Shakedown optimization of the Thin-Wall Metal structures under strength and stiffness constrains

2016 ◽  
pp. 393-400
Author(s):  
P Alawdin ◽  
L Liepa
Keyword(s):  
Thin Wall ◽  
Metal Structures ◽  
Strength And Stiffness

scholarly journals Optimal Shakedown of the Thin-Wall Metal Structures Under Strength and Stiffness Constraints

2017 ◽  
Vol 25 (2) ◽  
pp. 25-41
Author(s):  
Piotr Alawdin ◽  
Liudas Liepa
Keyword(s):  
Cross Sections ◽  
Optimization Problem ◽  
Optimization Problems ◽  
Thin Wall ◽  
Lateral Torsional Buckling ◽  
Static Loads ◽  
Metal Structures ◽  
Buckling Behavior ◽  
Plane Frames ◽  
Strength And Stiffness

Abstract Classical optimization problems of metal structures confined mainly with 1st class cross-sections. But in practice it is common to use the cross-sections of higher classes. In this paper, a new mathematical model for described shakedown optimization problem for metal structures, which elements are designed from 1st to 4th class cross-sections, under variable quasi-static loads is presented. The features of limited plastic redistribution of forces in the structure with thin-walled elements there are taken into account. Authors assume the elastic-plastic flexural buckling in one plane without lateral torsional buckling behavior of members. Design formulae for Methods 1 and 2 for members are analyzed. Structures stiffness constrains are also incorporated in order to satisfy the limit serviceability state requirements. With the help of mathematical programming theory and extreme principles the structure optimization algorithm is developed and justified with the numerical experiment for the metal plane frames.

Design Analysis of a Single-Column Pressframe

1984 ◽  
Vol 106 (4) ◽  
pp. 508-516 ◽  
Author(s):  
U. P. Singh
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Curved Beam ◽  
Thin Wall ◽  
The Finite Element Method ◽  
Beam Elements ◽  
Single Column ◽  
Deformed State ◽  
Strength And Stiffness ◽  
Theoretical Results

It is observed in practice that the classic (conventional) method as well as the finite element method, when using beam elements, to evaluate the strength and stiffness of a pressframe, gives results differing substantially from actual values. This discrepancy between experimental and theoretical results can be considerably narrowed if the stress-deformed state of the corner zone is separately considered in the computation of the overall strength and stiffness of the pressframe. By means of the application of the theory of thin-wall curved beam with large curvature it is economically possible to analyze the stress-deformed behavior of the pressform in general and the corner zone element in particular with fair reliability. In the present paper this method is applied to a mechanical C-frame press.

scholarly journals Development and study of mechanical behaviour reinforcing composites by waste BTP

2018 ◽  
Vol 149 ◽  
pp. 02012
Author(s):  
M.El kanzaoui ◽  
A. Hajjaji ◽  
A. Guenbour ◽  
R. Boussen
Keyword(s):  
Composite Materials ◽  
Mechanical Response ◽  
Industrial Applications ◽  
Waste Materials ◽  
Structural Elements ◽  
Ceramic Filler ◽  
Metal Structures ◽  
Stiffness Properties ◽  
Strength And Stiffness ◽  
Very High

Composite materials are used in many industrial applications for their excellent mechanical and electric properties and their low density compared to metal structures. Most countries are extremely rich waste materials such as white ceramic breakages which represents a potential to be developed. Ceramic breakages have exceptional properties and could be effectively exploited in the manufacture of composite materials for a wide variety of applications. The composite materials reinforced by construction waste materials, such as ceramic breaks which offer significant benefits and gains in strength and stiffness properties (Young's modulus E : a material whose modulus Young is very high is said rigid).This article covers the benefits of breakages as ceramic filler used for reinforcement in composites, as well as improve the mechanical response of these structural elements (test compression).

Microstructural characterization of plasma-processed Ti-Al metal matrix composites

1989 ◽  
Vol 47 ◽  
pp. 552-553
Author(s):  
M. G. Burke ◽  
M. N. Gungor ◽  
M. A. Burke
Keyword(s):  
High Temperature ◽  
Titanium Aluminide ◽  
Plasma Processing ◽  
Microstructural Characterization ◽  
High Temperature Strength ◽  
Matrix Composites ◽  
Intermetallic Matrix ◽  
Long Time ◽  
Strength And Stiffness ◽  
Intermetallic Matrix Composites

Intermetallic matrix composites are candidates for ultrahigh temperature service when light weight and high temperature strength and stiffness are required. Recent efforts to produce intermetallic matrix composites have focused on the titanium aluminide (TiAl) system with various ceramic reinforcements. In order to optimize the composition and processing of these composites it is necessary to evaluate the range of structures that can be produced in these materials and to identify the characteristics of the optimum structures. Normally, TiAl materials are difficult to process and, thus, examination of a suitable range of structures would not be feasible. However, plasma processing offers a novel method for producing composites from difficult to process component materials. By melting one or more of the component materials in a plasma and controlling deposition onto a cooled substrate, a range of structures can be produced and the method is highly suited to examining experimental composite systems. Moreover, because plasma processing involves rapid melting and very rapid cooling can be induced in the deposited composite, it is expected that processing method can avoid some of the problems, such as interfacial degradation, that are associated with the relatively long time, high temperature exposures that are induced by conventional processing methods.

