Dual-Fuel Engine Operation on Alternative Fuels

2015 ◽  
pp. 258-279
Keyword(s):  
Alternative Fuels ◽  
Dual Fuel ◽  
Engine Operation

scholarly journals Combustion Stability, Performance and Emission Characteristics of a CI Engine Fueled with Diesel/n-Butanol Blends

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2817
Author(s):  
Arkadiusz Jamrozik ◽  
Wojciech Tutak ◽  
Karol Grab-Rogaliński
Keyword(s):  
Alternative Fuels ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Initial Increase ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Energy Share

The development of compression ignition engines depends mainly on using alternative fuels, such as alcohols. The paper presents the results of tests of a stationary compression ignition engine fueled with mixtures of diesel oil and n-butanol with an energy share from 0 to 60%. The combustion and emission results of a dual-fuel engine were compared to a conventional diesel-only engine. As part of the work, the combustion process, including changes in pressure and heat release rate, as well as exhaust emissions from the test engine, were investigated. The main operational parameters of the engine were determined, including mean indicated pressure, thermal efficiency and specific energy consumption. Moreover, the stability of the engine operation was analyzed. The research shows that the 60% addition of n-butanol to diesel fuel increases the ignition delay (by 39%) and shortens the combustion duration (by 57%). In addition, up to 40%, it results in increased pmax, HRRmax and PPRmax. The engine was characterized by the highest efficiency, equal to 41.35% when operating on DB40. In the whole range of alcohol content, the dual-fuel engine was stable. With the increase of n-butanol content to 40%, the emission of NOx increased. The lowest concentration of CO was obtained during the combustion of DB50. After the initial increase (for DB20), the THC emission was reduced to the lowest value for DB40. Increasing the energy share of alcohol to 60% resulted in a significant, more than 43 times, reduction in soot emissions.

scholarly journals INVESTIGATION ON THE AIR-GAS CHARACTERISTICS OF AIR-HYDROGEN MIXER DESIGNED FOR DUAL FUEL – ENGINES

2021 ◽  
pp. 66-77
Author(s):  
Alaulddin A. Kazum ◽  
Osam H. Attia ◽  
Ali I. Mosa ◽  
Nor Mariah. Adam
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Alternative Fuels ◽  
Dual Fuel ◽  
Engine Operation ◽  
Friction Forces ◽  
Fuel Ratio ◽  
Head Surface ◽  
Wide Range ◽  
Reduce Emissions

High smoke emissions, nitrogen oxide and particulate matter typically produced by diesel engines. Diminishing the exhausted emissions without doing any significant changes in their mechanical configuration is a challenging subject. Thus, adding hydrogen to the traditional fuel would be the best practical choice to ameliorate diesel engines performance and reduce emissions. The air hydrogen mixer is an essential part of converting the diesel engine to work under dual fuel mode (hydrogen-diesel) without any engine modification. In this study, the Air-hydrogen mixer is developed to get a homogenous mixture for hydrogen with air and a stoichiometric air-fuel ratio according to the speed of the engine. The mixer depends on the balance between the force exerted on the head surface of the valve and the opposite forces (the spring and friction forces) and its relation to decrease and increase the fuel inlet. Computational fluid dynamics (CFD) analysis software was utilised to study the hydrogen and airflow behaviour inside the mixer, established by 3.2 L engine. The Air-hydrogen mixer is examined with different speeds of engine1000, 2000, 3000 and 4000 RPM. Results showed air-hydrogen mixture was homogenous in the mixer. Furthermore, the stoichiometric air-fuel ratio was achieved according to the speed of the engine, the developed mixer of the AIR-Hydrogen mixing process provides high mixing homogeneity and engines with stoichiometric air-fuel ratios, which subsequently contributes to the high levels of efficiency in engine operation. In summary, the current study intends to reduce the emissions of gases and offer a wide range of new alternative fuels usage. While the performance of the diesel engine with the new air-hydrogen mixer needs to be tested practically.

