Cost effective near surface 3D seismic imaging in heterogeneous subsurface using portable geophone array and a laptop

2001 ◽  
Author(s):  
Ran Bachrach ◽  
Tapan Mukerji
Keyword(s):  
Seismic Imaging ◽  
Cost Effective ◽  
3D Seismic ◽  
Near Surface

Fracture-Tolerant and Shear-Resistant Interlayers for Mitigation of Reflective Cracking

2019 ◽  
Vol 2673 (10) ◽  
pp. 35-46
Author(s):  
Cristian Cocconcelli ◽  
Bongsuk Park ◽  
Jian Zou ◽  
George Lopp ◽  
Reynaldo Roque
Keyword(s):  
Asphalt Pavement ◽  
Aggregate Size ◽  
Cost Effective ◽  
Design Guidelines ◽  
Reflective Cracking ◽  
Rubber Membrane ◽  
Near Surface ◽  
Field Evidence ◽  
Cracking Performance ◽  
Interface Cracking

Reflective cracking is frequently reported as the most common distress affecting resurfaced pavements. An asphalt rubber membrane interlayer (ARMI) approach has been traditionally used in Florida to mitigate reflective cracking. However, recent field evidence has raised doubts about the effectiveness of the ARMI when placed near the surface, indicating questionable benefits to reflective cracking and increased instability rutting potential. The main purpose of this research was to develop guidelines for an effective alternative to the ARMI for mitigation of near-surface reflective cracking in overlays on asphalt pavement. Fourteen interlayer mixtures, covering three aggregate types widely used in Florida, and two nominal maximum aggregate sizes (NMAS) were designed according to key characteristics identified for mitigation of reflective cracking, that is, sufficient gradation coarseness and high asphalt content. The dominant aggregate size range—interstitial component (DASR-IC) model was used for the design of all mixture gradations. A composite specimen interface cracking (CSIC) test was employed to evaluate reflective cracking performance of interlayer systems. In addition, asphalt pavement analyzer (APA) tests were performed to determine whether the interlayer mixtures had sufficient rutting resistance. The results indicated that interlayer mixtures designed with lower compaction effort, reduced design air voids, and coarser gradation led to more cost-effective fracture-tolerant and shear-resistant (FTSR) interlayers. Therefore, preliminary design guidelines including minimum effective film thickness and maximum DASR porosity requirements were proposed for 9.5-mm NMAS (35 µm and 50%) and 4.75-mm NMAS FTSR mixtures (20 µm and 60%) to mitigate near-surface reflective cracking.

scholarly journals Near-surface real-time seismic imaging using parsimonious interferometry

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sherif M. Hanafy ◽  
Hussein Hoteit ◽  
Jing Li ◽  
Gerard T. Schuster
Keyword(s):  
Fluid Flow ◽  
Real Time ◽  
Temporal Resolution ◽  
Seismic Imaging ◽  
Time Lapse ◽  
Rock Properties ◽  
Recording Time ◽  
Near Surface ◽  
Arrival Times ◽  
Order Of Magnitude

AbstractResults are presented for real-time seismic imaging of subsurface fluid flow by parsimonious refraction and surface-wave interferometry. Each subsurface velocity image inverted from time-lapse seismic data only requires several minutes of recording time, which is less than the time-scale of the fluid-induced changes in the rock properties. In this sense this is real-time imaging. The images are P-velocity tomograms inverted from the first-arrival times and the S-velocity tomograms inverted from dispersion curves. Compared to conventional seismic imaging, parsimonious interferometry reduces the recording time and increases the temporal resolution of time-lapse seismic images by more than an order-of-magnitude. In our seismic experiment, we recorded 90 sparse data sets over 4.5 h while injecting 12-tons of water into a sand dune. Results show that the percolation of water is mostly along layered boundaries down to a depth of a few meters, which is consistent with our 3D computational fluid flow simulations and laboratory experiments. The significance of parsimonious interferometry is that it provides more than an order-of-magnitude increase of temporal resolution in time-lapse seismic imaging. We believe that real-time seismic imaging will have important applications for non-destructive characterization in environmental, biomedical, and subsurface imaging.

Free gas distribution and basal shear zone development in a subaqueous landslide – Insight from 3D seismic imaging of the Tuaheni Landslide Complex, New Zealand

2018 ◽  
Vol 502 ◽  
pp. 231-243 ◽  
Author(s):  
Felix Gross ◽  
Joshu J. Mountjoy ◽  
Gareth J. Crutchley ◽  
Christoph Böttner ◽  
Stephanie Koch ◽  
...  
Keyword(s):  
New Zealand ◽  
Shear Zone ◽  
Seismic Imaging ◽  
3D Seismic ◽  
Gas Distribution ◽  
Free Gas ◽  
Zone Development ◽  
Basal Shear
Sign in / Sign up

Export Citation Format

Share Document