Post Weld Heat Treatment surface residual stress measurements using X-ray diffraction

2015 ◽  
pp. 563-567
Author(s):  
S Kumar ◽  
M Tan ◽  
B Wong ◽  
N Weeks
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Post Weld Heat Treatment ◽  
X Ray Diffraction ◽  
Surface Residual Stress ◽  
X Ray ◽  
Stress Measurements ◽  
Weld Heat

scholarly journals Optimization Study of Post-Weld Heat Treatment for 12Cr1MoV Pipe Welded Joint

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 127
Author(s):  
Zichen Liu ◽  
Xiaodong Hu ◽  
Zhiwei Yang ◽  
Bin Yang ◽  
Jingkai Chen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stress Reduction ◽  
Simulation Method ◽  
Post Weld Heat Treatment ◽  
Residual Stress Field ◽  
Element Analysis ◽  
Tempering Treatment ◽  
Temper Heat Treatment ◽  
Weld Heat

In order to clarify the role of different post-weld heat treatment processes in the manufacturing process, welding tests, post-weld heat treatment tests, and finite element analysis (FEA) are carried out for 12C1MoV steel pipes. The simulated temperature field and residual stress field agree well with the measured results, which indicates that the simulation method is available. The influence of post-weld heat treatment process parameters on residual stress reduction results is further analyzed. It is found that the post weld dehydrogenation treatment could not release residual stress obviously. However, the residual stress can be relieved by 65% with tempering treatment. The stress relief effect of “post weld dehydrogenation treatment + temper heat treatment” is same with that of “temper heat treatment”. The higher the temperature, the greater the residual stress reduction, when the peak temperature is at 650–750 °C, especially for the stress concentration area. The longer holding time has no obvious positive effect on the reduction of residual stress.

Service Loading Analysis of Wind Turbine Gearbox Rolling Bearings Based on X-Ray Diffraction Residual Stress Measurements

2013 ◽  
Vol 768-769 ◽  
pp. 723-732 ◽  
Author(s):  
Jürgen Gegner ◽  
Wolfgang Nierlich
Keyword(s):  
Residual Stress ◽  
Wind Turbine ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
X Ray Diffraction ◽  
Rolling Bearings ◽  
Wind Turbine Gearbox ◽  
X Ray ◽  
Stress Measurements

Rolling bearings in wind turbine gearboxes occasionally fail prematurely by so-called white etching cracks. The appearance of the damage indicates brittle spontaneous tensile stress induced surface cracking followed by corrosion fatigue driven crack growth. An X-ray diffraction based residual stress analysis reveals vibrations in service as the root cause. The occurrence of high local friction coefficients in the rolling contact is described by a tribological model. Depth profiles of the equivalent shear and normal stresses are compared with residual stress patterns and a relevant fracture strength, respectively. White etching crack failures are reproduced on a rolling contact fatigue test rig under increased mixed friction. Causative vibration loading is evident from residual stress measurements. Cold working compressive residual stresses are an effective countermeasure.

scholarly journals Residual Stress State of X65 Pipeline Girth Welds Before and After Local and Furnace Post Weld Heat Treatment

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Yao Ren ◽  
Anna Paradowska ◽  
Bin Wang ◽  
Elvin Eren ◽  
Yin Jin Janin
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Residual Stresses ◽  
Outer Surface ◽  
Post Weld Heat Treatment ◽  
Pipe Length ◽  
Stress Profiles ◽  
Girth Welds ◽  
Welded Pipe ◽  
Weld Heat

This research investigated the effects of global (in other words, furnace-based) and local post weld heat treatment (PWHT) on residual stress (RS) relaxation in API 5L X65 pipe girth welds. All pipe spools were fabricated using identical pipeline production procedures for manufacturing multipass narrow gap welds. Nondestructive neutron diffraction (ND) strain scanning was carried out on girth welded pipe spools and strain-free comb samples for the determination of the lattice spacing. All residual stress measurements were carried out at the KOWARI strain scanning instrument at the Australian Nuclear Science and Technology Organization (ANSTO). Residual stresses were measured on two pipe spools in as-welded condition and two pipe spools after local and furnace PWHT. Measurements were conducted through the thickness in the weld material and adjacent parent metal starting from the weld toes. Besides, three line-scans along pipe length were made 3 mm below outer surface, at pipe wall midthickness, and 3 mm above the inner surface. PWHT was carried out for stress relief; one pipe was conventionally heat treated entirely in an enclosed furnace, and the other was locally heated by a flexible ceramic heating pad. Residual stresses measured after PWHT were at exactly the same locations as those in as-welded condition. Residual stress states of the pipe spools in as-welded condition and after PWHT were compared, and the results were presented in full stress maps. Additionally, through-thickness residual stress profiles and the results of one line scan (3 mm below outer surface) were compared with the respective residual stress profiles advised in British Standard BS 7910 “Guide to methods for assessing the acceptability of flaws in metallic structures” and the UK nuclear industry's R6 procedure. The residual stress profiles in as-welded condition were similar. With the given parameters, local PWHT has effectively reduced residual stresses in the pipe spool to such a level that it prompted the thought that local PWHT can be considered a substitute for global PWHT.

