Three‐dimensional seismic monitoring of an enhanced oil recovery process

Geophysics ◽  
1987 ◽  
Vol 52 (9) ◽  
pp. 1175-1187 ◽  
Author(s):  
Robert J. Greaves ◽  
Terrance J. Fulp
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Three Dimensional ◽  
Recovery Process ◽  
Bright Spot ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Common Depth Point

Seismic reflection data were used to monitor the progress of an in‐situ combustion, enhanced oil recovery process. Three sets of three‐dimensional (3-D) data were collected during a one‐year period in order to map the extent and directions of propagation in time. Acquisition and processing parameters were identical for each survey so that direct one‐to‐one comparison of traces could be made. Seismic attributes were calculated for each common‐depth‐point data set, and in a unique application of seismic reflection data, the preburn attributes were subtracted from the midburn and postburn attributes. The resulting “difference volumes” of 3-D seismic data showed anomalies which were the basis for the interpretation shown in this case study. Profiles and horizon slices from the data sets clearly show the initiation and development of a bright spot in the reflection from the top of the reservoir and a dim spot in the reflection from a limestone below it. Interpretation of these anomalies is supported by information from postburn coring. The bright spot was caused by increased gas saturation along the top‐of‐reservoir boundary. From postburn core data, a map of burn volume distribution was made. In comparison, the bright spot covered a greater area, and it was concluded that combustion and injection gases had propagated ahead of the actual combustion zone. The dim spot anomaly shows good correlation with the burn volume in distribution and direction. Evidence from postburn logs supports the conclusion that the burn substantially decreased seismic velocity and increased seismic attenuation in the reservoir. Net burn thicknesses measured in the cores were used to calibrate the dim‐spot amplitude. With this calibration, the dim‐spot amplitude at each common depth point was inverted to net burn thickness and a map of estimated burn thickness was made from the seismic data.

High‐resolution seismic study in the Gas Hills uranium district, Wyoming

Geophysics ◽  
1982 ◽  
Vol 47 (10) ◽  
pp. 1355-1374
Author(s):  
James K. Applegate ◽  
David A. Emilia ◽  
Edwin B. Neitzel ◽  
Paul R. Donaldson
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Three Dimensional ◽  
Synthetic Seismograms ◽  
Seismic Reflection Data ◽  
Structural Controls ◽  
Reflection Data ◽  
Passive Seismic ◽  
Channel Deposits

A study was undertaken to evaluate the effectiveness of the high‐resolution seismic technique for the mapping of stratigraphic and structural controls in the Gas Hills uranium district, Wyoming. The test area is one in which uranium deposits are in Tertiary sediments which unconformably overlie a Mesozoic Paleozoic section. Paleochannels on the unconformity appear to control the localization of the uranium. Drilling in the area allows an evaluation of the effectiveness of the study. Using both sonic and density logs, we computed synthetic seismograms to evaluate the feasibility of predicting the success of the seismic reflection technique and to test this prediction using surface seismic methods. The field study was undertaken utilizing primarily two energy sources—a high‐frequency vibrator (40–350 Hz), and one‐pound dynamite charges shot in 10-ft holes. A limited amount of data was also acquired using detonating cord on the surface. Some three‐dimensional (3-D) data were also acquired, and a later study acquired passive seismic data. The seismic reflection data were successful not only in delineating the unconformable surface and in mapping paleodrainages on the unconformity, but also in defining channel deposits within the Tertiary section. Correlation with the logs shows the success of the study. Several areas were delineated where one would undertake tight drilling patterns, and other areas were delineated in which one might minimize or eliminate exploratory drilling. The synthetic seismograms also could have predicted the success of the seismic work.

scholarly journals Improved Interpretation of Deep Seismic Reflection Data in Areas of Complex Geology Through Integration With Passive Seismic Data Sets

2018 ◽  
Vol 123 (12) ◽  
pp. 10,810-10,830
Author(s):  
Michael Dentith ◽  
Huaiyu Yuan ◽  
Ruth Elaine Murdie ◽  
Perla Pina-Varas ◽  
Simon P. Johnson ◽  
...  
Keyword(s):  
Seismic Data ◽  
Seismic Reflection ◽  
Data Sets ◽  
Seismic Reflection Data ◽  
Deep Seismic Reflection ◽  
Reflection Data ◽  
Passive Seismic ◽  
Complex Geology