Factors affecting microstructural scale in liquid crystalline polymers

1990 ◽  
Vol 48 (4) ◽  
pp. 220-221
Author(s):  
Christine M. Dannels ◽  
Christopher Viney
Keyword(s):  
Liquid Crystalline ◽  
Liquid Crystalline Polymers ◽  
Factors Affecting ◽  
Crystalline Polymers ◽  
Thermal Expansion Coefficients ◽  
Low Thermal Expansion ◽  
Lower Viscosity ◽  
Fine Microstructure ◽  
Planar Orientation ◽  
Strength And Stiffness

Processing polymers from the liquid crystalline state offers several advantages compared to processing from conventional fluids. These include: better axial strength and stiffness in fibers, better planar orientation in films, lower viscosity during processing, low solidification shrinkage of injection moldings (thermotropic processing), and low thermal expansion coefficients. However, the compressive strength of the solid is disappointing. Previous efforts to improve this property have focussed on synthesizing stiffer molecules. The effect of microstructural scale has been overlooked, even though its relevance to the mechanical and physical properties of more traditional materials is well established. By analogy with the behavior of metals and ceramics, one would expect a fine microstructure (i..e. a high density of orientational defects) to be desirable.Also, because much microstructural detail in liquid crystalline polymers occurs on a scale close to the wavelength of light, light is scattered on passing through these materials.

Observing the relaxation of molecular orientation in sheared liquid crystalline polymer solutions

1990 ◽  
Vol 48 (4) ◽  
pp. 1092-1093
Author(s):  
Wendy Putnam ◽  
Christopher Viney
Keyword(s):  
Molecular Orientation ◽  
Liquid Crystalline Polymer ◽  
Liquid Crystalline ◽  
Crystalline Polymer ◽  
Polymer Processing ◽  
Molecular Alignment ◽  
Global Alignment ◽  
Shear Direction ◽  
Axial Strength ◽  
Strength And Stiffness

Liquid crystalline polymers (solutions or melts) can be spun into fibers and films that have a higher axial strength and stiffness than conventionally processed polymers. These superior properties are due to the spontaneous molecular extension and alignment that is characteristic of liquid crystalline phases. Much of the effort in processing conventional polymers goes into extending and aligning the chains, while, in liquid crystalline polymer processing, the primary microstructural rearrangement involves converting local molecular alignment into global molecular alignment. Unfortunately, the global alignment introduced by processing relaxes quickly upon cessation of shear, and the molecular orientation develops a periodic misalignment relative to the shear direction. The axial strength and stiffness are reduced by this relaxation.Clearly there is a need to solidify the liquid crystalline state (i.e. remove heat or solvent) before significant relaxation occurs. Several researchers have observed this relaxation, mainly in solutions of hydroxypropyl cellulose (HPC) because they are lyotropic under ambient conditions.

STOCHASTIC CALCULATION OF LIFETIME PREDICTION FOR COMPONENTS IN METAL STRUCTURES DUE TO THE GROWTH OF MICRODEFECTS

2020 ◽  
Vol 4 (97) ◽  
pp. 69-76
Author(s):  
IGOR N. SILVERSTOV
Keyword(s):  
Fatigue Strength ◽  
Fracture Mechanics ◽  
Stochastic Approach ◽  
Fatigue Curve ◽  
Probability Of Failure ◽  
Lifetime Prediction ◽  
Statistical Distributions ◽  
Metal Structures

A stochastic approach has been developed to evaluate fatigue strength using elements of the fracture mechanics. The article presents a method for determining the initial parameters of statistical distributions. It also considers the method for constructing a fatigue curve for a component of any size and configuration with any given probability of failure.

RECLAMATION AND CULVERT CROSSINGS MADE OF CORRUGATED PIPES ON SPAWNING STREAMS

2020 ◽  
pp. 68-77
Author(s):  
O.N. CHERNYKH ◽  
◽  
A.V. RBURLACHENKO
Keyword(s):  
Single Point ◽  
Experimental Studies ◽  
Fish Passage ◽  
Future Research ◽  
Fish Stocks ◽  
Metal Structures ◽  
Natural Reproduction ◽  
Spiral Shape ◽  
Corrugated Metal ◽  
Spawning Streams

Recommendations are presented for solving issues that arise in the design and operation of tubular transport crossings of corrugated metal structures through spawning streams while ensuring the safety and natural reproduction of fish stocks. There are discussed the results of experimental studies of culverts made of metal corrugated pipes with a normal and spiral shape of corrugation the bottom of which is buried and filled with suitable granular material to the level of the natural channel of a small watercourse. It is established that when 10% of the area of the corrugated pipe is occupied by stone filling, its throughput is reduced by about 10-12%. Based on the review of the existing literature and the results of laboratory experiments, data is provided to estimate the values of the roughness coefficients of the composite cross-section of a single-point junction and directions for future research on culvert reclamation are outlined. Studying of the structure of the velocity distribution in culverts can lead to the improved conditions for fish passage without installing special structural elements in the transit path of the fish passage structure.

Sign in / Sign up

Export Citation Format

Share Document