Removal of Cu2+ and Ni2+ ions from aqueous solutions by adsorption onto natural palygorskite and vermiculite

Clay Minerals ◽  
2018 ◽  
Vol 53 (1) ◽  
pp. 1-15 ◽  
Author(s):  
A. Bourliva ◽  
A. K. Sikalidis ◽  
L. Papadopoulou ◽  
M. Betsiou ◽  
K. Michailidis ◽  
...  
Keyword(s):  
Clay Minerals ◽  
Pore Diameter ◽  
Low Cost ◽  
Natural Clay ◽  
X Ray ◽  
Batch Type ◽  
Bet Specific Surface Area ◽  
Adsorption Processes ◽  
Pseudo Second Order ◽  
Isotherm Equations

ABSTRACTThe efficiency of two low-cost, abundant and natural clay minerals, palygorskite and vermiculite, in terms of reducing the concentation of Cu2+ and Ni2+ ions was evaluated here. Natural clay minerals were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), BET specific surface area and pore-diameter analysis. Batch-type experiments were performed and various parameters, i.e. pH, clay amount, contact time and initial metal concentration, that affect adsorption processes were investigated. The adsorption of Cu2+ and Ni2+ ions is pH-dependent, while minor clay quantities were sufficient to achieve high removal efficiencies. Adsorption equilibrium occurred in 60 min and the adsorption kinetics were better described by pseudo-second-order kinetics. Experimental results were analysed by the Langmuir, Freundlich, Dubinin–Radushkevich (D–R), Temkin and Halsey isotherm equations. The release of exchangeable cations (i.e. Ca2+, Mg2+, Na+ and K+) was examined to verify an ion-exchange mechanism.

scholarly journals Adsorption of Hexavalent Chromium Using Banana Pseudostem Biochar and Its Mechanism

2018 ◽  
Vol 10 (11) ◽  
pp. 4250 ◽  
Author(s):  
Shuang Xu ◽  
Weiguang Yu ◽  
Sen Liu ◽  
Congying Xu ◽  
Jihui Li ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Pyrolysis Temperature ◽  
Low Cost ◽  
Surface Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Adsorption Processes ◽  
Different Temperatures ◽  
Pseudo Second Order ◽  
Porosity Analysis

A low-cost biochar was prepared through slow pyrolysis of banana pseudostem biowaste at different temperatures, and characterized by surface area and porosity analysis, scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). It was shown that the biochar prepared at low pyrolysis temperature was rich in oxygen-containing groups on the surface. Adsorption experiments revealed that the biochar prepared at 300 °C (BB300) was the best adsorbent for Cr(VI) with 125.44 mg/g maximum adsorption capacity at pH 2 and 25 °C. All the adsorption processes were well described by pseudo-second-order and Langmuir models, indicating a monolayer chemiadsorption. Furthermore, it was demonstrated that adsorption of Cr(VI) was mainly attributed to reduction of Cr(VI) to Cr(III) followed by ion exchange and complexation with the biochar.

scholarly journals Equilibrium and Kinetic Study of Anionic and Cationic Pollutants Remediation by Limestone–Chitosan–Alginate Nanocomposite from Aqueous Solution

Molecules ◽  
2021 ◽  
Vol 26 (9) ◽  
pp. 2586
Author(s):  
Inas A. Ahmed ◽  
Ahmed H. Ragab ◽  
Mohamed A. Habila ◽  
Taghrid S. Alomar ◽  
Enas H. Aljuhani
Keyword(s):  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Entropy Change ◽  
Sem Images ◽  
Bet Analysis ◽  
Adsorption Processes ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Multilayer Formation

