A ray inversion method for refraction analysis

Geophysics ◽  
1985 ◽  
Vol 50 (11) ◽  
pp. 1701-1720 ◽  
Author(s):  
Glyn M. Jones ◽  
D. B. Jovanovich
Keyword(s):  
Field Data ◽  
Opposite Sign ◽  
Synthetic Data ◽  
Head Wave ◽  
Inversion Method ◽  
Data Set ◽  
Near Surface ◽  
Left And Right ◽  
A New Technique ◽  
Good Agreement

A new technique is presented for the inversion of head‐wave traveltimes to infer near‐surface structure. Traveltimes computed along intersecting pairs of refracted rays are used to reconstruct the shape of the first refracting horizon beneath the surface and variations in refractor velocity along this boundary. The information derived can be used as the basis for further processing, such as the calculation of near‐surface static delays. One advantage of the method is that the shape of the refractor is determined independently of the refractor velocity. With multifold coverage, rapid lateral changes in refractor geometry or velocity can be mapped. Two examples of the inversion technique are presented: one uses a synthetic data set; the other is drawn from field data shot over a deep graben filled with sediment. The results obtained using the synthetic data validate the method and support the conclusions of an error analysis, in which errors in the refractor velocity determined using receivers to the left and right of the shots are of opposite sign. The true refractor velocity therefore falls between the two sets of estimates. The refraction image obtained by inversion of the set of field data is in good agreement with a constant‐velocity reflection stack and illustrates that the ray inversion method can handle large lateral changes in refractor velocity or relief.

scholarly journals Imaging near-surface heterogeneities by natural migration of backscattered surface waves: Field data test

Geophysics ◽  
2017 ◽  
Vol 82 (3) ◽  
pp. S197-S205 ◽  
Author(s):  
Zhaolun Liu ◽  
Abdullah AlTheyab ◽  
Sherif M. Hanafy ◽  
Gerard Schuster
Keyword(s):  
Surface Waves ◽  
Field Data ◽  
Synthetic Data ◽  
Data Sets ◽  
Data Set ◽  
Near Surface ◽  
3D Data ◽  
Strong Surface ◽  
Migration Method ◽  
Recorded Data

We have developed a methodology for detecting the presence of near-surface heterogeneities by naturally migrating backscattered surface waves in controlled-source data. The near-surface heterogeneities must be located within a depth of approximately one-third the dominant wavelength [Formula: see text] of the strong surface-wave arrivals. This natural migration method does not require knowledge of the near-surface phase-velocity distribution because it uses the recorded data to approximate the Green’s functions for migration. Prior to migration, the backscattered data are separated from the original records, and the band-passed filtered data are migrated to give an estimate of the migration image at a depth of approximately one-third [Formula: see text]. Each band-passed data set gives a migration image at a different depth. Results with synthetic data and field data recorded over known faults validate the effectiveness of this method. Migrating the surface waves in recorded 2D and 3D data sets accurately reveals the locations of known faults. The limitation of this method is that it requires a dense array of receivers with a geophone interval less than approximately one-half [Formula: see text].

Regularization and datuming of seismic data by weighted, damped least squares

Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. U67-U76 ◽  
Author(s):  
Robert J. Ferguson
Keyword(s):  
Least Squares ◽  
Seismic Data ◽  
Synthetic Data ◽  
Real Data ◽  
Structural Data ◽  
Irregular Sampling ◽  
Data Set ◽  
Near Surface ◽  
Damped Least Squares ◽  
Wavefield Extrapolation

The possibility of improving regularization/datuming of seismic data is investigated by treating wavefield extrapolation as an inversion problem. Weighted, damped least squares is then used to produce the regularized/datumed wavefield. Regularization/datuming is extremely costly because of computing the Hessian, so an efficient approximation is introduced. Approximation is achieved by computing a limited number of diagonals in the operators involved. Real and synthetic data examples demonstrate the utility of this approach. For synthetic data, regularization/datuming is demonstrated for large extrapolation distances using a highly irregular recording array. Without approximation, regularization/datuming returns a regularized wavefield with reduced operator artifacts when compared to a nonregularizing method such as generalized phase shift plus interpolation (PSPI). Approximate regularization/datuming returns a regularized wavefield for approximately two orders of magnitude less in cost; but it is dip limited, though in a controllable way, compared to the full method. The Foothills structural data set, a freely available data set from the Rocky Mountains of Canada, demonstrates application to real data. The data have highly irregular sampling along the shot coordinate, and they suffer from significant near-surface effects. Approximate regularization/datuming returns common receiver data that are superior in appearance compared to conventional datuming.