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Comparative assessment of engine vibration, combustion, performance and emission characteristics between single and twin-cylinder diesel engines in unifuel and dual-fuel mode

2021 ◽  
pp. 1-39
Author(s):  
Akash Chandrabhan Chandekar ◽  
Sushmita Deka ◽  
Biplab K. Debnath ◽  
Ramesh Babu Pallekonda
Keyword(s):  
Natural Gas ◽  
Alternative Fuels ◽  
Load Condition ◽  
Alternative Fuel ◽  
Dual Fuel ◽  
Cylinder Pressure ◽  
Compressed Natural Gas ◽  
Single Cylinder ◽  
Engine Vibration ◽  
Single Cylinder Engine

Abstract The persistent efforts among the researchers are being done to reduce emissions by the exploration of different alternative fuels. The application of alternative fuel is also found to influence engine vibration. The present study explores the potential connection between the change of the engine operating parameters and the engine vibration pattern. The objective is to analyse the effect of alternative fuel on engine vibration and performance. The experiments are performed on two different engines of single cylinder and twin-cylinder variants at the load range of 0 to 34Nm, with steps of 6.8Nm and at the constant speed of 1500rpm. The single cylinder engine, fuelled with only diesel mode, is tested at two compression ratios of 16.5 and 17.5. While, the twin-cylinder engine with a constant compression ratio of 16.5, is tested at both diesel unifuel and diesel-compressed natural gas dual-fuel modes. Further, in dual-fuel mode, tests are conducted with compressed natural gas substitutions of 40%, 60% and 80% for given loads and speed. The engine vibration signatures are measured in terms of root mean square acceleration, representing the amplitude of vibration. The combustion parameters considered are cylinder pressure, rate of pressure rise, heat release rate and ignition delay. At higher loads, the vibration amplitude increases along with the cylinder pressure. The maximum peak cylinder pressure of 95bar is found in the case of the single cylinder engine at the highest load condition that also produced a peak vibration of 3219m/s2.

scholarly journals Research on Fuel Efficiency and Emissions of Converted Diesel Engine with Conventional Fuel Injection System for Operation on Natural Gas

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2413 ◽  
Author(s):  
Lebedevas ◽  
Pukalskas ◽  
Daukšys ◽  
Rimkus ◽  
Melaika ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Natural Gas ◽  
Fuel Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Fuel Injection System ◽  
Significant Deterioration ◽  
Engine Operation ◽  
Conventional Fuel

This paper presents a study on the energy efficiency and emissions of a converted high-revolution bore 79.5 mm/stroke 95 mm engine with a conventional fuel injection system for operation with dual fuel feed: diesel (D) and natural gas (NG). The part of NG energy increase in the dual fuel is related to a significant deterioration in energy efficiency (ηi), particularly when engine operation is in low load modes and was determined to be below 40% of maximum continuous rating. The effectiveness of the D injection timing optimisation was established in high engine load modes within the range of a co-combustion ratio of NG ≤ 0.4: with an increase in ηi, compared to D, the emissions of NOx+ HC decreased by 15% to 25%, while those of CO2 decreased by 8% to 16%; the six-fold CO emission increase, up to 6 g/kWh, was unregulated. By referencing the indicated process characteristics of the established NG phase elongation in the expansion stroke, the combustion time increase as well as the associated decrease in the cylinder excess air ratio (α) are possible reasons for the increase in the incomplete combustion product emission.

Shock Tube Autoignition Studies for Conventional and Alternative Transportation Fuel Components

2012 ◽  
Author(s):  
Matthew A. Oehlschlaeger
Keyword(s):  
Shock Tube ◽  
Reaction Kinetics ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
High Pressures ◽  
Rapid Development ◽  
Oxidation Kinetic ◽  
Engine Operation ◽  
Alternative Transportation ◽  
Fuel Components