In this work, low-cost and readily available limestone was converted into nanolimestone chitosan and mixed with alginate powder and precipitate to form a triple nanocomposite, namely limestone—chitosan–alginate (NLS/Cs/Alg.), which was used as an adsorbent for the removal of brilliant green (BG) and Congo red (CR) dyes in aqueous solutions. The adsorption studies were conducted under varying parameters, including contact time, temperature, concentration, and pH. The NLS/Cs/Alg. was characterized by SEM, FTIR, BET, and TEM techniques. The SEM images revealed that the NLS/Cs/Alg. surface structure had interconnected pores, which could easily trap the pollutants. The BET analysis established the surface area to be 20.45 m2/g. The recorded maximum experimental adsorption capacities were 2250 and 2020 mg/g for CR and BG, respectively. The adsorption processes had a good fit to the kinetic pseudo second order, which suggests that the removal mechanism was controlled by physical adsorption. The CR and BG equilibrium data had a good fit for the Freundlich isotherm, suggesting that adsorption processes occurred on the heterogeneous surface with a multilayer formation on the NLS/Cs/Alg. at equilibrium. The enthalpy change (ΔH0) was 37.7 KJ mol−1 for CR and 8.71 KJ mol−1 for BG, while the entropy change (ΔS0) was 89.1 J K−1 mol−1 for CR and 79.1 J K−1 mol−1 BG, indicating that the adsorption process was endothermic and spontaneous in nature.

scholarly journals Synthesis Fe3O4/Talc nanocomposite by coprecipition-ultrasonication method and advances in hexavalent chromium removal from aqueous solution

2020 ◽  
Vol 38 (9-10) ◽  
pp. 483-501
Author(s):  
Nguyen Thi Huong ◽  
Nguyen Ngoc Son ◽  
Vo Hoang Phuong ◽  
Cong Tien Dung ◽  
Pham Thi Mai Huong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Batch Experiments ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The Fe3O4/Talc nanocomposite was synthesized by the coprecipitation-ultrasonication method. The reaction was carried out under a inert gas environment. The nanoparticles were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), fourier-transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry techniques (VSM), the surface area of the nanoparticles was determined to be 77.92 m2/g by Brunauer-Emmett-Teller method (BET). The kinetic data showed that the adsorption process fitted with the pseudo-second order model. Batch experiments were carried out to determine the adsorption kinetics and mechanisms of Cr(VI) by Fe3O4/Talc nanocomposite. The adsorption process was found to be highly pH-dependent, which made the material selectively adsorb these metals from aqueous solution. The isotherms of adsorption were also studied using Langmuir and Freundlich equations in linear forms. It is found that the Langmuir equation showed better linear correlation with the experimental data than the Freundlich. The thermodynamics of Cr(VI) adsorption onto the Fe3O4/Talc nanocomposite indicated that the adsorption was exothermic. The reusability study has proven that Fe3O4/Talc nanocomposite can be employed as a low-cost and easy to separate.

scholarly journals Characterization and Evaluation of Zeolite A/Fe3O4 Nanocomposite as a Potential Adsorbent for Removal of Organic Molecules from Wastewater

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Emmanuel Nyankson ◽  
Jonas Adjasoo ◽  
Johnson Kwame Efavi ◽  
Reuben Amedalor ◽  
Abu Yaya ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Isotherm Models ◽  
Adsorption Efficiency ◽  
Ferrous Chloride ◽  
X Ray ◽  
Intraparticle Diffusion Model ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Chloride Salts

In this work, zeolite (Z) and Z-Fe3O4 nanocomposite (Z-Fe3O4 NC) have been synthesized. The Fe3O4 nanoparticles were synthesized using the extract from maize leaves and ferric and ferrous chloride salts and encapsulated into the zeolite framework. The nanocomposite (Z-Fe3O4 NC) was characterized using X-ray diffractometer (XRD), Fourier-transform infrared (FT-IR) spectroscopy, energy-dispersive X-ray (EDX) spectroscopy, and scanning electron microscopy (SEM). The potential of Z-Fe3O4 NC as an adsorbent for removing methylene blue molecules (MB) from solution was examined using UV-Vis and kinetic and equilibrium isotherm models. The adsorption data fitted best with the pseudo-second-order model and Weber and Morris model, indicating that the adsorption process was chemisorption, while the Weber and Morris described the rate-controlling steps. The intraparticle diffusion model suggests that the adsorption processes were pore and surface diffusion controlled. The Langmuir isotherm model best describes the adsorption process indicating homogeneous monolayer coverage of MB molecules onto the surface of the Z-Fe3O4 NC. The maximum Langmuir adsorption capacity was 2.57 mg/g at 25°C. The maximum adsorption efficiency was 97.5%. After regeneration, the maximum adsorption efficiency achieved at a pH of 7 was 82.6%.

scholarly journals Biosorption of aniline blue from aqueous solution using a novel biosorbent Zizyphus oenoplia seeds: Modeling studies