Late Cretaceous – Cenozoic history of the transition zone between the East European Craton and the Paleozoic Platform, Polish sector of the Baltic Sea, revealed by new offshore regional seismic reflection data (BALTEC project)

2021 ◽  
Author(s):  
Piotr Krzywiec ◽  
Łukasz Słonka ◽  
Quang Nguyen ◽  
Michał Malinowski ◽  
Mateusz Kufrasa ◽  
...  
Keyword(s):  
High Resolution ◽  
Late Cretaceous ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Upper Cretaceous ◽  
Seismic Reflection Data ◽  
East European ◽  
Reflection Data ◽  
Multichannel Seismic Reflection ◽  
Multichannel Seismic Reflection Data

<p>In 2016, approximately 850 km of high-resolution multichannel seismic reflection data of the BALTEC survey have been acquired offshore Poland within the transition zone between the East European Craton and the Paleozoic Platform. Data processing, focused on removal of multiples, strongly overprinting geological information at shallower intervals, included SRME, TAU-P domain deconvolution, high resolution parabolic Radon demultiple and SWDM (Shallow Water De-Multiple). Entire dataset was Kirchhoff pre-stack time migrated. Additionally, legacy shallow high-resolution multichannel seismic reflection data acquired in this zone in 1997 was also used. All this data provided new information on various aspects of the Phanerozoic evolution of this area, including Late Cretaceous to Cenozoic tectonics and sedimentation. This phase of geological evolution could be until now hardly resolved by analysis of industry seismic data as, due to limited shallow seismic imaging and very strong overprint of multiples, essentially no information could have been retrieved from this data for first 200-300 m. Western part of the BALTEC dataset is located above the offshore segment of the Mid-Polish Swell (MPS) – large anticlinorium formed due to inversion of the axial part of the Polish Basin. BALTEC seismic data proved that Late Cretaceous inversion of the Koszalin – Chojnice fault zone located along the NE border of the MPS was thick-skinned in nature and was associated with substantial syn-inversion sedimentation. Subtle thickness variations and progressive unconformities imaged by BALTEC seismic data within the Upper Cretaceous succession in vicinity of the Kamień-Adler and the Trzebiatów fault zones located within the MPS documented complex interplay of Late Cretaceous basin inversion, erosion and re-deposition. Precambrian basement of the Eastern, cratonic part of the study area is overlain by Cambro-Silurian sedimentary cover. It is dissected by a system of steep, mostly reverse faults rooted in most cases in the deep basement. This fault system has been regarded so far as having been formed mostly in Paleozoic times, due to the Caledonian orogeny. As a consequence, Upper Cretaceous succession, locally present in this area, has been vaguely defined as a post-tectonic cover, locally onlapping uplifted Paleozoic blocks. New seismic data, because of its reliable imaging of the shallowest substratum, confirmed that at least some of these deeply-rooted faults were active as a reverse faults in latest Cretaceous – earliest Paleogene. Consequently, it can be unequivocally proved that large offshore blocks of Silurian and older rocks presently located directly beneath the Cenozoic veneer must have been at least partly covered by the Upper Cretaceous succession; then, they were uplifted during the widespread inversion that affected most of Europe. Ensuing regional erosion might have at least partly provided sediments that formed Upper Cretaceous progradational wedges recently imaged within the onshore Baltic Basin by high-end PolandSPAN regional seismic data. New seismic data imaged also Paleogene and younger post-inversion cover. All these results prove that Late Cretaceous tectonics substantially affected large areas located much farther towards the East than previously assumed.</p><p>This study was funded by the Polish National Science Centre (NCN) grant no UMO-2017/27/B/ST10/02316.</p>

Crustal structure and surface zonation of the Canadian Appalachians: implications of deep seismic reflection data

1989 ◽  
Vol 26 (2) ◽  
pp. 305-321 ◽  
Author(s):  
François Marillier ◽  
Charlotte E. Keen ◽  
Glen S. Stockmal ◽  
Garry Quinlan ◽  
Harold Williams ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Three Dimensional ◽  
Surface Expression ◽  
Seismic Profiles ◽  
Crust And Upper Mantle ◽  
Seismic Reflection Data ◽  
Central Block ◽  
Reflection Data ◽  
Lower Crustal ◽  
Canadian Appalachians

