Damaged structures Statistics of still water bending moment of damaged ships

2015 ◽  
pp. 505-512
Keyword(s):  
Bending Moment

Influence of Yield Strength Variability over Cross-Section to Steel Beam Load-Carrying Capacity

2005 ◽  
Vol 10 (2) ◽  
pp. 151-160 ◽  
Author(s):  
J. Kala ◽  
Z. Kala
Keyword(s):  
Yield Strength ◽  
Cross Section ◽  
Carrying Capacity ◽  
Bending Moment ◽  
Statistical Characteristics ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Strength Variability ◽  
Hot Rolled ◽  
Hot Rolled Steel

Authors of article analysed influence of variability of yield strength over cross-section of hot rolled steel member to its load-carrying capacity. In calculation models, the yield strength is usually taken as constant. But yield strength of a steel hot-rolled beam is generally a random quantity. Not only the whole beam but also its parts have slightly different material characteristics. According to the results of more accurate measurements, the statistical characteristics of the material taken from various cross-section points (e.g. from a web and a flange) are, however, more or less different. This variation is described by one dimensional random field. The load-carrying capacity of the beam IPE300 under bending moment at its ends with the lateral buckling influence included is analysed, nondimensional slenderness according to EC3 is λ¯ = 0.6. For this relatively low slender beam the influence of the yield strength on the load-carrying capacity is large. Also the influence of all the other imperfections as accurately as possible, the load-carrying capacity was determined by geometrically and materially nonlinear solution of very accurate FEM model by the ANSYS programme.

Buckling Behavior of Tire Breaker Structure

1983 ◽  
Vol 11 (1) ◽  
pp. 3-19
Author(s):  
T. Akasaka ◽  
S. Yamazaki ◽  
K. Asano
Keyword(s):  
Elastic Foundation ◽  
Elastic Moduli ◽  
Wave Length ◽  
Bending Moment ◽  
Experimental Results ◽  
Automobile Tire ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Steel Cord ◽  
Interlaminar Shear

Abstract The buckled wave length and the critical in-plane bending moment of laminated long composite strips of cord-reinforced rubber sheets on an elastic foundation is analyzed by Galerkin's method, with consideration of interlaminar shear deformation. An approximate formula for the wave length is given in terms of cord angle, elastic moduli of the constituent rubber and steel cord, and several structural dimensions. The calculated wave length for a 165SR13 automobile tire with steel breakers (belts) was very close to experimental results. An additional study was then conducted on the post-buckling behavior of a laminated biased composite beam on an elastic foundation. This beam is subjected to axial compression. The calculated relationship between the buckled wave rise and the compressive membrane force also agreed well with experimental results.

Estimation of the severity of damage produced by a transverse crack

2020 ◽  
Vol 65 (1) ◽  
pp. 137-144
Author(s):  
Marius-Vasile Pop
Keyword(s):  
Transverse Crack ◽  
Bending Moment ◽  
Cantilever Beams ◽  
Trend Line ◽  
The Real ◽  
Symmetrical Deformation ◽  
Frequency Drop ◽  
Equidistant Points ◽  
Fixed End ◽  
Crack Position

This paper presents a method to find the severity of a crack for cantilever beams that can be used to estimate the frequency drop due to the crack. The severity is found for the crack located at the location where the biggest curvature (or bending moment) is achieved. Because the fixing condition does not permit a symmetrical deformation around the crack, the apparent severity is smaller as the real one. The latter is found by the estimated value of the trend-line at the fixed end, it being constructed on points that consider the crack position (equidistant points in the proximity of the fixed end) and the resulted deflections.

Issues on Design of Piled Raft Foundation

2018 ◽  
Vol 14 (1) ◽  
pp. 6057-6061 ◽  
Author(s):  
Padmanaban M S ◽  
J Sreerambabu
Keyword(s):  
Contact Area ◽  
Concrete Slab ◽  
Design Procedure ◽  
Bending Moment ◽  
Foundation Design ◽  
Detailed Review ◽  
Piled Raft ◽  
Piled Raft Foundation ◽  
Raft Foundation ◽  
Influencing Parameters

A piled raft foundation consists of a thick concrete slab reinforced with steel which covers the entire contact area of the structure, in which the raft is supported by a group of piles or a number of individual piles. Bending moment on raft, differential and average settlement, pile and raft geometries are the influencing parameters of the piled raft foundation system. In this paper, a detailed review has been carried out on the issues on the raft foundation design. Also, the existing design procedure was explained.

The Influence of Loads Superposition, Deterioration Due to Cracks and Residual Stresses on the Strength of Tubular Junction

2017 ◽  
Vol 68 (6) ◽  
pp. 1267-1273
Author(s):  
Valeriu V. Jinescu ◽  
Angela Chelu ◽  
Gheorghe Zecheru ◽  
Alexandru Pupazescu ◽  
Teodor Sima ◽  
...  
Keyword(s):  
Stress Concentration ◽  
Residual Stresses ◽  
Bending Moment ◽  
Combined Loading ◽  
Torsional Moment ◽  
Calculation Methods ◽  
State Of Stress ◽  
Cracked Structures ◽  
Total Participation ◽  
Theoretical Results

In the paper the interaction of several loads like pressure, axial force, bending moment and torsional moment are analyzed, taking into account the deterioration due to cracks and the influence of residual stresses. A nonlinear, power law, of structure material is considered. General relationships for total participation of specific energies introduced in the structure by the loads, as well as for the critical participation have been proposed. On these bases: - a new strength calculation methods was developed; � strength of tubular cracked structures and of cracked tubular junction subjected to combined loading and strength were analyzed. Relationships for critical state have been proposed, based on dimensionless variables. These theoretical results fit with experimental date reported in literature. On the other side stress concentration coefficients were defined. Our one experiments onto a model of a pipe with two opposite nozzles have been achieved. Near one of the nozzles is a crack on the run pipe. Trough the experiments the state of stress have been obtained near the tubular junction, near the tip of the crack and far from the stress concentration points. On this basis the stress concentration coefficients were calculated.

Sign in / Sign up

Export Citation Format

Share Document