scholarly journals Effective diameters of protein A-gold and goat anti-rabbit-gold conjugates visualized by field emission scanning electron microscopy.

1992 ◽  
Vol 40 (6) ◽  
pp. 751-758 ◽  
Author(s):  
P Lea ◽  
D K Gross
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Field Emission ◽  
Gold Particle ◽  
Protein A ◽  
Gold Complexes ◽  
Gold Particles ◽  
Gold Particle Size ◽  
Scanning Electron

High-voltage (15-30 kV) field emission scanning electron microscopy (FESEM) was used to evaluate the effects of gold particle size and protein concentration on the formation of protein-gold complexes. Six colloidal gold sols were prepared, ranging in diameter from 7.6 to 39.8 nm. The minimal protecting amounts (m.p.a.) of protein A and goat anti-rabbit antibody (GAR) were experimentally determined. Gold particles were conjugated at the m.p.a., one half the m.p.a., and ten times the m.p.a. for both proteins, and protein-gold complexes prepared for FESEM. The smallest colloidal gold particles required the most protein per milliliter of gold suspension for stabilization. Transmission electron microscopy was found to be the preferred method for accurate sizing of gold particles, whereas FESEM of protein-gold complexes permitted visualization of a protein halo around a spherical gold core. Protein halo width varied significantly with changes in gold particle size. Measurements of protein halos indicated that conjugation with the m.p.a. of protein A resulted in the thickest protein layers for all gold sizes. GAR conjugation with the m.p.a. again produced the thickest protein layers. However, GAR halos were significantly smaller than those obtained with protein A conjugation. The proteins used showed similar adsorption patterns for the larger gold particles. For smaller gold particles, proteins may act differently, and these complexes should be further characterized by low-voltage FESEM.

scholarly journals Gold Particle Size Determination on Au/TiO2-CeO2 Catalysts by Means of Carbon Monoxide, Hydrogen Chemisorption and Transmission Electron Microscopy

2009 ◽  
Vol 5 ◽  
pp. 13-23 ◽  
Author(s):  
C. Guzmán ◽  
Gloria Del Angel ◽  
Ricardo Gómez ◽  
F. Galindo ◽  
R. Zanella ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Carbon Monoxide ◽  
Particle Size ◽  
Gold Particle ◽  
Precipitation Method ◽  
Hydrogen Chemisorption ◽  
Gold Particles ◽  
Transmission Electron ◽  
Gold Particle Size

Au/TiO2 and Au/TiO2-CeO2 catalysts were prepared by the sol-gel method and carbon monoxide, hydrogen chemisorption and TEM spectroscopy have been exploited to determine the size of gold particles. The gold nanoparticles (8.1 to 2.1 nm) were deposited by using the deposition-precipitation method. The XRD characterization shows the presence of anatase as the TiO2 crystalline phase; while by XPS spectroscopy, the presence of Au°, Au2O3, Ce3+ and Ce4+ species co-existing in the Au/TiO2-CeO2 catalysts is shown. The characterizations by TPD-CO as well as by TPD-H2 (temperature programmed desorption) showed that on catalysts containing cerium, the gold particle size can be determined with great accuracy by using these chemisorption methods. The gold particle size calculated from either the CO or H2 thermodesorption values is in good agreement with that obtained by High Resolution Transmission Electron Microscopy (HRTEM) and Scanning Transmission Electron Microscopy (STEM) analyses. It was proposed that the TPD-CO and/or TPD-H2 techniques could be helpful for the characterization of the gold particles by TEM; especially when the high contrast in the pictures of the supports containing CeO2 prevents the particle size from being determined.