2015 ◽  
Vol 17 (3) ◽  
pp. 70-77 ◽  
Author(s):  
M. Kumar ◽  
G. Elangovan ◽  
R. Tamilarasan ◽  
G. Vijayakumar ◽  
P.C. Mukeshkumar ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Sorption Process ◽  
Aniline Blue ◽  
Blue Dye ◽  
Batch Mode ◽  
Before And After ◽  
Intra Particle Diffusion ◽  
Pseudo Second Order ◽  
Isotherm Equations

Abstract This article presents the feasibility for the removal of Aniline Blue dye (AB dye) from aqueous solution using a low cost biosorbent material Zizyphus oenoplia seeds. In this study, a batch mode experiments of the adsorption process were carried out as a function of pH, contact time, concentration of dye, adsorbent dosage and temperature. The experimental data were fitted with Freundlich and Langmuir isotherm equations. The feasibility of the isotherm was evaluated with dimensionless separation factor (RL). The kinetic data of sorption process are evaluated by using pseudo-first order and pseudo-second order equations. The mode of diffusion process was evaluated with intra-particle diffusion model. The thermodynamic parameters like change in enthalpy (ΔHº); change in entropy (ΔSº) and Gibbs free energy change (ΔGº) were calculated using Van’t Hoff plot. The biosorbent material was characterized with Fourier Transform Infrared (FTIR) spectroscopy and the morphology was identified with Scanning Electron Microscope (SEM) in before and after adsorption of AB dye.

scholarly journals Development of low-cost iron mixed porous pellet adsorbent by mixture design approach and its application for arsenate and arsenite adsorption from water

2017 ◽  
Vol 36 (1-2) ◽  
pp. 372-392 ◽  
Author(s):  
Borano Te ◽  
Boonchai Wichitsathian ◽  
Chatpet Yossapol ◽  
Watcharapol Wonglertarak
Keyword(s):  
Low Cost ◽  
Mixture Design ◽  
Alkaline Condition ◽  
P Value ◽  
Maximum Adsorption Capacity ◽  
Natural Clay ◽  
Optimum Proportion ◽  
Negative Effect ◽  
Pseudo Second Order ◽  
Arsenite Removal

In this study, natural clay, iron oxide, and iron powder were combined to develop low-cost iron mixed porous pellet adsorbent for arsenate and arsenite removal from aqueous solution in batch experiments. The augmented simplex centroid mixture design was applied to obtain the optimum proportion of each constituent. Higher correlation coefficient of the models (R2 > 0.95), good distribution of residuals, and lower values of p value (<0.05) indicated that the method is suitable for determining the optimum mixture proportion. Extensive decrease of both arsenate and arsenite adsorption occurred in the alkaline condition (pH > 9). Kinetic and isotherm experimental data of both arsenate and arsenite were well described by the pseudo-second order and Sips models, respectively. The maximum adsorption capacity of arsenate and arsenite derived from Sips model were 13.33 and 19.06 mg/g, respectively. The separation and heterogeneity factors showed that both arsenate and arsenite were favorably adsorbed. Among coexisting anions, phosphate significantly showed negative effect on the adsorption of either arsenate or arsenite. The adsorbent could be effectively reused for several times after its regeneration and was considered as non-hazardous material after adsorption.

scholarly journals Kinetic and Thermodynamic Study of Adsorption of Copper (II) Ion on Moroccan Clay

2019 ◽  
Vol 9 (2) ◽  
pp. 102-115
Author(s):  
Hanane Essebaai ◽  
Ilham Ismi ◽  
Ahmed Lebkiri ◽  
Said Marzak ◽  
El Housseine Rifi
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
X Ray Diffraction ◽  
X Ray ◽  
Increase With Increase ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Kinetic And Thermodynamic Study

Highly efficient low-cost adsorbent was applied for copper (II) ions uptake from aqueous solution. Characteristics of natural adsorbent were established using scanning X-ray diffraction (XRD), X-ray fluorescence, electron microscope (SEM) and Fourier Transform Infra-Red (FTIR). Various physicochemical parameters such as contact time, initial copper(II) ions concentration, adsorbent dosage, pH of copper (II) ions solution and temperature were investigated. The result showed that the adsorption of copper (II) ions by natural clay was favorable at pH=5,5. The adsorption was found to increase with increase in initial copper (II) ions concentration, and contact time. Equilibrium adsorption data were fitted using three isotherms and kinetic data tested with four kinetic models. Freundlich isotherm best described the adsorption of copper (II) ions onto utilised clay, the maximum monolayer adsorption capacity (qmax) was 8 mg/g. Pseudo-second-order model best described the kinetics of the adsorption process. Thermodynamic parameters such as Gibbs free energy, enthalpy and entropy were determined. It was found that copper (II) ions adsorption was spontaneous (ΔG°<0) and endothermic (ΔH°>0).