Gas-phase autoignition, a fundamental indicator of fuel reactivity, and its underlying reaction kinetics are of importance to the operation of gas turbine and internal combustion engines, particularly in advanced engine concepts where kinetics may play a more important role than in legacy designs. The increasing significance of kinetics in modern engine operation and the rapid development of alternative fuels motivates an understanding of reaction kinetics and in particular the influence of fuel structure on oxidation and autoignition. A series of shock tube autoignition studies have been carried for pure fuel components found in conventional and alternative transportation fuels over the last five years. Results of these studies are summarized here. Measurements have been made for compounds found in or relevant to conventional gasoline, diesel, and jet fuels and alternative fuels including biodiesels, Fischer-Tropsch fuels, and hydroprocessed renewable fuels. Experiments were carried out for gaseous fuel/air mixtures in a heated shock tube facility. Fuel/air mixtures were studied for rich to lean conditions at high pressures (10–60 atm) and for a large range of temperatures spanning three distinct regions of reactivity from the high-temperature Arrhenius region, through the negative-temperature-coefficient region, and into the low-temperature region. The experimental results provide fundamental information about the structure-reactivity relationships for fuels and targets for the development of fuel oxidation kinetic models.

Effect of Water Injection in Acetylene-Diesel Dual Fuel DI Diesel Engine

2012 ◽  
Author(s):  
T. Lakshmanan ◽  
A. Khadeer Ahmed ◽  
G. Nagarajan
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Alternative Fuels ◽  
Gas Flow ◽  
Water Injection ◽  
Intake Manifold ◽  
Dual Fuel ◽  
Intake Port ◽  
Gas Temperature ◽  
Brake Thermal Efficiency

Gaseous fuels are good alternative fuels to improve the energy crisis of today’s situation due to its clean burning characteristics. However, the incidence of backfire and knock remains a significant barrier in commercialization. With the invention of latest technology, the above barriers are eliminated. One such technique is timed injection of water into the intake port. In the present investigation, acetylene was aspirated in the intake manifold of a single cylinder diesel engine, with a gas flow rate of 390 g/h, along with water injected in the intake port, to overcome the backfire and knock problems in gaseous dual fuel engine. The brake thermal efficiency and emissions such as NOx, smoke, CO, HC, CO2 and exhaust gas temperature were studied. Dual fuel operation of acetylene induction with injection of water results in lowered NOx emissions with complete elimination of backfire and knock at the expense of brake thermal efficiency.

Performance, Emission Characteristics of Dual Fuel Engine Fuelled with Brown Briquette Biomass and Rice bran Oil Biodiesel

2020 ◽  
Vol 12 (4) ◽  
Author(s):  
K.M. Nataraja ◽  
N.R. Banapurmath ◽  
V.S. Yaliwal ◽  
Nandish Mathad
Keyword(s):  
Rice Bran ◽  
Rice Bran Oil ◽  
Agricultural Waste ◽  
Dual Fuel ◽  
Producer Gas ◽  
Fuel Saving ◽  
Engine Operation ◽  
Downdraft Gasifier ◽  
Pilot Fuel ◽  
Operation Results

In this work agricultural waste-based coconut biomass and compressed agricultural waste derived from brown briquette were used for generation of gas in a downdraft gasifier. Its subsequent combustion takes place in a modified diesel engine using rice bran oil (RiOME) biodiesel injected in bi-fuel mode. For the injected pilot fuel, producer gas operation with coconut biomass derived fuel has improved liquid fuel saving. Downdraft gasifier was integrated with four stroke DI water cooled 5.2 kW CI engine at 1500 rpm speed. Experimentation results showed that for the gasifierengine system coconut biomass derived gas with diesel based dual fuel operation results in 9.05% higher BTE. RiOME producer gas (CNS) operation showed 16.1% decrease in EGT and 12.1% reduction in NOx emission compared to diesel based dual fuel operation. NOx emissions for the RiOME based engine operation were found to be lower than the diesel based operation. However, the smoke, HC and CO emissions were higher. Diesel fuel saving about 56% was achieved by diesel and producer gas (CNS) dual fuel operation and 100% biofuel utilization in RiOME -producer gas bi-fuel mode of operation was achieved. Further, heat release rates and cylinder pressure for RiOME producer gas (CNS) was marginally lesser than diesel operation.

Sign in / Sign up

Export Citation Format

Share Document