scholarly journals Large-Eddy-simulation prediction of indirect combustion noise in the entropy wave generator experiment

2017 ◽  
Vol 10 (2) ◽  
pp. 154-168 ◽  
Author(s):  
Stéphane Moreau ◽  
C Becerril ◽  
LYM Gicquel
Keyword(s):  
Pressure Fluctuations ◽  
Large Eddy Simulations ◽  
Combustion Noise ◽  
Analytical Models ◽  
Computational Domain ◽  
Mean Flow ◽  
Long Distance ◽  
Acoustic Reflection ◽  
Large Eddy ◽  
Wave Generator

Compact and non-compact analytical solutions of the subsonic operating point of the entropy wave generator experiment are compared with detailed numerical results obtained by large Eddy simulations. Two energy deposition methods are presented to account for the experimental ignition sequence and geometry: a single-block deposition as previously used and a delayed deposition that reproduces the experimental protocle closely. The unknown inlet acoustic reflection coefficient is assumed to be fully reflective to be more physically consistent with the actual experimental setup. The time delay between the activation of the heating modules must be considered to retrieve the temperature signal measured at the vibrometer and pressure signals at the microphones. Moreover, pressure signals extracted from the large Eddy simulations in the outlet duct using the delayed ignition model clearly reproduce the experimental signals better than the analytical models. An additional simulation with actual temperature fluctuations directly injected at the inlet of the computational domain clearly shows that the pressure fluctuations produced by the acceleration of the hot slug yields indirect noise almost entirely. Finally, the entropy spot is shown to be distorted when convecting through the turbulent flow in the entropy wave generator nozzle. Its amplitude decreases and its shape is dispersed, but hardly any dissipation occurs. The distortion appears to be negligible through the nozzle and become important only when convected over a long distance in the downstream duct. As the dominant frequencies of the entropy wave generator entropy forcing are very low, the effects of dispersion by the mean flow are however weak.

scholarly journals Computing combustion noise by combining large eddy simulations with analytical models for the propagation of waves through turbine blades

2013 ◽  
Vol 341 (1-2) ◽  
pp. 131-140 ◽  
Author(s):  
Ignacio Duran ◽  
Matthieu Leyko ◽  
Stéphane Moreau ◽  
Franck Nicoud ◽  
Thierry Poinsot
Keyword(s):  
Turbine Blades ◽  
Large Eddy Simulations ◽  
Combustion Noise ◽  
Analytical Models ◽  
Large Eddy ◽  
Propagation Of Waves

scholarly journals Turbomachinery Noise Predictions: Present and Future

Acoustics ◽  
2019 ◽  
Vol 1 (1) ◽  
pp. 92-116 ◽  
Author(s):  
Stéphane Moreau
Keyword(s):  
Hybrid Methods ◽  
Free Field ◽  
Broadband Noise ◽  
Large Eddy Simulations ◽  
Analytical Models ◽  
Flat Plates ◽  
Tonal Noise ◽  
Noise Sources ◽  
Large Eddy ◽  
Rans Simulations

In future Ultra-High By-Pass Ratio turboengines, the turbomachinery noise (fan and turbine stages mainly) is expected to increase significantly. A review of analytical models and numerical methods to yield both tonal and broadband contributions of such noise sources is presented. The former rely on hybrid methods coupling gust response over very thin flat plates of finite chord length, either isolated or in cascade, and acoustic analogies in free-field and in a duct. The latter yields tonal noise with unsteady Reynolds-Averaged Navier–Stokes (u-RANS) simulations, and broadband noise with Large Eddy Simulations (LES). The analytical models are shown to provide good and fast first sound estimates at pre-design stages, and to easily separate the different noise sources. The u-RANS simulations are now able to give accurate estimates of tonal noise of the most complex asymmetric, heterogeneous fan-Outlet Guiding Vane (OGV) configurations. Wall-modeled LES on rescaled stage configurations have now been achieved on all components: a low-pressure compressor stage, a transonic high-pressure turbine stage and a fan-OGV configuration with good overall sound power level predictions for the latter. In this case, hybrid Lattice–Boltzmann/very large-eddy simulations also appear to be an excellent alternative to yield both contributions accurately at once.

