Wire Drawing: Copper and Aluminium

2016 ◽  
pp. 37-85
Keyword(s):  
Wire Drawing

Microstructural Development in Nb-Ti Multifilamentary Superconductors During Processing

1985 ◽  
Vol 43 ◽  
pp. 190-191
Author(s):  
A. W. West
Keyword(s):  
Heat Treatment ◽  
Critical Current Density ◽  
Copper Matrix ◽  
Wire Drawing ◽  
Heat Treatments ◽  
Microstructural Development ◽  
Final Size ◽  
Density Values ◽  
The Wire ◽  
Multifilamentary Superconductors

The influence of the filament microstructure on the critical current density values, Jc, of Nb-Ti multifilamentary superconducting composites has been well documented. However the development of these microstructures during composite processing is still under investigation.During manufacture, the multifilamentary composite is given several heat treatments interspersed in the wire-drawing schedule. Typically, these heat treatments are for 5 to 80 hours at temperatures between 523 and 573K. A short heat treatment of approximately 3 hours at 573K is usually given to the wire at final size. Originally this heat treatment was given to soften the copper matrix, but recent work has shown that it can markedly change both the Jc value and microstructure of the composite.

Wire-drawing

1948 ◽  
Vol 27 (7) ◽  
pp. 333 ◽  
Author(s):  
H. Richards
Keyword(s):  
Wire Drawing

scholarly journals Laboratory-Scale Processing and Performance Assessment of Ti–Ta High-Temperature Shape Memory Spring Actuators

2021 ◽  
Author(s):  
A. Paulsen ◽  
H. Dumlu ◽  
D. Piorunek ◽  
D. Langenkämper ◽  
J. Frenzel ◽  
...  
Keyword(s):  
High Temperature ◽  
Shape Memory ◽  
Detrimental Effect ◽  
Wire Drawing ◽  
Fast Heating ◽  
Heating And Cooling ◽  
Arc Melting ◽  
Ω Phase ◽  
And Performance

AbstractTi75Ta25 high-temperature shape memory alloys exhibit a number of features which make it difficult to use them as spring actuators. These include the high melting point of Ta (close to 3000 °C), the affinity of Ti to oxygen which leads to the formation of brittle α-case layers and the tendency to precipitate the ω-phase, which suppresses the martensitic transformation. The present work represents a case study which shows how one can overcome these issues and manufacture high quality Ti75Ta25 tensile spring actuators. The work focusses on processing (arc melting, arc welding, wire drawing, surface treatments and actuator spring geometry setting) and on cyclic actuator testing. It is shown how one can minimize the detrimental effect of ω-phase formation and ensure stable high-temperature actuation by fast heating and cooling and by intermediate rejuvenation anneals. The results are discussed on the basis of fundamental Ti–Ta metallurgy and in the light of Ni–Ti spring actuator performance.

Benefits of Using Diamond Dies for Cold Alternate Drawing of Magnesium Alloys

2016 ◽  
Vol 716 ◽  
pp. 13-21 ◽  
Author(s):  
Vladimir Stefanov Hristov ◽  
Kazunari Yoshida
Keyword(s):  
Magnesium Alloy ◽  
Weight Ratio ◽  
High Strength ◽  
Wire Drawing ◽  
High Ductility ◽  
Element Analysis ◽  
The Wire ◽  
Shearing Strain ◽  
Drawing Method

In recent years, due to its low density and high strength/weight ratio, magnesium alloy wires has been considered for application in many fields, such as welding, electronics, medical field (for production of stents). But for those purposes, we need to acquire wires with high strength and ductility. For that we purpose we proposed alternate drawing method, which is supposed to highly decrease the shearing strain near the surface of the wire after drawing, by changing the direction of the wire drawing with each pass and thus acquiring high ductility wires.We have done research on the cold alternate drawing of magnesium alloy wires, by conducting wire drawing of several magnesium wires and testing their strength, hardness, structure, surface and also finite element analysis, we have proven the increase of ductility at the expense of some strength.In this research we are looking to further improve the quality of the drawn wires by examining the benefits of using diamond dies over tungsten carbine dies. Using the alternate drawing method reduces the strength of the drawn wires and thus lowering their drawing limit. By using diamond dies we are aiming to decrease the drawing stress and further increase the drawing limit of the alternate drawn wires and also improve the quality of the finishing surface of the wires. With this in mind we are aiming to produce a good quality wire with low diameter, high ductility, high strength and fine wire surface.

Research on the Wire Drawing Die Pass Parameter Calculation Based on the Least Square Algorithm

2012 ◽  
Vol 591-593 ◽  
pp. 850-853
Author(s):  
Huai Xing Wen ◽  
Yong Tao Yang
Keyword(s):  
Pore Structure ◽  
Least Squares ◽  
Least Squares Method ◽  
Piecewise Linear ◽  
Wire Drawing ◽  
Least Square ◽  
Structure Characteristics ◽  
Drawing Die ◽  
The Wire ◽  
Drawing Dies

Drawing Dies meter A / D acquisition module will be collected from the mold hole contour data to draw a curve in Matlab. According to the mold pore structure characteristics of the curve, the initial cut-off point of each part of contour is determined and iteratived optimization to find the best cut-off point, use the least squares method for fitting piecewise linear and fitting optimization to find the function of the various parts of the curve function, finally calculate the pass parameters of drawing mode. Parameters obtained compare with the standard mold, both of errors are relatively small that prove the correctness of the algorithm. Also a complete algorithm flow of pass parameters is designed, it can fast and accurately measure the wire drawing die hole parameters.

scholarly journals Validity of Matthiessen's Rule for Cold-worked Wires

1953 ◽  
Vol 6 (1) ◽  
pp. 116 ◽  
Author(s):  
W Boas ◽  
JF Nicholas
Keyword(s):  
Electrical Resistivity ◽  
Characteristic Temperature ◽  
Wire Drawing ◽  
Metals And Alloys ◽  
Nickel Copper ◽  
Aluminium Bronze ◽  
Cold Worked ◽  
Matthiessen's Rule ◽  
Matthiessen’S Rule

Matthiessen's rule has been tested by, determining the slopes of the electrical resistivity-temperature curves for wires of eight common metals and alloys in various states of deformation by wire-drawing. The results show that the slope is independent of deformation, i.e. the rule is true, to within 0�5 per cent. for nickel, copper (two purities), iron, and 80/20 brass, and to within 1 per cent. for aluminium. However, for 75/25 brass and an aluminium bronze, deformations corresponding to logarithmic strains of 2�3 decrease the slopes by 1 and 3 per cent. respectively. As an explanation of this behaviour, it is suggested that deformation causes an increase in the characteristic temperature.

Sign in / Sign up

Export Citation Format

Share Document