Three-dimensionally woven glass fiber composite struts: characterization and mechanical response in tension and compression

2015 ◽  
Vol 50 (1) ◽  
pp. 25-43 ◽  
Author(s):  
Adam J Malcom ◽  
Mark T Aronson ◽  
Haydn NG Wadley
Keyword(s):  
Glass Fiber ◽  
Mechanical Response ◽  
Fiber Composite ◽  
Glass Fiber Composite ◽  
Tension And Compression ◽  
Woven Glass Fiber

Delamination Failure of a Woven Glass Fiber Composite

1997 ◽  
Vol 31 (13) ◽  
pp. 1318-1333 ◽  
Author(s):  
T. Ebeling ◽  
A. Hiltner ◽  
E. Baer ◽  
I. M. Fraser ◽  
M. L. Orton
Keyword(s):  
Glass Fiber ◽  
Fiber Composite ◽  
Glass Fiber Composite ◽  
Woven Glass Fiber ◽  
Delamination Failure

Impact and Flexural Strength of Kaolinite / Glass Fibers Reinforced Heat-Cured Acrylic Denture

2020 ◽  
Vol 1002 ◽  
pp. 340-349
Author(s):  
Wafaa A. Hussain ◽  
Ban Adbul Maseeh Bader ◽  
Muna Y. Slewa ◽  
Luay H. Alwan
Keyword(s):  
Glass Fiber ◽  
Fiber Composite ◽  
Glass Fibers ◽  
Testing Machine ◽  
Tensile Testing Machine ◽  
Denture Base ◽  
Glass Fiber Composite ◽  
Powder Samples ◽  
Materials Used ◽  
Woven Glass Fiber

Nowadays, most materials used to manufacture denture base are heat-cured PMMA, to overcome the low strength of this material, different methods were used to strengthen the denture base and enhanced their properties. This study investigated the effect of glass fiber woven powder kaolinite (Al2Si2O5 (OH) 4) to influence and strength of flexure. Acrylic and kaolinite powders were mixed together and mixed again with acrylic liquid to prepare hybrid composite samples. Woven glass fiber composite was prepared by inserting woven glass fiber between the two halves of the dough. PMMA reinforced by (0, 20) wt% of woven glass fibers or/and (0, 2, 5, 7) wt% of kaolinite powder to prepare eight experimental groups (n= 7). The fractured surface was an evaluation by scanning electron microscope (SEM). X-ray diffraction and Fourier transforminfrared spectra FTIR tests were used to examine kaolinite powder. Samples were tested with the use of a Charpy testing machine for impact test and Instron tensile testing machine for flexural test after storage in water for 10 days at 37 °C. The results showed woven glass fibers with clay powder together significantly increased the mechanical properties of PMMA.

scholarly journals Numerical and Experimental Evaluation of Mechanical and Ring Stiffness Properties of Preconditioning Underground Glass Fiber Composite Pipes

2021 ◽  
Vol 5 (10) ◽  
pp. 264
Author(s):  
Mohamed K. Hassan ◽  
Ahmed F. Mohamed ◽  
Khalil Abdelrazek Khalil ◽  
Mohammed Y. Abdellah
Keyword(s):  
Fracture Toughness ◽  
Finite Element ◽  
Glass Fiber ◽  
Fiber Composite ◽  
Compression Tests ◽  
Glass Fiber Composite ◽  
Before And After ◽  
Tension And Compression ◽  
Edge Notch ◽  
Experimental Findings

The mechanical and ring stiffness of glass fiber pipes are the most determining factors for their ability to perform their function, especially in a work environment with difficult and harmful conditions. Usually, these pipes serve in rough underground environments of desert and petroleum fields; therefore, they are subjected to multi-type deterioration and damage agents. In polymers and composite materials, corrosion is identified as the degradation in their properties. In this study, tension and compression tests were carried out before and after preconditioning in a corrosive agent for 60 full days to reveal corrosion influences. Moreover, the fracture toughness is measured using a standard single edge notch bending. Ring stiffness of such pipes which, are considered characteristic properties, is numerically evaluated using the extended finite element method before and after preconditioning. The results reported that both tensile and compressive strengths degraded nearly more than 20%. Besides the fracture toughness decrease, the stiffness ring strength is reduced, and the finite element results are in good agreement with the experimental findings.

Thermo-Mechanical Response of Hybrid Polymer Composites During Tensile Loading

2017 ◽  
Author(s):  
Raghu V. Prakash ◽  
Monalisha Maharana
Keyword(s):  
Carbon Fiber ◽  
Glass Fiber ◽  
Mechanical Response ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Temperature Response ◽  
Fiber Mats ◽  
Natural Fiber Composite ◽  
Woven Glass Fiber ◽  
Work Done

The fiber reinforced polymers are candidate materials for critical applications in view of the high strength, stiffness characteristics; however, they are highly anisotropic and have complex failure mechanisms. Thermo-mechanical response characterization is one of the means of identifying damage progression in these materials. In this study, tensile tests were conducted on the hybrid composite laminates and Infrared thermographs were used to capture the thermal response of the specimen for the entire range of loading till failure. The tests were conducted on natural fiber composite specimens and hybrid (natural + synthetic fiber) composite specimens. The natural fibers used were in the form of uni-directionally stitched mats of Sunhemp, Kenaf and Flax fiber. The synthetic fibers used were bi-directionally woven Carbon fiber mat and Glass fiber mat. All the laminates were prepared using the hand lay-up technique. Four different configurations of the laminates were prepared. The natural fiber composite laminate comprised of Sunhemp fiber mat in a polyester resin system. The Sunhemp fiber mat was also used with woven Glass fiber mat on one side to prepare an unsymmetrical hybrid laminate. The Kenaf fiber mat was placed between layers of woven Glass fiber mats whereas the flax fiber mat was placed between the woven carbon fiber mats; Epoxy LY 556 and hardener Araldite® was used as the matrix. The finished laminate thickness was 2.1 mm and dog-bone tensile specimens were extracted using a CNC router. Some of the specimens were impacted at low velocities from two different heights to study the change in thermo-mechanical response, post-impact, during tensile test. Temperature response as a function of applied stress, failure strain and work done suggests that there is a correlation between the fracture events that take place during tensile test with the temperature response. In cases where there was a ply-drop failure, the rate of temperature change could identify the failure events, even though the resultant peak temperature was less. When the specimen failed by a single mode of failure (delamination/fiber failure), the temperature rise was found to be proportional to the input work done during tensile testing.

Sign in / Sign up

Export Citation Format

Share Document