RANS and Large Eddy Simulation of Internal Combustion Engine Flows—A Comparative Study

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Xiaofeng Yang ◽  
Saurabh Gupta ◽  
Tang-Wei Kuo ◽  
Venkatesh Gopalakrishnan
Keyword(s):  
Large Eddy Simulation ◽  
High Speed ◽  
Combustion Engine ◽  
Flow Analysis ◽  
Partial Geometry ◽  
Computational Domain ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rans Simulations

A comparative cold flow analysis between Reynolds-averaged Navier–Stokes (RANS) and large eddy simulation (LES) cycle-averaged velocity and turbulence predictions is carried out for a single cylinder engine with a transparent combustion chamber (TCC) under motored conditions using high-speed particle image velocimetry (PIV) measurements as the reference data. Simulations are done using a commercial computationally fluid dynamics (CFD) code CONVERGE with the implementation of standard k-ε and RNG k-ε turbulent models for RANS and a one-equation eddy viscosity model for LES. The following aspects are analyzed in this study: The effects of computational domain geometry (with or without intake and exhaust plenums) on mean flow and turbulence predictions for both LES and RANS simulations. And comparison of LES versus RANS simulations in terms of their capability to predict mean flow and turbulence. Both RANS and LES full and partial geometry simulations are able to capture the overall mean flow trends qualitatively; but the intake jet structure, velocity magnitudes, turbulence magnitudes, and its distribution are more accurately predicted by LES full geometry simulations. The guideline therefore for CFD engineers is that RANS partial geometry simulations (computationally least expensive) with a RNG k-ε turbulent model and one cycle or more are good enough for capturing overall qualitative flow trends for the engineering applications. However, if one is interested in getting reasonably accurate estimates of velocity magnitudes, flow structures, turbulence magnitudes, and its distribution, they must resort to LES simulations. Furthermore, to get the most accurate turbulence distributions, one must consider running LES full geometry simulations.

Investigation on hydrodynamic forces leading to coarse particle entrainment using Large-Eddy Simulations

2021 ◽  
Author(s):  
Gaston Latessa ◽  
Angela Busse ◽  
Manousos Valyrakis
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Large Scale ◽  
Large Eddy Simulations ◽  
Flow Conditions ◽  
Mean Flow ◽  
Protection Measures ◽  
Practical Applications ◽  
Particle Entrainment ◽  
Large Eddy

<p>The prediction of particle motion in a fluid flow environment presents several challenges from the quantification of the forces exerted by the fluid onto the solids -normally with fluctuating behaviour due to turbulence- and the definition of the potential particle entrainment from these actions. An accurate description of these phenomena has many practical applications in local scour definition and to the design of protection measures.</p><p>In the present work, the actions of different flow conditions on sediment particles is investigated with the aim to translate these effects into particle entrainment identification through analytical solid dynamic equations.</p><p>Large Eddy Simulations (LES) are an increasingly practical tool that provide an accurate representation of both the mean flow field and the large-scale turbulent fluctuations. For the present case, the forces exerted by the flow are integrated over the surface of a stationary particle in the streamwise (drag) and vertical (lift) directions, together with the torques around the particle’s centre of mass. These forces are validated against experimental data under the same bed and flow conditions.</p><p>The forces are then compared against threshold values, obtained through theoretical equations of simple motions such as rolling without sliding. Thus, the frequency of entrainment is related to the different flow conditions in good agreement with results from experimental sediment entrainment research.</p><p>A thorough monitoring of the velocity flow field on several locations is carried out to determine the relationships between velocity time series at several locations around the particle and the forces acting on its surface. These results a relevant to determine ideal locations for flow investigation both in numerical and physical experiments.</p><p>Through numerical experiments, a large number of flow conditions were simulated obtaining a full set of actions over a fixed particle sitting on a smooth bed. These actions were translated into potential particle entrainment events and validated against experimental data. Future work will present the coupling of these LES models with Discrete Element Method (DEM) models to verify the entrainment phenomena entirely from a numerical perspective.</p>

scholarly journals Stability and Sensitivity Analysis of Hydrodynamic Instabilities in Industrial Swirled Injection Systems

2017 ◽  
Author(s):  
Thomas L. Kaiser ◽  
Thierry Poinsot ◽  
Kilian Oberleithner
Keyword(s):  
Stability Analysis ◽  
Linear Stability ◽  
Linear Stability Analysis ◽  
Vortex Core ◽  
Large Eddy Simulations ◽  
Mode Shapes ◽  
Mean Flow ◽  
Precessing Vortex Core ◽  
Large Eddy ◽  
Good Agreement