A New Image Processing Technique for STEM

1974 ◽  
Vol 32 ◽  
pp. 432-433
Author(s):  
Yasushi Kokubo ◽  
Hirotami Koike ◽  
Teruo Someya
Keyword(s):  
Electron Microscopy ◽  
Image Processing ◽  
Scanning Electron Microscopy ◽  
Elastic Scattering ◽  
Field Emission ◽  
Processing Technique ◽  
Image Processing Technique ◽  
Energy Analyzer ◽  
Scanning Microscope ◽  
Scanning Electron

One of the advantages of scanning electron microscopy is the capability for processing the image contrast, i.e., the image processing technique. Crewe et al were the first to apply this technique to a field emission scanning microscope and show images of individual atoms. They obtained a contrast which depended exclusively on the atomic numbers of specimen elements (Zcontrast), by displaying the images treated with the intensity ratio of elastically scattered to inelastically scattered electrons. The elastic scattering electrons were extracted by a solid detector and inelastic scattering electrons by an energy analyzer. We noted, however, that there is a possibility of the same contrast being obtained only by using an annular-type solid detector consisting of multiple concentric detector elements.

Isolasi Dan Karakterisasi Bentonit Alam Menjadi Nanopartikel Monmorillonit

2018 ◽  
Vol 3 (1) ◽  
pp. 12 ◽  
Author(s):  
Zaimahwati Zaimahwati ◽  
Yuniati Yuniati ◽  
Ramzi Jalal ◽  
Syahman Zhafiri ◽  
Yuli Yetri
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Surface Morphology ◽  
Average Diameter ◽  
Particle Size Analyzer ◽  
Ft Ir ◽  
Scanning Electron ◽  
Sedimentation Processes

<p>Pada penelitian ini telah dilakukan isolasi dan karakterisasi bentonit alam menjadi nanopartikel montmorillonit. Bentonit alam yang digunakan diambil dari desa Blangdalam, Kecamatan Nisam Kabupaten Aceh Utara.  Proses isolasi meliputi proses pelarutan dengan aquades, ultrasonic dan proses sedimentasi. Untuk mengetahui karakterisasi montmorillonit dilakukan uji FT-IR, X-RD dan uji morfologi permukaan dengan Scanning Electron Microscopy (SEM). Partikel size analyzer untuk menganalisis dan menentukan ukuran nanopartikel dari isolasi bentonit alam. Dari hasil penelitian didapat ukuran nanopartikel montmorillonit hasil isolasi dari bentonit alam diperoleh berdiameter rata-rata 82,15 nm.</p><p><em>In this research we have isolated and characterized natural bentonite into montmorillonite nanoparticles. Natural bentonite used was taken from Blangdalam village, Nisam sub-district, North Aceh district. The isolation process includes dissolving process with aquades, ultrasonic and sedimentation processes.  The characterization of montmorillonite, FT-IR, X-RD and surface morphology test by Scanning Electron Microscopy (SEM). Particle size analyzer to analyze and determine the size of nanoparticles from natural bentonite insulation. From the research results obtained the size of montmorillonite nanoparticles isolated from natural bentonite obtained an average diameter of 82.15 nm.</em></p>

scholarly journals A Review on Enhancing the Antibacterial Activity of ZnO: Mechanisms and Microscopic Investigation

2020 ◽  
Vol 15 (1) ◽  
Author(s):  
Buzuayehu Abebe ◽  
Enyew Amare Zereffa ◽  
Aschalew Tadesse ◽  
H. C. Ananda Murthy
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Antibacterial Activity ◽  
Field Emission ◽  
Volume Ratio ◽  
Electronic Configuration ◽  
Microscopic Investigation ◽  
Electron Microscopic ◽  
Active Materials ◽  
Scanning Electron

