Experimental determination of the elastic coefficients of an orthorhombic material

Geophysics ◽  
2001 ◽  
Vol 66 (4) ◽  
pp. 1217-1225 ◽  
Author(s):  
M. Mah ◽  
D. R. Schmitt

In terms of elastic anisotropy, many rocks may be considered to have orthorhombic symmetry. Experimentally determining the nine independent elastic coefficients required for this case remains challenging. Elastic coefficients are most often found from measurements of the phase velocity in a variety of directions throughout a material, but finding this plane‐wave velocity is problematic. Here, quasi‐P and quasi‐S phase speeds are found using the τ‐p transformation through a composite material of orthorhombic symmetry. Arrays of specially constructed transducers (0.65 MHz) with different modes of vibration were placed on a rectangular prism of the material. More than 620 individual measures of phase speed were obtained at different directions and subsequently used in a generalized least‐squares inversion that yields the required elastic coefficients. The analysis does not account for the effects of wave‐speed dispersion evident in the waveforms acquired in the composite material. This dispersion is particularly severe for the in‐plane, quasi‐S polarization and is possibly a consequence of the fine layered structure of the material.

2002 ◽  
Vol 408-412 ◽  
pp. 1389-1394 ◽  
Author(s):  
G. Langelaan ◽  
Sophie Ryelandt ◽  
Francis Delannay ◽  
J.H. Root ◽  
Paul van Houtte
Keyword(s):  

2020 ◽  
Vol 17 (35) ◽  
pp. 599-608 ◽  
Author(s):  
Alexander A. OREKHOV ◽  
Yuri A. UTKIN ◽  
Polina F. PRONINA

One of the significant innovative technologies is the creation of large-sized structures that work for a long time in space and meet stringent restrictions on overall mass characteristics. Among these structures, in the first place, is the section of bearing truss (BT). This article presents the results of experimental studies of sectors of load-bearing trusses of mesh design for compression. Recently, composite mesh cylindrical shells are used as spacecraft housings. The mesh shell is a supporting structure to which the instruments and mechanisms of the spacecraft are attached. The truss section is made of cross-linked polymer composite material with carbon fibers. The objective of the tests is to confirm the possibility of creating a lightweight mesh construction using a carbon fiber reinforced polymer composite material. To achieve this goal, the authors were assigned the following tasks: selection of carbon filler of polymer composite materials (PCM); selection of PCM binder; determination of the degree of carbon fiber reinforcement; choice of the number and orientation paths of spiral ribs, number of ring ribs and the sizes of individual ribs. As a result of the research, the calculated indicators for ensuring the bearing capacity and stiffness under the application of axial compressive load were obtained. At the same time, with the determination of bearing capacity, the deformation characteristics of the structure were twice determined in order to confirm their repeatability, as well as linear nature of the dependence of axial and radial deformations as a result of the applied load.


1957 ◽  
Vol 24 (4) ◽  
pp. 594-601
Author(s):  
M. A. Biot ◽  
D. G. Willis

Abstract The theory of the deformation of a porous elastic solid containing a compressible fluid has been established by Biot. In this paper, methods of measurement are described for the determination of the elastic coefficients of the theory. The physical interpretation of the coefficients in various alternate forms is also discussed. Any combination of measurements which is sufficient to fix the properties of the system may be used to determine the coefficients. For an isotropic system, in which there are four coefficients, the four measurements of shear modulus, jacketed and unjacketed compressibility, and coefficient of fluid content, together with a measurement of porosity appear to be the most convenient. The porosity is not required if the variables and coefficients are expressed in the proper way. The coefficient of fluid content is a measure of the volume of fluid entering the pores of a solid sample during an unjacketed compressibility test. The stress-strain relations may be expressed in terms of the stresses and strains produced during the various measurements, to give four expressions relating the measured coefficients to the original coefficients of the consolidation theory. The same method is easily extended to cases of anisotropy. The theory is directly applicable to linear systems but also may be applied to incremental variations in nonlinear systems provided the stresses are defined properly.


2018 ◽  
Vol 60 ◽  
pp. 00027 ◽  
Author(s):  
Andrii Sudakov ◽  
Andrii Dreus ◽  
Diana Sudakova ◽  
Oleksandr Khamininch

The article presents the results of experimental and theoretical studies, the purpose of which was to substantiate the technology of drilling wells isolation using new thermoplastic composite material. The basis of the proposed material is gravel, and secondary polyethylene terephthalate acts as a binding material. The use of the proposed insulation material avoids a number of disadvantages specific for traditional grouting mortars. The technology of material application provides its melting in a well by thermomechanical drilling. The article deals with the issues, related to the substantiation of the optimal formulation of a thermoplastic composite material based on secondary polyethylene terephthalate, and the determination of rational operating parameters of thermomechanical drilling, which allow to melt effectively the material at the bottom of a well. The possibility of material application for the insulation of absorbing horizons in borehole conditions has been proved. Based on the analysis of the heat balance at the bottom of a well, the calculation procedure has been proposed and the dependences of the velocity and time of thermomechanical melting of the grouting thermoplastic composite material on the operating parameters of drilling, thermal properties and geometric characteristics of the drill bit, have been determined.


2015 ◽  
Vol 70 (4) ◽  
pp. 92-96
Author(s):  
S. V. Sheshenin ◽  
P. V. Chistyakov ◽  
V. V. Galatenko ◽  
D. I. Kalugin ◽  
O. N. Shornikova ◽  
...  

2018 ◽  
Vol 244 ◽  
pp. 01026 ◽  
Author(s):  
Ondrej Stalmach ◽  
Vladimir Dekys ◽  
Frantisek Barnik ◽  
Jan Simon

This paper deals with measurement of emissivity of the composite samples. Three composite samples with the different thickness are heated to the temperature sixty-five degrees Celsius. On each sample must be applied a known emissivity coating. Unknown emissivity is calculated using the information obtained during the measurement. The aim of this paper is to show one of the possible approaches to find out the emissivity of the composite material.


Sign in / Sign up

Export Citation Format

Share Document