The hydrodynamic instability in an industrial, two-staged, counter-rotative, swirled injector of highly complex geometry is under investigation. Large eddy simulations show that the complicated and strongly nonparallel flow field in the injector is superimposed by a strong precessing vortex core. Mean flow fields of large eddy simulations, validated by experimental particle image velocimetry measurements are used as input for both local and global linear stability analysis. It is shown that the origin of the instability is located at the exit plane of the primary injector. Mode shapes of both global and local linear stability analysis are compared to a dynamic mode decomposition based on large eddy simulation snapshots, showing good agreement. The estimated frequencies for the instability are in good agreement with both the experiment and the simulation. Furthermore, the adjoint mode shapes retrieved by the global approach are used to find the best location for periodic forcing in order to control the precessing vortex core.

scholarly journals Flat vs. curved rigid-lid LES computations of an open-channel confluence

2019 ◽  
Vol 21 (2) ◽  
pp. 318-334 ◽  
Author(s):  
Pedro Xavier Ramos ◽  
Laurent Schindfessel ◽  
João Pedro Pêgo ◽  
Tom De Mulder
Keyword(s):  
Free Surface ◽  
Secondary Flow ◽  
Open Channel ◽  
Pressure Field ◽  
Large Eddy Simulations ◽  
Numerical Treatment ◽  
Mean Flow ◽  
Large Eddy ◽  
Flow Case ◽  
Channel Confluence

Abstract This paper describes the application of four Large Eddy Simulations (LES) to an open-channel confluence flow, making use of a frictionless rigid-lid to treat the free-surface. Three simulations are conducted with a flat rigid-lid, at different elevations. A fourth simulation is carried out with a curved rigid-lid which is a closer approximation to the real free-surface of the flow. The curved rigid-lid is obtained from the time-averaged pressure field on the flat rigid-lid from one of the initial three simulations. The aim is to investigate the limitations of the free-surface treatment by means of a rigid-lid in the simulation of an asymmetric confluence, showing the differences that both approaches produce in terms of mean flow, secondary flow and turbulence. After validation with experimental data, the predictions are used to understand the differences between adopting a flat and a curved rigid-lid onto the confluence hydrodynamics. For the present flow case, although it was characterized by a moderately low downstream Froude number (Fr ≈ 0.37), it was found that an oversimplification of the numerical treatment of the free-surface leads to a decreased accuracy of the predictions of the secondary flow and turbulent kinetic energy.

scholarly journals Three-Dimensional Turbulent Vortex Shedding From a Surface-Mounted Square Cylinder: Predictions With Large-Eddy Simulations and URANS

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
B. A. Younis ◽  
A. Abrishamchi
Keyword(s):  
Experimental Data ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Large Eddy Simulations ◽  
Navier Stokes ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Navier Stokes Equations ◽  
Large Eddy

The paper reports on the prediction of the turbulent flow field around a three-dimensional, surface mounted, square-sectioned cylinder at Reynolds numbers in the range 104–105. The effects of turbulence are accounted for in two different ways: by performing large-eddy simulations (LES) with a Smagorinsky model for the subgrid-scale motions and by solving the unsteady form of the Reynolds-averaged Navier–Stokes equations (URANS) together with a turbulence model to determine the resulting Reynolds stresses. The turbulence model used is a two-equation, eddy-viscosity closure that incorporates a term designed to account for the interactions between the organized mean-flow periodicity and the random turbulent motions. Comparisons with experimental data show that the two approaches yield results that are generally comparable and in good accord with the experimental data. The main conclusion of this work is that the URANS approach, which is considerably less demanding in terms of computer resources than LES, can reliably be used for the prediction of unsteady separated flows provided that the effects of organized mean-flow unsteadiness on the turbulence are properly accounted for in the turbulence model.

