Control the Flow Curve of the Thermoplastic Vulcanized (PE/PB)

2012 ◽  
pp. 97-104
Keyword(s):  
Flow Curve

Absorption of oxygen into solutions of polymers

1986 ◽  
Vol 51 (10) ◽  
pp. 2127-2134 ◽  
Author(s):  
František Potůček ◽  
Jiří Stejskal
Keyword(s):  
Mass Transfer ◽  
Aqueous Solutions ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Flow Rate ◽  
Liquid Flow ◽  
Flow Curve ◽  
Liquid Flow Rate ◽  
Polymer Concentration ◽  
Newtonian Liquids

Absorption of oxygen into water and aqueous solutions of poly(acrylamides) was studied in an absorber with a wetted sphere. The effects of changes in the liquid flow rate and the polymer concentration on the liquid side mass transfer coefficient were examined. The results are expressed by correlations between dimensionless criteria modified for non-Newtonian liquids whose flow curve can be described by the Ostwald-de Waele model.

Rotational rheometry of liquid metal systems: Measurement geometry selection and flow curve analysis

2010 ◽  
Vol 165 (13-14) ◽  
pp. 733-742 ◽  
Author(s):  
Mohammad Minhajuddin Malik ◽  
Manickaraj Jeyakumar ◽  
Mohamed S. Hamed ◽  
Michael J. Walker ◽  
Sumanth Shankar
Keyword(s):  
Liquid Metal ◽  
Flow Curve ◽  
Curve Analysis ◽  
Measurement Geometry

scholarly journals Shear thickening behavior in dense repulsive and attractive suspensions of hard spheres

Soft Matter ◽  
2021 ◽  
Author(s):  
Vikram Rathee ◽  
Alessandro Monti ◽  
Marco Edoardo Rosti ◽  
Amy Q Shen
Keyword(s):  
Flow Curve ◽  
Hard Spheres ◽  
Shear Thickening ◽  
Colloidal Suspensions ◽  
Thickening Behavior ◽  
The Stability

Shear thickening in stable dense colloidal suspensions is a reversible phenomenon and no hysteresis is observed in the flow curve measurements. However, a reduction in the stability of colloids promotes...

Estimation of Red Cell Deformability Based on Flow Curve of Whole Blood in the Higher Shear Rate Range.

2001 ◽  
Vol 27 (2) ◽  
pp. 228-235
Author(s):  
Shinichi Ookawara ◽  
Akihisa Yano ◽  
Kohei Ogawa ◽  
Koichi Taniguchi
Keyword(s):  
Shear Rate ◽  
Whole Blood ◽  
Flow Curve ◽  
Red Cell ◽  
Cell Deformability ◽  
Red Cell Deformability ◽  
Rate Range

Effects of Blade Outlet Width on Flow Field and Characteristic of Centrifugal Pumps

2009 ◽  
Author(s):  
Ming-gao Tan ◽  
Hou-lin Liu ◽  
Shou-qi Yuan ◽  
Yong Wang ◽  
Kai Wang
Keyword(s):  
Flow Field ◽  
Flow Curve ◽  
High Efficiency ◽  
Field Analysis ◽  
Centrifugal Pumps ◽  
Research Results ◽  
Rotor Stator Interaction ◽  
Nominal Condition ◽  
Specific Speed ◽  
Width Change

The present deficiency about numerical simulation research on blade outlet width of centrifugal pumps is pointed out. In the case of different outlet widths, the flow field in six centrifugal pumps whose specific speed vary from 45 to 260 are simulated by using commercial code FLUENT and the characteristics are predicted. The standard k-ε turbulence model and SIMPLEC algorithm are chosen in FLUENT. The simulation is steady and moving reference frame is used to consider rotor-stator interaction. The research results show that the change of impeller outlet width has obvious impacts on characteristics at design point, flow field and the shape of performance curves. At nominal condition, the change of outlet width has more important effects on moderate specific speed centrifugal pumps. The flow field analysis indicates that blade outlet width change has an important effect on the location and area of low pressure region behind the blade inlet, jet-wake structure in impellers, the secondary flow in volute cross section and the back flow in impellers. The head-flow curve becomes more flat with the increase of outlet width. For moderate and low specific speed centrifugal pumps, the high efficiency area of efficiency-flow curve get bigger with the increase of outlet width and the area will be constant within certain outlet width change scope for high specific speed centrifugal pump. The research results agree well with experiment results.

Sign in / Sign up

Export Citation Format

Share Document