scholarly journals MAX-DOAS observations of aerosols, formaldehyde and nitrogen dioxide in the Beijing area: comparison of two profile retrieval approaches

2015 ◽  
Vol 8 (2) ◽  
pp. 941-963 ◽  
Author(s):  
T. Vlemmix ◽  
F. Hendrick ◽  
G. Pinardi ◽  
I. De Smedt ◽  
C. Fayt ◽  
...  
Keyword(s):  
Standard Deviation ◽  
A Priori ◽  
Systematic Bias ◽  
Aerosol Extinction ◽  
Data Set ◽  
Near Surface ◽  
Beijing Area ◽  
Least Squares Fit ◽  
Relative Differences ◽  
Good Agreement

Abstract. A 4-year data set of MAX-DOAS observations in the Beijing area (2008–2012) is analysed with a focus on NO2, HCHO and aerosols. Two very different retrieval methods are applied. Method A describes the tropospheric profile with 13 layers and makes use of the optimal estimation method. Method B uses 2–4 parameters to describe the tropospheric profile and an inversion based on a least-squares fit. For each constituent (NO2, HCHO and aerosols) the retrieval outcomes are compared in terms of tropospheric column densities, surface concentrations and "characteristic profile heights" (i.e. the height below which 75% of the vertically integrated tropospheric column density resides). We find best agreement between the two methods for tropospheric NO2 column densities, with a standard deviation of relative differences below 10%, a correlation of 0.99 and a linear regression with a slope of 1.03. For tropospheric HCHO column densities we find a similar slope, but also a systematic bias of almost 10% which is likely related to differences in profile height. Aerosol optical depths (AODs) retrieved with method B are 20% high compared to method A. They are more in agreement with AERONET measurements, which are on average only 5% lower, however with considerable relative differences (standard deviation ~ 25%). With respect to near-surface volume mixing ratios and aerosol extinction we find considerably larger relative differences: 10 ± 30, −23 ± 28 and −8 ± 33% for aerosols, HCHO and NO2 respectively. The frequency distributions of these near-surface concentrations show however a quite good agreement, and this indicates that near-surface concentrations derived from MAX-DOAS are certainly useful in a climatological sense. A major difference between the two methods is the dynamic range of retrieved characteristic profile heights which is larger for method B than for method A. This effect is most pronounced for HCHO, where retrieved profile shapes with method A are very close to the a priori, and moderate for NO2 and aerosol extinction which on average show quite good agreement for characteristic profile heights below 1.5 km. One of the main advantages of method A is the stability, even under suboptimal conditions (e.g. in the presence of clouds). Method B is generally more unstable and this explains probably a substantial part of the quite large relative differences between the two methods. However, despite a relatively low precision for individual profile retrievals it appears as if seasonally averaged profile heights retrieved with method B are less biased towards a priori assumptions than those retrieved with method A. This gives confidence in the result obtained with method B, namely that aerosol extinction profiles tend on average to be higher than NO2 profiles in spring and summer, whereas they seem on average to be of the same height in winter, a result which is especially relevant in relation to the validation of satellite retrievals.

scholarly journals Coupled hydrogeophysical parameter estimation using a sequential Bayesian approach

2010 ◽  
Vol 14 (3) ◽  
pp. 545-556 ◽  
Author(s):  
J. Rings ◽  
J. A. Huisman ◽  
H. Vereecken
Keyword(s):  
Water Content ◽  
Particle Filtering ◽  
Field Data ◽  
Synthetic Data ◽  
Time Domain Reflectometry ◽  
Second Step ◽  
Parameter Estimates ◽  
Posterior Distributions ◽  
Data Set ◽  
Resistivity Tomography

Abstract. Coupled hydrogeophysical methods infer hydrological and petrophysical parameters directly from geophysical measurements. Widespread methods do not explicitly recognize uncertainty in parameter estimates. Therefore, we apply a sequential Bayesian framework that provides updates of state, parameters and their uncertainty whenever measurements become available. We have coupled a hydrological and an electrical resistivity tomography (ERT) forward code in a particle filtering framework. First, we analyze a synthetic data set of lysimeter infiltration monitored with ERT. In a second step, we apply the approach to field data measured during an infiltration event on a full-scale dike model. For the synthetic data, the water content distribution and the hydraulic conductivity are accurately estimated after a few time steps. For the field data, hydraulic parameters are successfully estimated from water content measurements made with spatial time domain reflectometry and ERT, and the development of their posterior distributions is shown.