In 1986, 1181 km of marine seismic reflection data was collected to 18–20 s of two-way traveltime in the Gulf of St. Lawrence area. The seismic profiles sample all major surface tectono-stratigraphic zones of the Canadian Appalachians. They complement the 1984 deep reflection survey northeast of Newfoundland. Together, the seismic profiles reveal the regional three-dimensional geometry of the orogen.Three lower crustal blocks are distinguished on the seismic data. They are referred to as the Grenville, Central, and Avalon blocks, from west to east. The Grenville block is wedge shaped in section, and its subsurface edge follows the form of the Appalachian structural front. The Grenville block abuts the Central block at mid-crustal to mantle depths. The Avalon block meets the Central block at a steep junction that penetrates the entire crust.Consistent differences in the seismic character of the Moho help identify boundaries of the deep crustal blocks. The Moho signature varies from uniform over extended distances to irregular with abrupt depth changes. In places the Moho is offset by steep reflections that cut the lower crust and upper mantle. In other places, the change in Moho elevation is gradual, with lower crustal reflections following its form. In all three blocks the crust is generally highly reflective, with no distinction between a transparent upper crust and reflective lower crust.In general, Carboniferous and Mesozoic basins crossed by the seismic profiles overlie thinner crust. However, a deep Moho is found at some places beneath the Carboniferous Magdalen Basin.The Grenville block belongs to the Grenville Craton; the Humber Zone is thrust over its dipping southwestern edge. The Dunnage Zone is allochthonous above the opposing Grenville and Central blocks. The Gander Zone may be the surface expression of the Central block or may be allochthonous itself. There is a spatial analogy between the Avalon block and the Avalon Zone. Our profile across the Meguma Zone is too short to seismically distinguish this zone from the Avalon Zone.

scholarly journals Monte Carlo reservoir analysis combining seismic reflection data and informed priors

Geophysics ◽  
2015 ◽  
Vol 80 (1) ◽  
pp. R31-R41 ◽  
Author(s):  
Andrea Zunino ◽  
Klaus Mosegaard ◽  
Katrine Lange ◽  
Yulia Melnikova ◽  
Thomas Mejer Hansen
Keyword(s):  
Monte Carlo ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Probabilistic Approach ◽  
Multiple Point ◽  
Petroleum Reservoir ◽  
Inversion Algorithm ◽  
Reservoir Properties ◽  
Seismic Reflection Data ◽  
Reflection Data

Determination of a petroleum reservoir structure and rock bulk properties relies extensively on inference from reflection seismology. However, classic deterministic methods to invert seismic data for reservoir properties suffer from some limitations, among which are the difficulty of handling complex, possibly nonlinear forward models, and the lack of robust uncertainty estimations. To overcome these limitations, we studied a methodology to invert seismic reflection data in the framework of the probabilistic approach to inverse problems, using a Markov chain Monte Carlo (McMC) algorithm with the goal to directly infer the rock facies and porosity of a target reservoir zone. We thus combined a rock-physics model with seismic data in a single inversion algorithm. For large data sets, the McMC method may become computationally impractical, so we relied on multiple-point-based a priori information to quantify geologically plausible models. We tested this methodology on a synthetic reservoir model. The solution of the inverse problem was then represented by a collection of facies and porosity reservoir models, which were samples of the posterior distribution. The final product included probability maps of the reservoir properties in obtained by performing statistical analysis on the collection of solutions.

scholarly journals Entrainment and abrasion of megaclasts during submarine landsliding and their impact on flow behaviour

2018 ◽  
Vol 477 (1) ◽  
pp. 223-240 ◽  
Author(s):  
D. M. Hodgson ◽  
H. L. Brooks ◽  
A. Ortiz-Karpf ◽  
Y. Spychala ◽  
D. R. Lee ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Three Dimensional ◽  
Submarine Landslides ◽  
Seismic Reflection Data ◽  
Karoo Basin ◽  
Reflection Data ◽  
Seabed Topography ◽  
Flow Evolution ◽  
Basal Shear ◽  
Process Product

