Artificial Microsystems for Sensing Airflow, Temperature, and Humidity by Combining MEMS and CMOS Technologies

2017 ◽  
pp. 243-256
Author(s):  
Nicolas André ◽  
Laurent A. Francis ◽  
Bertrand Rue ◽  
Denis Flandre ◽  
Jean-Pierre Raskin
Keyword(s):  
Temperature And Humidity

Cryo-TEM of amphiphilic polymer and amphiphile/polymer solutions

1993 ◽  
Vol 51 ◽  
pp. 876-877
Author(s):  
Yeshayahu Talmon
Keyword(s):  
Microstructural Characterization ◽  
Building Blocks ◽  
Quantitative Information ◽  
Physical Models ◽  
Specimen Preparation ◽  
Time Resolved ◽  
Temperature Changes ◽  
Temperature And Humidity ◽  
Microstructured Fluids ◽  
Air Streams

To achieve complete microstructural characterization of self-aggregating systems, one needs direct images in addition to quantitative information from non-imaging, e.g., scattering or Theological measurements, techniques. Cryo-TEM enables us to image fluid microstructures at better than one nanometer resolution, with minimal specimen preparation artifacts. Direct images are used to determine the “building blocks” of the fluid microstructure; these are used to build reliable physical models with which quantitative information from techniques such as small-angle x-ray or neutron scattering can be analyzed.To prepare vitrified specimens of microstructured fluids, we have developed the Controlled Environment Vitrification System (CEVS), that enables us to prepare samples under controlled temperature and humidity conditions, thus minimizing microstructural rearrangement due to volatile evaporation or temperature changes. The CEVS may be used to trigger on-the-grid processes to induce formation of new phases, or to study intermediate, transient structures during change of phase (“time-resolved cryo-TEM”). Recently we have developed a new CEVS, where temperature and humidity are controlled by continuous flow of a mixture of humidified and dry air streams.

Strretlight pole metal as the medium of Tetragonula sp nest in Indralaya, South Sumatra

2019 ◽  
Vol 1 (2) ◽  
Author(s):  
Hanifa Marisa
Keyword(s):  
Zea Mays ◽  
Air Temperature ◽  
Hevea Brasiliensis ◽  
Citrullus Lanatus ◽  
Ground Surface ◽  
Temperature And Humidity ◽  
Surface Diameter ◽  
Very High

An investigation had been done to Tetragonula (Tetragona) sp nest at Indralaya, South Sumatra to describe the Tetragonula sp nest that use streetlight pole as nest medium during April - May 2019. Purpossive sampling is used to select the target nest. Two streetlight pole found be used by Tetragonula sp as their home. The coordinate of location, heght from ground surface, diameter of streetlight pole, air temperature and humidity, and floral species around nest, were noted. Spot coordinate are S 30 14’ 19.2498’’ and E 1040 39’ 15,3288’’ ; 1,5 m above the ground surface, 12 cm diameter pole, highest air temperature was 35 o C at daylight (April and May 2019), 80 – 90 % humidity at April-May 2019; which Switenia macrophyla, Hevea brasiliensis, Zea mays, and Citrullus lanatus floral species are planted around. Air temperature in the pole is very high, around 40 0 C during daylight.

Temperature and Humidity Dependent Reliability Analysis of RGB LED Chips

2006 ◽  
Author(s):  
Jun-Xian Fu ◽  
Shukri Souri ◽  
James S. Harris
Keyword(s):  
Reliability Analysis ◽  
Printed Circuit Board ◽  
Light Emitting Diode ◽  
Circuit Board ◽  
Light Emitting ◽  
Printed Circuit ◽  
Root Cause ◽  
Micro Cracks ◽  
Temperature And Humidity

Abstract Temperature and humidity dependent reliability analysis was performed based on a case study involving an indicator printed-circuit board with surface-mounted multiple-die red, green and blue light-emitting diode chips. Reported intermittent failures were investigated and the root cause was attributed to a non-optimized reflow process that resulted in micro-cracks and delaminations within the molding resin of the chips.

Sign in / Sign up

Export Citation Format

Share Document