Near-surface scattering phenomena and implications for tunnel detection

2015 ◽  
Vol 3 (1) ◽  
pp. SF43-SF54 ◽  
Author(s):  
Shelby L. Peterie ◽  
Richard D. Miller
Keyword(s):  
Synthetic Data ◽  
P Wave ◽  
S Wave ◽  
Seismic Line ◽  
Data Set ◽  
Near Surface ◽  
Tunnel Detection ◽  
Impedance Contrast ◽  
Diffraction Imaging ◽  
Imaging Algorithms

Tunnel locations are accurately interpreted from diffraction sections of focused mode converted P- to S-wave diffractions from a perpendicular tunnel and P-wave diffractions from a nonperpendicular (oblique) tunnel. Near-surface tunnels are ideal candidates for diffraction imaging due to their small size relative to the seismic wavelength and large acoustic impedance contrast at the tunnel interface. Diffraction imaging algorithms generally assume that the velocities of the primary wave and the diffracted wave are approximately equal, and that the diffraction apex is recorded directly above the scatterpoint. Scattering phenomena from shallow tunnels with kinematic properties that violate these assumptions were observed in one field data set and one synthetic data set. We developed the traveltime equations for mode-converted and oblique diffractions and demonstrated a diffraction imaging algorithm designed for the roll-along style of acquisition. Potential processing and interpretation pitfalls specific to these diffraction types were identified. Based on our observations, recommendations were made to recognize and image mode-converted and oblique diffractions and accurately interpret tunnel depth, horizontal location, and azimuth with respect to the seismic line.

Warping least-squares inversion for 4D velocity change: Gulf of Mexico case study

2019 ◽  
Vol 7 (2) ◽  
pp. SB23-SB31
Author(s):  
Chang Li ◽  
Mark Meadows ◽  
Todd Dygert
Keyword(s):  
Gulf Of Mexico ◽  
Least Squares ◽  
Synthetic Data ◽  
Inversion Method ◽  
Velocity Change ◽  
Data Set ◽  
Phase Constraints ◽  
Free Case ◽  
Velocity Changes

We have developed a new trace-based, warping least-squares inversion method to quantify 4D velocity changes. There are two steps to solve for these velocity changes: (1) dynamic warping with phase constraints to align the baseline and monitor traces and (2) least-squares inversion for 4D velocity changes incorporating the time shifts and 4D amplitude differences (computed after trace alignment by warping). We have demonstrated this new inversion workflow using simple synthetic layered models. For the noise-free case, phase-constrained warping is superior to standard, amplitude-based warping by improving trace alignment, resulting in more accurate inverted velocity changes (less than 1% error). For synthetic data with 6% rms noise, inverted velocity changes are reasonably accurate (less than 10% error). Additional inversion tests with migrated finite-difference data shot over a realistic anticline model result in less than 10% error. The inverted velocity changes on a 4D field data set from the Gulf of Mexico are more interpretable and consistent with the dynamic reservoir model than those estimated from the conventional time-strain method.

3D plane-wave migration in tilted coordinates: A field data example

Geophysics ◽  
2009 ◽  
Vol 74 (6) ◽  
pp. WCA199-WCA209 ◽  
Author(s):  
Guojian Shan ◽  
Robert Clapp ◽  
Biondo Biondi
Keyword(s):  
Plane Wave ◽  
Field Data ◽  
Synthetic Data ◽  
Data Set ◽  
Wave Source ◽  
Surface Data ◽  
The One ◽  
Wave Migration ◽  
Wavefield Extrapolation ◽  
Slant Stacking

We have extended isotropic plane-wave migration in tilted coordinates to 3D anisotropic media and applied it on a Gulf of Mexico data set. Recorded surface data are transformed to plane-wave data by slant-stack processing in inline and crossline directions. The source plane wave and its corresponding slant-stacked data are extrapolated into the subsurface within a tilted coordinate system whose direction depends on the propagation direction of the plane wave. Images are generated by crosscorrelating these two wavefields. The shot sampling is sparse in the crossline direction, and the source generated by slant stacking is not really a plane-wave source but a phase-encoded source. We have discovered that phase-encoded source migration in tilted coordinates can image steep reflectors, using 2D synthetic data set examples. The field data example shows that 3D plane-wave migration in tilted coordinates can image steeply dipping salt flanks and faults, even though the one-way wave-equation operator is used for wavefield extrapolation.