AbstractMany mass transport complexes (MTCs) contain up to kilometre-scale (mega)clasts encased in a debritic matrix. Although many megaclasts are sourced from the headwall areas, the irregular basal shear surfaces of many MTCs indicate that megaclast entrainment during the passage of flows into the deeper basin is also common. However, the mechanisms responsible for the entrainment of large blocks of substrate, and their influence on the longitudinal behaviour of the associated flows, have not been widely considered. We present examples of megaclasts from exhumed MTCs (the Neuquén Basin, Argentina and the Karoo Basin, South Africa) and MTCs imaged in three-dimensional seismic reflection data (Magdalena Fan, offshore Colombia and Santos Basin, offshore Brazil) to investigate these process–product interactions. We show that highly sheared basal surfaces are well developed in distal locations, sometimes extending beyond their associated deposit. This points to deformation and weakening of the substrate ahead of the flow, suggesting that preconditioning of the substrate by distributed shear ahead of, and to the side of, a mass flow could result in the entrainment of large fragments. An improved understanding of the interactions between flow evolution, seabed topography, and the entrainment and abrasion of megaclasts will help to refine estimates of run-out distances, and therefore the geohazard potential of submarine landslides.

Instantaneous spectral bandwidth and dominant frequency with applications to seismic reflection data

Geophysics ◽  
1993 ◽  
Vol 58 (3) ◽  
pp. 419-428 ◽  
Author(s):  
Arthur E. Barnes
Keyword(s):  
Instantaneous Frequency ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Power Spectra ◽  
Dominant Frequency ◽  
Center Frequency ◽  
Spectral Bandwidth ◽  
Instantaneous Amplitude ◽  
Seismic Reflection Data ◽  
Reflection Data

Fourier power spectra are often usefully characterized by average measures. In reflection seismology, the important average measures are center frequency, spectral bandwidth, and dominant frequency. These quantities have definitions familiar from probability theory: center frequency is the spectral mean, spectral bandwidth is the standard deviation about that mean, and dominant frequency is the square root of the second moment, which serves as an estimate of the zero‐crossing frequency. These measures suggest counterparts defined with instantaneous power spectra in place of Fourier power spectra, so that they are instantaneous in time though they represent averages in frequency. Intuitively reasonable requirements yield specific forms for these instantaneous quantities that can be computed with familiar complex seismic trace attributes. Instantaneous center frequency is just instantaneous frequency. Instantaneous bandwidth is the absolute value of the derivative of the instantaneous amplitude divided by the instantaneous amplitude. Instantaneous dominant frequency is the square root of the sum of the squares of the instantaneous frequency and instantaneous bandwidth. Instantaneous bandwidth and dominant frequency find employment as additional complex seismic trace attributes in the detailed study of seismic data. Instantaneous bandwidth is observed to be nearly always less than instantaneous frequency; the points where it is larger may mark the onset of distinct wavelets. These attributes, together with instantaneous frequency, are perhaps, of greater use in revealing the time‐varying spectral properties of seismic data. They can help in the search for low frequency shadows or in the analysis of frequency change due to effects of data processing. Instantaneous bandwidth and dominant frequency complement instantaneous frequency and should find wide application in the analysis of seismic reflection data.

scholarly journals Structural Interpretation of Yamama and Naokelekan Formations in Tuba Oil Field Using 2D Seismic Data

2021 ◽  
Vol 54 (2B) ◽  
pp. 55-64
Author(s):  
Belal M. Odeh
Keyword(s):  
Seismic Data ◽  
Seismic Reflection ◽  
Synthetic Seismogram ◽  
Oil Field ◽  
Well Log ◽  
Seismic Reflection Data ◽  
Depth Maps ◽  
Reflection Data ◽  
Interpretation Process ◽  
Southern Iraq

This research includes structure interpretation of the Yamama Formation (Lower Cretaceous) and the Naokelekan Formation (Jurassic) using 2D seismic reflection data of the Tuba oil field region, Basrah, southern Iraq. The two reflectors (Yamama and Naokelekan) were defined and picked as peak and tough depending on the 2D seismic reflection interpretation process, based on the synthetic seismogram and well log data. In order to obtain structural settings, these horizons were followed over all the regions. Two-way travel-time maps, depth maps, and velocity maps have been produced for top Yamama and top Naokelekan formations. The study concluded that certain longitudinal enclosures reflect anticlines in the east and west of the study area representing Zubair and Rumaila fold confined between them a fold consist of two domes represents Tuba fold with the same trending of Zubair and Rumaila structures. The study confirmed the importance of this field as a reservoir of the accumulation of hydrocarbons.

scholarly journals Reassessing legacy seismic reflection data. Extracting new information through advanced seismic processing schemes.

