work, we describe the modeling of SCs in HV capacitive dividers. Such modeling does not rely on finite element analysis or complicated geometries; instead, it starts from an equivalent circuit of a conventional measurement setup described by the standard IEC 61869-11. Once the equivalent model including the SCs is found, closed expressions of the SCs are derived starting from the ratio error definition. Afterwards, they are validated in a simulation environment by implementing various circuit configurations. The results demonstrate the expressions applicability and effectiveness; hence, thanks to their simplicity, they can be implemented by system operators, researchers, and manufacturers avoiding the use of complicated methods and technologies.

Sign in / Sign up

Export Citation Format

Share Document