Inversion of ground constant offset loop-loop electromagnetic data for a large range of induction numbers

Geophysics ◽  
2015 ◽  
Vol 80 (1) ◽  
pp. E11-E21 ◽  
Author(s):  
Julien Guillemoteau ◽  
Pascal Sailhac ◽  
Charles Boulanger ◽  
Jérémie Trules
Keyword(s):  
Synthetic Data ◽  
Test Site ◽  
Maxwell Theory ◽  
Data Set ◽  
Electromagnetic Data ◽  
Apparent Conductivity ◽  
Airborne Electromagnetic ◽  
Phase Data ◽  
Ground Conductivity ◽  
Good Agreement

Ground loop-loop electromagnetic surveys are often conducted to fulfill the low-induction-number condition. To image the distribution of electric conductivity inside the ground, it is then necessary to collect a multioffset data set. We considered that less time-consuming constant offset measurements can also reach this objective. This can be achieved by performing multifrequency soundings, which are commonly performed for the airborne electromagnetic method. Ground multifrequency soundings have to be interpreted carefully because they contain high-induction-number data. These data are interpreted in two steps. First, the in-phase and out-of-phase data are converted into robust apparent conductivities valid for all the induction numbers. Second, the apparent conductivity data are inverted in 1D and 2D to obtain the true distribution of the ground conductivity. For the inversion, we used a general half-space Jacobian for the apparent conductivity valid for all the induction numbers. This method was applied and validated on synthetic data computed with the full Maxwell theory. The method was then applied on field data acquired in the test site of Provins, in the Parisian basin, France. The result revealed good agreement with borehole and geologic information, demonstrating the applicability of our method.

A periodically varying code for improving deblending of simultaneous sources in marine acquisition

Geophysics ◽  
2016 ◽  
Vol 81 (3) ◽  
pp. V213-V225 ◽  
Author(s):  
Shaohuan Zu ◽  
Hui Zhou ◽  
Yangkang Chen ◽  
Shan Qu ◽  
Xiaofeng Zou ◽  
...  
Keyword(s):  
Field Data ◽  
Synthetic Data ◽  
Data Sets ◽  
Ocean Bottom ◽  
Data Set ◽  
Acceptable Model ◽  
Model Subspace ◽  
New Form ◽  
Simultaneous Source ◽  
Practical Field

We have designed a periodically varying code that can avoid the problem of the local coherency and make the interference distribute uniformly in a given range; hence, it was better at suppressing incoherent interference (blending noise) and preserving coherent useful signals compared with a random dithering code. We have also devised a new form of the iterative method to remove interference generated from the simultaneous source acquisition. In each iteration, we have estimated the interference using the blending operator following the proposed formula and then subtracted the interference from the pseudodeblended data. To further eliminate the incoherent interference and constrain the inversion, the data were then transformed to an auxiliary sparse domain for applying a thresholding operator. During the iterations, the threshold was decreased from the largest value to zero following an exponential function. The exponentially decreasing threshold aimed to gradually pass the deblended data to a more acceptable model subspace. Two numerically blended synthetic data sets and one numerically blended practical field data set from an ocean bottom cable were used to demonstrate the usefulness of our proposed method and the better performance of the periodically varying code over the traditional random dithering code.

First-arrival traveltime tomography based on the adjoint-state method

Geophysics ◽  
2009 ◽  
Vol 74 (6) ◽  
pp. WCB1-WCB10 ◽  
Author(s):  
Cédric Taillandier ◽  
Mark Noble ◽  
Hervé Chauris ◽  
Henri Calandra
Keyword(s):  
Synthetic Data ◽  
Point Of View ◽  
Data Set ◽  
Near Surface ◽  
Traveltime Tomography ◽  
Adjoint State ◽  
Gradient Based ◽  
First Arrival ◽  
State Method ◽  
Adjoint State Method

Classical algorithms used for traveltime tomography are not necessarily well suited for handling very large seismic data sets or for taking advantage of current supercomputers. The classical approach of first-arrival traveltime tomography was revisited with the proposal of a simple gradient-based approach that avoids ray tracing and estimation of the Fréchet derivative matrix. The key point becomes the derivation of the gradient of the misfit function obtained by the adjoint-state technique. The adjoint-state method is very attractive from a numerical point of view because the associated cost is equivalent to the solution of the forward-modeling problem, whatever the size of the input data and the number of unknown velocity parameters. An application on a 2D synthetic data set demonstrated the ability of the algorithm to image near-surface velocities with strong vertical and lateral variations and revealed the potential of the method.

Sign in / Sign up

Export Citation Format

Share Document