Surface protection methods and materials

2014 ◽  
pp. 401-488
Keyword(s):  
Surface Protection

scholarly journals Microstructural Charactistics of Plasma Sprayed NiCrBSi Coatings and Their Wear and Corrosion Behaviors

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 170
Author(s):  
Songqiang Huang ◽  
Jingzhong Zhou ◽  
Kuoteng Sun ◽  
Hailiang Yang ◽  
Weichen Cai ◽  
...  
Keyword(s):  
Laser Scanning ◽  
Acid Corrosion ◽  
Composite Coatings ◽  
Atmospheric Plasma ◽  
Confocal Laser ◽  
Formation Mechanisms ◽  
Temperature Oxidation ◽  
Surface Protection ◽  
Plasma Sprayed ◽  
Nicrbsi Coatings

Nickel-based alloys are commonly used as protective coating materials for surface protection applications owing to their superior resistance to corrosion, wear and high-temperature oxidation. It is urgent to study the fundamental mechanism between the structure and corrosion properties of the Nickel-base composite coatings. This paper, therefore, focuses on clarifying the mechanisms of the microstructure influencing the acid corrosion and mechanical characteristics of the as-sprayed NiCrBSi coating and post-heat-treated coating. The formation mechanisms of the amorphous phase of flat particles during the plasma spray process were studied by using X-ray diffraction analysis, Raman spectroscopy and confocal laser scanning microscope at first. Then the evolutionary process of the corrosion structure and phase of the coating in the accelerated corrosion experiment is directly visualized by using scanning electron microscopy and energy spectrum analysis. The mechanical properties of the amorphous NiCrBSi coatings are lastly measured by microhardness and friction wear tests. The critical phenomena and results help to elucidate the relative influence of the surface features of atmospheric plasma sprayed coatings on acid corrosion responses and wear resistance, aiming at contributing to the development of a protective technique for electrical engineering.

scholarly journals Use of Ecofriendly Glass Powder Concrete in Construction of Wind Farms

2021 ◽  
Vol 11 (7) ◽  
pp. 3050
Author(s):  
Eva M. García del Toro ◽  
Daniel Alcala-Gonzalez ◽  
María Isabel Más-López ◽  
Sara García-Salgado ◽  
Santiago Pindado
Keyword(s):  
Wind Farm ◽  
Glass Powder ◽  
Wind Farms ◽  
Main Element ◽  
Partial Replacement ◽  
Surface Protection ◽  
Air Content ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Rate Of Substitution

Silicon is the main element in the composition of glass and it has been seen that it can be used as a partial replacement for cement in the manufacture of concrete. Different dosages of glass powder and cement were applied to manufacture the concrete mixes. Initially, the characteristics of fresh concrete were studied, such as consistency, air content, apparent density and workability. Secondly, compressive strength tests were performed on the different concrete mixtures produced. The consistency tests allowed us to classify these concretes within the group of fluids. The air content of these concretes increased with the rate of substitution of cement by glass powder, resulting in lighter concretes. Density tests showed that this parameter decreased as the rate of substitution of cement increased. A coefficient k has been calculated for the substitution of glass powder by cement in the binder, using the Bolomey formula. Also, a mathematical model has been proposed to further analyze the experimental data. Major contributions of this work were to study the possible application of this concrete in different dispersions as a surface protection layer against the action of corrosion, in wind turbine foundations as well as the stabilization of the wind farm roads.

scholarly journals Spilanthes acmella Leaves Extract for Corrosion Inhibition in Acid Medium

Coatings ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 106
Author(s):  
Akbar Ali Samsath Begum ◽  
Raja Mohamed Abdul Vahith ◽  
Vijay Kotra ◽  
Mohammed Rafi Shaik ◽  
Abdelatty Abdelgawad ◽  
...  
Keyword(s):  
Mild Steel ◽  
Corrosion Inhibition ◽  
Active Sites ◽  
Inhibition Efficiency ◽  
Electrochemical Impedance ◽  
Film Formation ◽  
Protective Film ◽  
Surface Protection ◽  
Tafel Polarization ◽  
Spilanthes Acmella

In the present study, the corrosion inhibition effect of Spilanthes acmella aqueous leaves extract (SA-LE) on mild steel was investigated in 1.0 M HCl solution at different temperature using weight loss, Tafel polarization, linear polarization resistance (LPR), and electrochemical impedance (EIS) measurements. Adsorption of inhibitor on the surface of the mild steel obeyed both Langmuir and Temkin adsorption isotherms. The thermodynamic and kinetic parameters were also calculated to determine the mechanism of corrosion inhibition. The inhibition efficiency was found to increase with an increase in the inhibitor concentration i.e., Spilanthes acmella aqueous leaves extract, however, the inhibition efficiency decreased with an increase in the temperature. The phytochemical constituents with functional groups including electronegative hetero atoms such as N, O, and S in the extract adsorbed on the metal surface are found responsible for the effective performance of the inhibitor, which was confirmed by Fourier-transform infrared spectroscopy (FT-IR) and ultraviolet–visible spectroscopic (UV-Vis) studies. Protective film formation against corrosion was confirmed by scanning electron microscopy (SEM), atomic force microscopy (AFM), and contact angle studies. The result shows that the leaves extract acts as corrosion inhibitor and is able to promote surface protection by blocking active sites on the metal.

scholarly journals Laboratory Study of Deformation Behaviour of Two New Reinforcing Polymeric TSLs and Their Potential Application in Deep Underground Coal Mine

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2205
Author(s):  
Han Liang ◽  
Jun Han ◽  
Chen Cao ◽  
Shuangwen Ma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Underground Mining ◽  
Deformation Behaviour ◽  
Polymer Materials ◽  
Surface Protection ◽  
Steel Mesh ◽  
Geological Conditions ◽  
Deep Underground ◽  
Roadway Support