Revision and extension of the standard laboratory technique for X-ray diffraction measurement of residual stress gradients

2007 ◽  
Vol 40 (4) ◽  
pp. 675-683 ◽  
Author(s):  
Cristy L. Azanza Ricardo ◽  
Mirco D'Incau ◽  
Paolo Scardi
Keyword(s):  
Residual Stress ◽  
Hole Drilling ◽  
Al Alloy ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Surface Residual Stress ◽  
X Ray ◽  
Stress Gradients ◽  
Layer Removal ◽  
Removal Technique

A new procedure is proposed to determine sub-surface residual stress gradients by laboratory X-ray diffraction measurements at different depths using a chemical layer-removal technique. The standard correction algorithm for stress relaxation due to layer removal is improved by including corrections for X-ray absorption, and by the addition of constraints imposed by the mechanical equilibrium conditions. Besides correcting the data,i.e.providing more reliable through-thickness residual stress trends, the proposed procedure also provides an elastically compatible and plausible estimate of the residual stress inside the component, well beyond the measured region. The application of the model is illustrated for a set of Al-alloy components shot-peened at different Almen intensities. Results are compared with those given by `blind hole drilling', which is an independent and partly destructive method.

Design Optimisation of a Ferritic Ring Weld Specimen Using FE Modelling

2009 ◽  
Author(s):  
Christopher M. Gill ◽  
Paul Hurrell ◽  
John Francis ◽  
Mark Turski
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Neutron Diffraction ◽  
Stress Field ◽  
Finite Element Modelling ◽  
Post Weld Heat Treatment ◽  
Stress Fields ◽  
Element Modelling ◽  
Weld Heat

This paper describes the design optimisation of an SA508 ferritic steel ring weld specimen using FE modelling techniques. The aim was to experimentally and analytically study the effect of post weld heat treatment upon a triaxial residual stress field. Welding highly constrained geometries, such as those found in some pressure vessel joints, can lead to the formation of highly triaxial stress fields. It is thought that application of post weld heat treatments will not fully relax hydrostatic stress fields. Therefore a ferritic multi-pass ring weld specimen was designed and optimised, using 2D finite element modelling, to generate a high magnitude triaxial stress field. The specimen thickness and weld-prep geometry was optimised to produce a large hydrostatic stress field and still allow efficient use of neutron diffraction to measure the residual stress. This paper reports the development of the test specimen geometry and compares the results of welding FE analysis and neutron diffraction measurements. Welding residual stresses were experimentally determined using neutron diffraction; both before post weld heat treatment. Three dimensional moving heat source weld finite element modelling has been used to predict the residual stresses generated by the welding process used. Finite element modelling examined the effect of phase transformation upon the residual stress field produced by welding. The relaxation of welding stresses by creep during post weld heat treatment has also been modelled. Comparisons between the modelled and measured as-welded residual stress profiles are presented. This work allows discussion of the effect of post weld heat treatment of triaxial stress fields and determines if finite element modelling is capable of correctly predicting the stress relaxation.

scholarly journals Pengaruh Waktu Penahanan pada Perlakuan Panas Paska Pengelasan terhadap Ketangguhan Sambungan Las Baja

2019 ◽  
Vol 13 (2) ◽  
pp. 80
Author(s):  
Muhamad Fitri ◽  
Bambang Sukiyono ◽  
Martua Limido Simanjuntak
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Local Heating ◽  
Post Weld Heat Treatment ◽  
Impact Testing ◽  
Holding Time ◽  
Aisi 4130 ◽  
The Impact ◽  
Holding Temperature ◽  
Weld Heat

One of the welding methods that is widely used today because it is easier to operate, more practical in its use, can be used for all welding positions and more efficient is called Shield Metal Arc Welding (SMAW). In this welding, the base metal and filler metal will experience thermal cycles which lead to local heating and cooling processes resulting in residual stress and distortion in the material. This residual stress must be removed because it causes a decrease in the mechanical properties of the material. The most widely used method is the thermal method that is by Post Weld Heat Treatment (PWHT). The success of The post-weld heat treatment in removing residual stresses in PWHT is influenced by the holding time. This study aims to examine the effect of holding time on heat treatment, on the weld toughness of steel. In this study, the type of welding used was SMAW welding, the material used was steel AISI 4130, the electrodes used were LB-7018-1 standard application and AWS classification A5.1 E7018-1. The test holding temperature is 650oC. The holding time of testing uses three variables, namely: 2.5 hours, 4.5 hours, 6.5 hours. The Impact testing is done by the Charpy method. From this study, the influence of holding time variation on PWHT holding temperature on the weld strength of AISI 4130 steel was obtained.

Sign in / Sign up

Export Citation Format

Share Document