- Finite Element Techniques for the Numerical Simulation of Two-Phase Flows with Mass Transport

2015 ◽  
pp. 372-391
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Mass Transport ◽  
Two Phase Flows ◽  
Two Phase

scholarly journals Simulation of the Effect of Oil Volume Fractions in an Oil-Water Flows Along a Circular Pipe: A Finite Element Approach

2018 ◽  
Vol 10 (5) ◽  
pp. 19
Author(s):  
Ferdusee Akter ◽  
Md. Bhuyan ◽  
Ujjwal Deb
Keyword(s):  
Finite Element ◽  
Volume Fraction ◽  
Fluid Velocity ◽  
Galerkin Approximation ◽  
Computational Domain ◽  
Two Phase Flows ◽  
Two Phase ◽  
Volume Fractions ◽  
Oil In Water ◽  
Element Approach

Two phase flows in pipelines are very common in industries for the oil transportations. The aim of our work is to observe the effect of oil volume fraction in the oil in water two phase flows. The study has been accomplished using a computational model which is based on a Finite Element Method (FEM) named Galerkin approximation. The velocity profiles and volume fractions are performed by numerical simulations and we have considered the COMSOL Multiphysics Software version 4.2a for our simulation. The computational domain is 8m in length and 0.05m in radius. The results show that the velocity of the mixture decreases as the oil volume fraction increases. It should be noted that if we gradually increase the volume fractions of oil, the fluid velocity also changes and the saturated level of the volume fraction is 22.3%.

The Research on Steering Fracture Numerical Simulation

2013 ◽  
Vol 734-737 ◽  
pp. 1488-1492
Author(s):  
Zhen Yu Liu ◽  
Li Hong Yao ◽  
Hu Zhen Wang ◽  
Cui Cui Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
Simulation Method ◽  
Production Performance ◽  
Phase Flow ◽  
Water Production ◽  
Two Phase ◽  
Fractured Well

The fractures after artificial steering fracturing appear in shades of curved surface. Aiming at the problem of steering fracture, in the paper, numerical simulation method under the condition of three-dimensional two-phase flow is presented based on finite element method. In this method, of steering fracture was achieved by adopting surface elements fractures and tetrahedron elements to describe formation. By numerical simulation, the change rule of oil and water production performance of steering fractures can be calculated, and then the steering fracture parameters can be optimized before fracturing. A new method was supplied for the numerical simulation of artificial fractured well.

Sharp numerical simulation of incompressible two-phase flows

2019 ◽  
Vol 391 ◽  
pp. 91-118 ◽  
Author(s):  
Maxime Theillard ◽  
Frédéric Gibou ◽  
David Saintillan
Keyword(s):  
Numerical Simulation ◽  
Two Phase Flows ◽  
Two Phase

Numerical simulation for two-phase flows using hybrid scheme

2007 ◽  
Vol 186 (2) ◽  
pp. 980-991 ◽  
Author(s):  
Jun Zhou ◽  
Li Cai ◽  
Jian-Hu Feng ◽  
Wen-Xian Xie
Keyword(s):  
Numerical Simulation ◽  
Hybrid Scheme ◽  
Two Phase Flows ◽  
Two Phase

Experimental Visualization and Numerical Simulation of Liquid-Gas Two-Phase Flows in a Horizontal Pipe

2017 ◽  
Author(s):  
Milad Darzi ◽  
Chanwoo Park
Keyword(s):  
Numerical Simulation ◽  
Gas Flow ◽  
Cfd Simulation ◽  
Glass Tube ◽  
Flow Patterns ◽  
Two Phase Flows ◽  
Two Phase ◽  
Mixture Flow ◽  
Horizontal Pipe ◽  
Flow Rates

This paper presents the results of both visualization experiment and numerical simulation for two-phase (water-air mixture) flows in a horizontal tube. A visualization experimental setup was used to observe various two-phase flow patterns for different flow rates of water/air mixture flow in a glass tube of 12 mm in diameter. Total of 303 experimental data points were compared with Mandhane’s flow map. Most of the data for stratified, plug and slug flows were found to be in good agreement. However, annular flow was observed for relatively lower gas flow rates and also wavy flow occurred at relatively higher liquid flow rates in this experiment. A three-dimensional Computational Fluid Dynamics (CFD) simulation was performed using OpenFOAM employing “interFoam” as the solver to simulate the two-phase flows in horizontal pipe based on Volume-Of-Fluid (VOF) method. The simulated and experimentally observed flow patterns for the same set of superficial velocities shows acceptable similarities for stratified, wavy, plug, slug and annular flows. Also, the computed values of the void fraction and pressure drop for the numerical simulations shows reasonable agreement with well-known correlations in literature.

Sign in / Sign up

Export Citation Format

Share Document