Large-Eddy Simulations of Wall Bounded Turbulent Flows Using Unstructured Linear Reconstruction Techniques

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Dario Amirante ◽  
Nicholas J. Hills
Keyword(s):  
Reynolds Number ◽  
Turbulent Flows ◽  
Outer Radius ◽  
Large Eddy Simulations ◽  
Test Cases ◽  
Mean Flow ◽  
Flow Equations ◽  
Turbulent Statistics ◽  
Large Eddy ◽  
Least Squares Approach

Large-eddy simulations (LES) of wall bounded, low Mach number turbulent flows are conducted using an unstructured finite-volume solver of the compressible flow equations. The numerical method employs linear reconstructions of the primitive variables based on the least-squares approach of Barth. The standard Smagorinsky model is adopted as the subgrid term. The artificial viscosity inherent to the spatial discretization is maintained as low as possible reducing the dissipative contribution embedded in the approximate Riemann solver to the minimum necessary. Comparisons are also discussed with the results obtained using the implicit LES (ILES) procedure. Two canonical test-cases are described: a fully developed pipe flow at a bulk Reynolds number Reb = 44 × 103 based on the pipe diameter, and a confined rotor–stator flow at the rotational Reynolds number ReΩ = 4 × 105 based on the outer radius. In both cases, the mean flow and the turbulent statistics agree well with existing direct numerical simulations (DNS) or experimental data.

Study of Afterburning in Solid Rocket Booster Jet: Towards a Model for Afterburning in Large Eddy Simulations

2014 ◽  
Author(s):  
Adèle Poubeau ◽  
Roberto Paoli ◽  
Daniel Cariolle
Keyword(s):  
Three Dimensional ◽  
Axial Direction ◽  
Large Eddy Simulations ◽  
Chemical Mechanism ◽  
Computational Domain ◽  
Time Step ◽  
Simple Method ◽  
Large Eddy ◽  
Solid Rocket ◽  
Comparison Of The Results

This paper focuses on two decisive steps towards Large Eddy Simulation of a solid rocket booster jet. First, three-dimensional Large Eddy Simulations of a non-reactive booster jet including the nozzle were obtained at flight conditions of 20 km of altitude. A particularly long computational domain (400 nozzle exit diameters in the jet axial direction) was simulated, thanks to an innovative local time-stepping method via coupling multi instances of a fluid solver. The dynamics of the jet is analysed and comparison of the results with previous knowledge validates the simulations and confirms that this computational setup can be applied for Large Eddy Simulations of a reactive booster jet. The second part of this paper details the implementation of a simple method to study the hot plume chemistry. Despite its limitations, it is accurate enough to observe the various steps of the chemical mechanism and assess the effect of uncertainties of the rate parameters on chlorine reactions. It was also used to reduce the set of chemical reactions into a short scheme involving a minimum of species and having a limited impact on the physical time step of the Large Eddy Simulations.

Large-Eddy Simulation With Zonal Near Wall Treatment of Flow and Heat Transfer in a Ribbed Duct for the Internal Cooling of Turbine Blades

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Sunil Patil ◽  
Danesh Tafti
Keyword(s):  
Heat Transfer ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
Large Eddy Simulations ◽  
Internal Cooling ◽  
Mean Flow ◽  
Flow And Heat Transfer ◽  
Turbulent Statistics ◽  
Large Eddy ◽  
Near Wall

Large eddy simulations of flow and heat transfer in a square ribbed duct with rib height to hydraulic diameter of 0.1 and 0.05 and rib pitch to rib height ratio of 10 and 20 are carried out with the near wall region being modeled with a zonal two layer model. A novel formulation is used for solving the turbulent boundary layer equation for the effective tangential velocity in a generalized co-ordinate system in the near wall zonal treatment. A methodology to model the heat transfer in the zonal near wall layer in the large eddy simulations (LES) framework is presented. This general approach is explained for both Dirichlet and Neumann wall boundary conditions. Reynolds numbers of 20,000 and 60,000 are investigated. Predictions with wall modeled LES are compared with the hydrodynamic and heat transfer experimental data of (Rau et al. 1998, “The Effect of Periodic Ribs on the Local Aerodynamic and Heat Transfer Performance of a Straight Cooling Channel,”ASME J. Turbomach., 120, pp. 368–375). and (Han et al. 1986, “Measurement of Heat Transfer and Pressure Drop in Rectangular Channels With Turbulence Promoters,” NASA Report No. 4015), and wall resolved LES data of Tafti (Tafti, 2004, “Evaluating the Role of Subgrid Stress Modeling in a Ribbed Duct for the Internal Cooling of Turbine Blades,” Int. J. Heat Fluid Flow 26, pp. 92–104). Friction factor, heat transfer coefficient, mean flow as well as turbulent statistics match available data closely with very good accuracy. Wall modeled LES at high Reynolds numbers as presented in this paper reduces the overall computational complexity by factors of 60–140 compared to resolved LES, without any significant loss in accuracy.

Sign in / Sign up

Export Citation Format

Share Document