Fatigue strength of truss girders made of Very High Strength Steel

2010 ◽  
pp. 499-505 ◽  
Author(s):  
R Pijpers ◽  
M Kolstein
Keyword(s):  
Fatigue Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Very High

The prediction for fatigue strength in very high cycle regime of high strength steel

2016 ◽  
Vol 9 (3) ◽  
pp. 197-209 ◽  
Author(s):  
Ming Zhang ◽  
Weiqiang Wang ◽  
Pengfei Wang ◽  
Yan Liu ◽  
Jianfeng Li
Keyword(s):  
Fatigue Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Very High

DOCOL 100W

Alloy Digest ◽  
2003 ◽  
Vol 52 (7) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
High Strength Steel ◽  
High Strength ◽  
Bend Strength ◽  
Very High

Abstract Docol 100W is a very-high-strength steel that is used for transportation products. This datasheet provides information on composition, physical properties, tensile properties, and bend strength. It also includes information on joining. Filing Code: SA-516. Producer or source: SSAB Swedish Steel Inc.

DOMEX 110XF

Alloy Digest ◽  
2003 ◽  
Vol 52 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Strength Steel ◽  
Civil Engineering ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
Structural Components ◽  
Very High

Abstract Domex 110XF is a very-high-strength steel that is used for automotive and civil engineering structural components. This datasheet provides information on composition, physical properties, hardness, tensile properties, and bend strength as well as fracture toughness. It also includes information on heat treating and joining. Filing Code: SA-512. Producer or source: SSAB Swedish Steel Inc.

Increasing the fatigue strength of high-strength steel parts by repeated treatment with shot peening

2020 ◽  
pp. 79-82
Author(s):  
G.N. Kravchenko ◽  
K.G. Kravchenko
Keyword(s):  
Fatigue Strength ◽  
Shot Peening ◽  
High Strength Steel ◽  
High Strength ◽  
Resource Recovery ◽  
Repeated Treatment ◽  
Multiple Processing

The effectiveness of multiple hardening by shot peening of samples made of «30ХГСН2А» high-strength steel to increase their fatigue strength is experimentally established. Repeated hardenings allow not only to restore the original durability and even significantly increase it. Keywords fatigue strength, durability, resource recovery, multiple processing by shot peening, repeated hardening, high-strength steel. [email protected]

Capability of martensitic low transformation temperature welding consumables for increasing the fatigue strength of high strength steel joints

2020 ◽  
Vol 62 (9) ◽  
pp. 891-900
Author(s):  
Jonas Hensel ◽  
Arne Kromm ◽  
Thomas Nitschke-Pagel ◽  
Jonny Dixneit ◽  
Klaus Dilger
Keyword(s):  
Residual Stress ◽  
Phase Transformation ◽  
Fatigue Strength ◽  
High Strength Steel ◽  
Transformation Temperature ◽  
Fatigue Cracks ◽  
High Strength ◽  
Filler Material ◽  
Phase Transformation Temperature ◽  
Filler Materials

Abstract The use of low transformation temperature (LTT) filler materials represents a smart approach for increasing the fatigue strength of welded high strength steel structures apart from the usual procedures of post weld treatment. The main mechanism is based on the effect of the low start temperature of martensite formation on the stress already present during welding. Thus, compressive residual stress formed due to constrained volume expansion in connection with phase transformation become highly effective. Furthermore, the weld metal has a high hardness that can delay the formation of fatigue cracks but also leads to low toughness. Fundamental investigations on the weldability of an LTT filler material are presented in this work, including the characterization of the weld microstructure, its hardness, phase transformation temperature and mechanical properties. Special attention was applied to avoid imperfections in order to ensure a high weld quality for subsequent fatigue testing. Fatigue tests were conducted on the welded joints of the base materials S355J2 and S960QL using conventional filler materials as a comparison to the LTT filler. Butt joints were used with a variation in the weld type (DY-weld and V-weld). In addition, a component-like specimen (longitudinal stiffener) was investigated where the LTT filler material was applied as an additional layer. The joints were characterized with respect to residual stress, its stability during cyclic loading and microstructure. The results show that the application of LTT consumables leads to a significant increase in fatigue strength when basic design guidelines are followed. This enables a benefit from the lightweight design potential of high-strength steel grades.

TAP Project

2004 ◽  
Author(s):  
Carlo Maria Spinelli ◽  
Furio Marchersani
Keyword(s):  
High Pressure ◽  
High Strength Steel ◽  
High Strength ◽  
Innovation Activity ◽  
Long Distance ◽  
Gas Network ◽  
Research And Innovation ◽  
Gas Market ◽  
High Pressure Pipeline ◽  
Very High

International gas market development is towards very long transportation distances (3000–6000 km); the only suitable onshore technology to conjugate economics, large amount of gas conveyed and possibility to exploit remote gas fields appears to be the Very High Pressure (P > 14 MPa), Very High Strength Steel (Steel grade X100 API 5L [1] equivalent) option. Eni Group is going to sponsor a 3 years long project, called TAP (Trasporto gas Alta Pressione) [High Pressure gas Transportation] aimed to demonstrate: • economic evaluation; • technology reliability; • real possibility to build Very High Pressure Pipeline. The project itself is framed into five logical areas: • Evaluation of the applicability of alternative technological solution in extreme enterprise; • Technological innovation, mainly within Eni Group; • FEED (Front End Engineering Development) for strategic route gas pipeline and comparison with LNG option; • Demonstrative construction of a High Strength Steel (X80) pipeline section on Snam Rete Gas Network in Italy; • Demonstrative construction of a Very High Strength Steel (X100 API equivalent) provisioning pilot section pipeline. To achieve this object Eni has involved: • Eni Gas & Power Division as Business Developer; • Snamprogetti as Technology Developer; • Aquater, Enidata, Enitecnologie, Saipem, Snam Rete Gas as specific item expertises; • CSM and Universita` di Bergamo as high qualified partners for lab and full scale testing; • Pipe steel makers and coating producers as fundamental partners to develop new solutions. TAP, within Eni Group, is the final step of a long development research and innovation activity started 8 years ago with two explorative “Long distance pipeline High Grade Steel” projects on Very High Strength Steel performances (strength, toughness, weldability) carried out mainly with the support of Snam, Snamprogetti and Saipem. TAP final goal is to collect, transfer, develop all the possible technological solutions to be ready for building “The pipeline network for Very High Pressure Transportation”.

Sign in / Sign up

Export Citation Format

Share Document