Abstract Metal oxide nanomaterials are one of the preferences as antibacterial active materials. Due to its distinctive electronic configuration and suitable properties, ZnO is one of the novel antibacterial active materials. Nowadays, researchers are making a serious effort to improve the antibacterial activities of ZnO by forming a composite with the same/different bandgap semiconductor materials and doping of ions. Applying capping agents such as polymers and plant extract that control the morphology and size of the nanomaterials and optimizing different conditions also enhance the antibacterial activity. Forming a nanocomposite and doping reduces the electron/hole recombination, increases the surface area to volume ratio, and also improves the stability towards dissolution and corrosion. The release of antimicrobial ions, electrostatic interaction, reactive oxygen species (ROS) generations are the crucial antibacterial activity mechanism. This review also presents a detailed discussion of the antibacterial activity improvement of ZnO by forming a composite, doping, and optimizing different conditions. The morphological analysis using scanning electron microscopy, field emission-scanning electron microscopy, field-emission transmission electron microscopy, fluorescence microscopy, and confocal microscopy can confirm the antibacterial activity and also supports for developing a satisfactory mechanism. Graphical abstract Graphical abstract showing the metal oxides antibacterial mechanism and the fluorescence and scanning electron microscopic images.

Vergleich verschiedener Immun-Dekorationsmethoden für die Rasterelektronenmikroskopie am Beispiel eines Protein-Antigens auf der Oberfläche der Hefe Candida albicans/ A Comparison of Decoration Techniques for the Demonstration of Immunocomplexes by Scanning Electron Microscopy: Labeling of a Protein Antigen on the Surface of the Yeast Candida albicans

1985 ◽  
Vol 40 (7-8) ◽  
pp. 539-550 ◽  
Author(s):  
Margarete Borg
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Candida Albicans ◽  
Protein A ◽  
Peritoneal Macrophages ◽  
Polystyrene Latex ◽  
Target Antigen ◽  
Protein Antigens ◽  
Critical Point Drying ◽  
Scanning Electron

Abstract The labeling of immunocomplexes for scanning electron microscopy (SEM) is a fairly new technique, and the various procedures, that have been proposed, have not yet been compared. Such comparative evaluation was performed with Candida protease as a target antigen. This secretory enzyme of the opportunistic yeast Candida albicans can be localized on the surface of fungal blastopores and mycelia, both after growth in proteinaceous medium and upon infection of murine peritoneal macrophages. The presence of the protease antigen was confirmed by immunofluorescence and by immunoperoxidase-light microscopy. The decoration of protease - anti protease complexes for SEM was attempted with colloids derived from the immunoperoxidase reaction, by the immunogold technique, and by antibodies linked to beads of synthetic polymers (polystyrene, polymethacrylate, polyacrolein). In addition, inactivated Staphylococcus aureus was used, which binds to antibodies through its protein-A. The high resolution by SEM of surface structures was matched only by the colloid based decoration techniques. All conjugates with beads suffered from inconsistent binding, which did not correspond with the distribution of the surface antigen. The comparatively best result with beads was obtained with polystyrene (Latex). Colloid based techniques in addition allow for critical point drying, which cannot be applied to synthetic beads in the usual manner.

Microstructure Investigations of Streak Formation in 6063 Aluminum Extrusions by Optical Metallographic Techniques

2013 ◽  
Vol 19 (2) ◽  
pp. 276-284 ◽  
Author(s):  
George Vander Voort ◽  
Beatriz Suárez-Peña ◽  
Juan Asensio-Lozano
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Hot Extrusion ◽  
Magnesium Silicide ◽  
Precipitation Strengthening ◽  
Surface Appearance ◽  
Aluminum Extrusions ◽  
Extruded Products ◽  
Scanning Electron

AbstractThe present study investigates the effect of the solidification strategy for AA 6063 alloy on the surface appearance of anodized extrusions. The microstructure of the samples was analyzed using both light optical microscopy and scanning electron microscopy. Results show that if heavy segregation occurs from rapid solidification, coarse Mg2Si particles form, thus reducing the potential for precipitation strengthening by the finer β-Mg2Si developed in the solid state. Differentially-strained regions formed during hot extrusion induce differences in particle size for magnesium silicide (Mg2Si) precipitates. Anodizing generates surface roughness due to Mg2Si particle dissolution and AlFeSi decohesion, which is related to both particle size and deformation. During anodizing, an oxide layer forms on the surface of the extruded products, which can lead to streak formation, usually a subject of rejection due to unacceptable heterogeneous reflectivity.

Sign in / Sign up

Export Citation Format

Share Document