scholarly journals Granules of brick waste (GBW) as low-cost sorbent for removal of Pb+2 ions from aqueous solutions

2020 ◽  
Vol 27 (3) ◽  
pp. 1-8
Author(s):  
Teba H. Mhawesh ◽  
Ziad T. Abd Ali
Keyword(s):  
Aqueous Solutions ◽  
Low Cost ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Sorption Data ◽  
X Ray ◽  
Batch Tests ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The potential application of granules of Granular brick waste as a low-cost sorbent for removal of Pb+2 ions from aqueous solutions has been studied. The properties of Granular brick waste were determined through several tests such as X-Ray diffraction , Energy dispersive X-ray, Scanning electron microscopy , and surface area. In batch tests, the influence of several operating parameters including contact time, initial concentration, agitation speed, and the dose of GBW was investigated. The best values of these parameters that provided maximum removal efficiency of lead (89.5 %) were 2.5 hr, 50 mg/L, 250 rpm, and 1.8 g/100mL, respectively. The sorption data obtained by batch experiments subjected to the three isotherm models called Langmuir, Freundlich and   Elovich. The results showed that the Langmuir isotherm model described well the sorption data (R2= 0.9866) in comparison with other models. The kinetic data were analyzed using two kinetic models called pseudo_first_order and pseudo_second_order. The pseudo-second-order kinetic model was found to agree well with the experimental data.

scholarly journals Removal of Pb(II) from aqueous solutions using Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles

2016 ◽  
Vol 6 (4) ◽  
pp. 562-573 ◽  
Author(s):  
Farshad Omidvar-Hosseini ◽  
Farid Moeinpour
Keyword(s):  
Magnetic Nanoparticles ◽  
Low Cost ◽  
Acacia Nilotica ◽  
Environmentally Benign ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Monolayer Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles were synthesized by a low-cost, simple, and environmentally benign procedure. The adsorbent was characterized by several methods including X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. Then, the potential of Acacia Nilotica seed shell ash supported Ni0.5Zn0.5Fe2O4 magnetic nanoparticles was investigated for adsorption of Pb(II). The effect of different parameters including contact time, pH, adsorbent dosage and initial Pb(II) concentration on the Pb(II) removal yield was studied. The experimental data were fitted well with the pseudo-second order kinetic model (R2 = 0.999). The adsorption isotherm was described well by the Langmuir isotherm (R2 = 0.900) with a maximum monolayer adsorption capacity of 37.6 mg g–1. The process for purifying water treatment presented here is easy using the magnetic nanoparticles. Therefore, this adsorbent was found to be useful and valuable for controlling water pollution due to Pb(II) ions.

scholarly journals Equilibrium and Kinetic Study of Removal Copper(II) from Aqueous Solution Using Chicken Eggshells: Low Cost Sorbent

Molekul ◽  
2021 ◽  
Vol 16 (1) ◽  
pp. 28
Author(s):  
Mohammad Jihad Madiabu ◽  
Joko Untung ◽  
Imas Solihat ◽  
Andi Muhammad Ichzan
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Sorption Process ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Adsorption Condition ◽  
Pseudo Second Order ◽  
Effect Of Copper

The research aims to investigate feasibility eggshells as potential adsorbent to remove copper(II) ions from aqueous solution. Eggshells powder was characterized using X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. Effect of copper(II) initial concentration, adsorbent dosage, and contact time have conducted. The optimum adsorption condition obtained when 0.7 g eggshells applied to 50 mg/L copper(II) solution for 50 minutes. The maximum percentage of copper(II) removal was exceeded more than 85%. Langmuir and Freundlich isotherm model were applied to describe the equilibrium adsorption. Copper(II) kinetics sorption process was fitted to pseudo-second order model with a rate constant equal to 0.516 g/mg.min. The results clearly exhibit that eggshells powder can be effectively used to remove copper(II) ions from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document