Thin spray-on liner (TSL) is a surface protection technology used by spraying a polymer film, which is widely used for mine airtightness and waterproofing. A reinforcing TSL can replace steel mesh, which is a new method for roadway support. This paper reviews the development of a reinforcing TSL. Considering the deterioration of geological conditions in deep underground mining and the demand for reinforcing automation, two kinds of polymeric reinforcing TSL (RPTSL) materials are developed. The mechanical characteristics of the new TSL materials are studied experimentally. Results show that the average compressive strength, tensile strength, cohesion, and internal friction angle of the two TSL materials are 52 and 32 MPa, 12 and 8 MPa, 6.2 and 17.2 MPa, and 33.6° and 25.9°, respectively. The bonding strength between the two materials and coal is greater than the tensile strength of coal itself, and the mechanical properties of the material for comparison are lower than those of both materials. Based on the TSL support mechanism, we examine the application of the two TSL materials to the mining environment and compare the mechanical properties of polymer materials and cement-based materials. The advantages of polymer materials include versatile mechanical properties, good adhesion, and high early strength. This study provides a new support material to replace steel mesh for roadway surface support, which satisfies the needs of different surface support designs under complex geological conditions, and promotes the automation of roadway support.

scholarly journals Enhancing the Ecological Value of Sea Dikes

Water ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1617 ◽  
Author(s):  
Scheres ◽  
Schüttrumpf
Keyword(s):  
Climate Change ◽  
Climate Change Adaptation ◽  
Interdisciplinary Collaboration ◽  
Ecological Value ◽  
Protection Measures ◽  
Surface Protection ◽  
Societal Needs ◽  
Ecological Aspects ◽  
The World ◽  
Sea Dikes

Sea dikes protect low-lying hinterlands along many coasts all around the world. Commonly, they are designed as embankments with grass covers or grey revetments accounting for the prevailing hydraulic loads. So far, incorporation of ecological aspects in the dike design is limited. With regard to increasing environmental awareness and climate change adaptation needs, the present study reviews methods for ecological enhancement of sea dikes and discusses limitations and challenges related to these methods. In doing so, one key aspect is to maintain dike safety while increasing the ecological value. Potential for ecological enhancement of sea dikes has been found regarding natural or nature-based solutions in the foreshore, dike surface protection measures (vegetated dike covers, hard revetments and dike roads) and the dike geometry. While natural and nature-based solutions in the foreland are investigated thoroughly, so far only few experiences with ecological enhancements of the dike structure itself were gained resulting in uncertainties and knowledge gaps concerning the implementation and efficiency. Additional to technical uncertainties, engineers and ecologists meet the challenge of interdisciplinary collaboration under consideration of societal needs and expectations.

scholarly journals Stable and tunable plasmon resonance of molybdenum oxide nanosheets from the ultraviolet to the near-infrared region for ultrasensitive surface-enhanced Raman analysis

2019 ◽  
Vol 10 (25) ◽  
pp. 6330-6335 ◽  
Author(s):  
Jinhu Wang ◽  
Yinhua Yang ◽  
Hua Li ◽  
Jun Gao ◽  
Ping He ◽  
...  
Keyword(s):  
Near Infrared ◽  
Infrared Region ◽  
Raman Analysis ◽  
Surface Protection ◽  
Surface Enhanced ◽  
Color Tunable ◽  
Surface Enhanced Raman ◽  
Heavily Doped ◽  
Near Infrared Region ◽  
Preparation Strategy

Preparation of color-tunable and stable plasmonic MoO3 nanomaterials remains challenging, due to the lack of an effective preparation strategy and surface protection in heavily doped MoO3.

Research and Manufacture of Nano-Silver Conductive Ink

2010 ◽  
Vol 174 ◽  
pp. 405-408 ◽  
Author(s):  
Bao Lin Tang ◽  
Guang Xue Chen ◽  
Qi Feng Chen ◽  
Jing Lei Tai
Keyword(s):  
Chemical Reduction ◽  
Nitrate Solution ◽  
Acrylic Resin ◽  
Silver Nitrate Solution ◽  
Nano Particles ◽  
Conductive Ink ◽  
Surface Protection ◽  
Nano Silver ◽  
Conductive Fillers ◽  
Liquid Chemical

Printing electronics technology promotes the application of conductive ink. In this paper, the manufacture of nano-sliver conductive ink is investigated. First, Spherical silver nano-particles were reduced from silver nitrate solution by liquid chemical reduction method, with hydrazine hydrate as reductant and PVP as surface-protection reagent. SEM was used to characterize the morphology of silver powders, and the mean particles size is 62.79 nm. Then, conductive ink was prepared with nano-silver particles made in this research as conductive fillers, polyurethane resin and acrylic resin as binders, and stearic acid as dispersant. In the last, the conductive ink was printed on the PCB substrate by screening printing. After the ink is dried, conductivity, abrasion resistance, and adhesion were tested. The experiment results shows that the order of sheet resistivity magnitude is 10-4Ω•m, the number of rubbing fastness is more than 6000, and the adhesion can be resisted repeatedly to tape tear.

scholarly journals Outline of Recommendation for Concrete Repair and Surface Protection of Concrete Structures by JSCE

2005 ◽  
Vol 43 (11) ◽  
pp. 3-11 ◽  
Author(s):  
I. Funakawa ◽  
S. Ushijima ◽  
T. Miyagawa ◽  
Y. Yamamoto
Keyword(s):  
Concrete Structures ◽  
Concrete Repair ◽  
Surface Protection
Sign in / Sign up

Export Citation Format

Share Document