2021 ◽  
Author(s):  
Ramon Carbonell ◽  
Yesenia Martinez ◽  
Irene de Felipe ◽  
Juan Alcalde ◽  
Imma Palomeras ◽  
...  
Keyword(s):  
Land Use Planning ◽  
Seismic Data ◽  
Seismic Reflection ◽  
Leading Edge ◽  
Critical Issue ◽  
Commercial Development ◽  
Natural Risk ◽  
Seismic Reflection Data ◽  
Seismic Processing ◽  
Reflection Data

<p><span>Hardware and software innovations taking place since the commercial development of seismic reflection imaging in the 60’s and early 70’s have resulted in various improved powerful seismic imaging solutions. Overall, these have been very successful in contrasting geological environments pursuing a wide variety of different targets. The innovative advances in seismic processing may constitute critical tools when analyzing seismic data acquired in highly heterogeneous geologic environments as they can efficiently increase the resolution power. In addition, they can become relevant when using modern acquisition instrumentation and strategies. Furthermore, these new developments significantly increase the value of legacy seismic reflection data. Currently, reassessing controlled source seismic data is becoming a critical issue mostly due to the increasing difficulties for acquiring new profiles posed by environmental regulations and high prices. However, the knowledge of the subsurface is an asset for our society, for example: </span><span><span>land-use planning and management; natural risk assessments; or exploration and exploitation for geo-resources. Here we present examples of analysis schemes such as seismic attribute analysis and Common Reflection Surface stacking applied on a number of old seismic reflection profiles (Deep lithospheric transects as well as high resolution profiles) in an effort to bring up their validity. Results indicate how these leading edge methods contribute to significantly improve the quality of vintage seismic data, significantly reducing reflector uncertainties and easing their interpretation. </span></span></p><p><span><span>This research is supported by: Generalitat de Catalunya (AGAUR) grant 2017SGR1022 (GREG); EU (H2020) 871121 (EPOS-SP); EIT-RaewMaterias 17024 (SIT4ME). </span></span></p><p> </p>

The Sask Craton and Hearne Province margin: seismic reflection studies in the western Trans-Hudson Orogen

2005 ◽  
Vol 42 (4) ◽  
pp. 403-419 ◽  
Author(s):  
Z Hajnal ◽  
J Lewry ◽  
D White ◽  
K Ashton ◽  
R Clowes ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Three Dimensional ◽  
Three Dimensional Model ◽  
Seismic Reflection Data ◽  
Reflection Data ◽  
Regional Tectonic ◽  
Detachment Zone ◽  
Tectonic Development ◽  
Seismic Images ◽  
Basal Detachment

A three-dimensional model of the regional crustal architecture of the western Trans-Hudson Orogen, based on the interpretation of 590 km of deep-sounding seismic reflection data and a comparable length of existing seismic reflection information, is presented. The seismic images identify the regional geometry of the basal detachment zone (Pelican thrust) that separates juvenile allochthonous terranes from the underlying Archean microcontinent (Sask craton). The Sask Craton is inferred to have a minimum spatial extent of over 100 000 km2 with an associated crustal root that extends for 200 km along strike. During terminal collision, complete convergence of the Rae–Hearne and Superior continental blocks was precluded by the presence of the Sask Craton, resulting in the preservation of anomalous amounts of oceanic and associated sedimentary juvenile material. Along regional tectonic strike, consistency of crustal structure across the Rae–Hearne margin – Reindeer zone boundary is established. Several phases of tectonic development, including multistage subduction and continent–continent collision, are inferred for the western margin of the orogen. A bright, shallow (2–3.5 s two-way traveltime) band of reflectivity (Wollaston Lake reflector) imaged over ~150 000 km2 area is inferred to be a large post-orogenic mafic intrusion. A highly reflective, well-defined and structurally disturbed Moho discontinuity is mapped throughout the western Trans-Hudson Orogen. The present-day crustal architecture of the western Trans-Hudson Orogen is described in terms of the tectonic evolution within the region.

Sign in / Sign up

Export Citation Format

Share Document