Displacement-controlled flexural bending fatigue behavior of graphene/epoxy nanocomposites

2013 ◽  
Vol 48 (24) ◽  
pp. 2935-2944 ◽  
Author(s):  
MM Shokrieh ◽  
M Esmkhani ◽  
F Taheri-Behrooz ◽  
AR Haghighatkhah
Keyword(s):  
Fatigue Behavior ◽  
Epoxy Nanocomposites ◽  
Bending Fatigue

scholarly journals Bending Fatigue Behavior of 17-4 PH Gears Produced by Additive Manufacturing

2021 ◽  
Vol 11 (7) ◽  
pp. 3019
Author(s):  
Franco Concli ◽  
Luca Bonaiti ◽  
Riccardo Gerosa ◽  
Luca Cortese ◽  
Filippo Nalli ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Specific Resistance ◽  
Fatigue Behavior ◽  
Powder Bed ◽  
Bending Fatigue ◽  
Experimental Campaign ◽  
Single Tooth ◽  
Final Failure ◽  
Effective Design ◽  
Resistance Data

The introduction of Additive Manufacturing (AM) is changing the way in which components and machines can be designed and manufactured. Within this context, designers are taking advantage of the possibilities of producing parts via the addition of material, defining strategies, and exploring alternative design or optimization solutions (i.e., nonviable using subtractive technologies) of critical parts (e.g., gears and shafts). However, a safe and effective design requires specific resistance data that, due to the intrinsic modernity of additive technologies, are not always present in the literature. This paper presents the results of an experimental campaign performed on gear-samples made by 17-4 PH and produced via Laser Powder Bed Fusion (PBF-LB/M). The tests were executed using the Single Tooth Bending Fatigue (STBF) approach on a mechanical pulsator. The fatigue limit was determined using two different statistical approaches according to Dixon and Little. The obtained data were compared to those reported in the ISO standard for steels of similar performance. Additional analyses, i.e., Scanning Electron Microscopy SEM, were carried out to provide a further insight of the behavior 17-4PH AM material and in order to investigate the presence of possible defects in the tested gears, responsible for the final failure.

High Cycle Fatigue Behavior of Thermally Oxidized Ti6Al4V Alloy

2007 ◽  
Vol 561-565 ◽  
pp. 2179-2182 ◽  
Author(s):  
Mehmet Cingi ◽  
Onur Meydanoglu ◽  
Hasan Guleryuz ◽  
Murat Baydogan ◽  
Huseyin Cimenoglu ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Yield Strength ◽  
Thermal Oxidation ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Ti6al4v Alloy ◽  
Bending Fatigue ◽  
Rotating Bending Fatigue ◽  
Rotating Bending ◽  
Bending Fatigue Strength

In this study, the effect of thermal oxidation on the high cycle rotating bending fatigue behavior of Ti6Al4V alloy was investigated. Oxidation, which was performed at 600°C for 60 h in air, considerably improved the surface hardness and particularly the yield strength of the alloy without scarifying the tensile ductility. Unfortunately, the rotating bending fatigue strength at 5x106 cycles decreased from about 610 MPa to about 400 MPa upon oxidation. Thus, thermal oxidation leaded a reduction in the fatigue strength of around 34%, while improving the surface hardness (HV0.1) and yield strength 85 % and 36 %, respectively.

Improvement of Fatigue Behaviour of High Strength Aluminium Alloys by Fluidized Bed Peening (FBP)

2007 ◽  
Vol 344 ◽  
pp. 87-96 ◽  
Author(s):  
M. Barletta ◽  
F. Lambiase ◽  
Vincenzo Tagliaferri
Keyword(s):  
Fatigue Life ◽  
Fluidized Bed ◽  
Fatigue Testing ◽  
Fatigue Behavior ◽  
Maximum Amplitude ◽  
High Strength ◽  
Operational Parameters ◽  
Bending Fatigue ◽  
Rotating Bending Fatigue ◽  
Rotating Bending

This paper deals with a definition of a relatively novel technique to improve the fatigue behavior of high strength aluminum alloys, namely, Fluidized Bed Peening (FBP). Fatigue samples made from AA 6082 T6 alloy were chosen according to ASTM regulation about rotating bending fatigue test and, subsequently, treated by varying FBP operational parameters and fatigue testing conditions. First, a full factorial experimental plan was performed to assess the trend of number of cycles to rupture of fatigue samples varying among several experimental levels the factors peening time and maximum amplitude of alternating stress applied to fatigue samples during rotating bending fatigue tests. Second, design of experiment (DOE) technique was used to analyze the influence of FBP operational parameters on fatigue life of AA 6082 T6 alloy. Finally, ruptures of FB treated samples and untreated samples were discussed in order to evaluate the influence of operational parameters on the effectiveness of FBP process and to understand the leading process mechanisms. At any rate, the fatigue behavior of processed components was found to be significantly improved, thereby proving the suitability of FBP process as alternative mechanical technique to enhance fatigue life of components made from high strength aluminum alloy.

Core microstructure-dependent bending fatigue behavior and crack growth of a case-hardened steel

2019 ◽  
Vol 762 ◽  
pp. 138040 ◽  
Author(s):  
H. Farivar ◽  
D. Novokshanov ◽  
S. Richter ◽  
D. Lenz ◽  
W. Bleck ◽  
...  
Keyword(s):  
Crack Growth ◽  
Fatigue Behavior ◽  
Hardened Steel ◽  
Bending Fatigue

On the conjoint influence of broaching and heat treatment on bending fatigue behavior of Inconel 718

2016 ◽  
Vol 671 ◽  
pp. 158-169 ◽  
Author(s):  
Zhe Chen ◽  
Johan J. Moverare ◽  
Ru Lin Peng ◽  
Sten Johansson ◽  
David Gustafsson
Keyword(s):  
Heat Treatment ◽  
Inconel 718 ◽  
Fatigue Behavior ◽  
Bending Fatigue
Sign in / Sign up

Export Citation Format

Share Document