Optimization of the ultimate capacity of a reinforced concrete slab bridge

2014 ◽  
pp. 923-927
Author(s):  
D Novák ◽  
O Slowik ◽  
R Pukl
Keyword(s):  
Reinforced Concrete ◽  
Concrete Slab ◽  
Ultimate Capacity ◽  
Reinforced Concrete Slab

Dimension and Frequency Profiles of Concrete Highway Bridges in New Madrid Region of Southeastern Missouri

1997 ◽  
Vol 1594 (1) ◽  
pp. 84-93 ◽  
Author(s):  
Ralph Alan Dusseau
Keyword(s):  
Reinforced Concrete ◽  
Concrete Slab ◽  
Highway Bridges ◽  
Ambient Vibration ◽  
Earthquake Hazards ◽  
Empirical Formulas ◽  
Reinforced Concrete Slab ◽  
Box Girder ◽  
Bridge Spans ◽  
New Madrid

The results of a study funded by the U.S. Geological Survey as part of the National Earthquake Hazards Reduction Program are presented. The first objective of this study was the development of a database for all 211 highway bridges along I-55 in the New Madrid region of southeastern Missouri. Profiles for five key dimension parameters (which are stored in the database) were developed, and the results for concrete highway bridges are presented. The second objective was to perform field ambient vibration analyses on 25 typical highway bridge spans along the I-55 corridor to determine the fundamental vertical and lateral frequencies of the bridge spans measured. These 25 spans included six reinforced concrete slab spans and two reinforced concrete box-girder spans. The third objective was to use these bridge frequency results in conjunction with the dimension parameters stored in the database to develop empirical formulas for estimating bridge fundamental natural frequencies. These formulas were applied to all 211 Interstate highway bridges in southeastern Missouri. Profiles for both fundamental vertical and lateral frequencies were then developed, and the results for concrete highway bridges are presented.

An Assessment of the Long-Term Durability of Concrete in Radioactive Waste Repositories

1985 ◽  
Vol 50 ◽  
Author(s):  
A. Atkinson ◽  
D. J. Goult ◽  
J. A. Hearne
Keyword(s):  
Reinforced Concrete ◽  
Radioactive Waste ◽  
Concrete Slab ◽  
Laboratory Studies ◽  
Preliminary Assessment ◽  
Reinforced Concrete Slab ◽  
Radioactive Waste Repositories ◽  
Waste Repositories ◽  
Durability Of Concrete

AbstractA preliminary assessment of the long-term durability of concrete in a repository sited in clay is presented. The assessment is based on recorded experience of concrete structures and both field and laboratory studies. It is also supported by results of the examination of a concrete sample which had been buried in clay for 43 years.The enoineering lifetime of a 1 m thick reinforced concrete slab, with one face in contact with clay, and the way in which pH in the repository as a whole is likely to vary with time have both been estimated from available data. The estimates indicate that engineering lifetimes of about 103 years are expected (providing that sulphate resisting cement is used) and that pH is likely to remain above 10.5 for about 106 years.

Computer Nonlinear Analysis of the Formation and Development of Cracks in a Reinforced Concrete Slab Loaded by a Planar Uniform Load

2014 ◽  
Vol 606 ◽  
pp. 229-232 ◽  
Author(s):  
Petr Tej ◽  
Vítězslav Vacek ◽  
Jiří Kolísko ◽  
Jindřich Čech
Keyword(s):  
Reinforced Concrete ◽  
Ground Water ◽  
Nonlinear Analysis ◽  
Concrete Slab ◽  
Lower Surface ◽  
Uniform Load ◽  
Reinforced Concrete Slab

The paper focuses on a computer nonlinear analysis of the formation and development of cracks in a concrete slab exposed to a uniform continuous load on the lower surface. The analysis is based on an actual example of the formation and development of cracks in a basement slab exposed to ground water buoyancy.

Evaluation of Fatigue Damage in Reinforced Concrete Slab by Acoustic Emission.

1999 ◽  
pp. 251-259
Author(s):  
Shigenori YUYAMA ◽  
Zhang-Wang LI ◽  
Takeshi TOMOKIYO ◽  
Masaru YOSHIZAWA ◽  
Taketo UOMOTO
Keyword(s):  
Acoustic Emission ◽  
Reinforced Concrete ◽  
Fatigue Damage ◽  
Concrete Slab ◽  
Reinforced Concrete Slab

Experimental Study on Earth Pressure of Corrugated Steel Culvert under High Fill Embankment

2013 ◽  
Vol 405-408 ◽  
pp. 1815-1819
Author(s):  
Wen Sheng Yu ◽  
Zhu Long Li ◽  
Xiao Ru Xie ◽  
Li Yuan Guo
Keyword(s):  
Mechanical Property ◽  
Experimental Study ◽  
Reinforced Concrete ◽  
Concrete Slab ◽  
Earth Pressure ◽  
Reinforced Concrete Slab ◽  
The Earth ◽  
Filling Height ◽  
Test Points ◽  
Better Than

To analyze the earth pressure of corrugated steel culvert under high fill embankment, a field test was taken and the change law was got with the filling height increasing, the force state when geotechnical grilles were laid on the top of corrugated steel culvert was compared to that of reinforced concrete slab culvert. Results show that the pressure on the top of corrugated steel culvert is smaller than that on the external in same level when test points are near to culvert, the values of test points above and below geotechnical grilles are close, and the pressure of corrugated steel culvert is smaller than that of reinforced concrete slab culvert when filling height is above 7.3 m. So analysis indicates corrugated steel culvert spreads the upper load better, the geotechnical grille can reduce the pressure effectively through earth pressure redistribution, and the mechanical property of corrugated steel culvert is better than reinforced concrete slab culvert under high fill embankment.

Tame Valley Viaduct Assessment and Strengthening

2016 ◽  
Author(s):  
Sarah Jane Blick ◽  
Chris West
Keyword(s):  
Reinforced Concrete ◽  
Design Process ◽  
Composite Structure ◽  
Concrete Slab ◽  
City Centre ◽  
Box Girders ◽  
Reinforced Concrete Slab ◽  
Current Loading ◽  
The Web

Tame Valley Viaduct is a 620m long multi-span highway structure linking Birmingham city centre to the M6 motorway. An assessment in 2004 found the capacity of the structure to be inadequate for current loading, resulting in a requirement for strengthening. Before strengthening works were designed, a comprehensive, refined re-assessment of the structure was undertaken to fully define which areas needed strengthening and which did not. The composite structure comprises a reinforced-concrete slab and typically four longitudinal steel box girders. Each of these longitudinal girders comprises approximately 600 sets of web and flange panels. The scale of the task required automation of the assessment and design process. This paper discusses how the automation was undertaken including the preparation of models to calculate individual panel loading, assessment of the web and flange panels, and the checking of strengthening solutions.

Sign in / Sign up

Export Citation Format

Share Document