Hydration and microstructure of concrete containing high volume lithium slag

2020 ◽  
Vol 10 (3) ◽  
pp. 430-436
Author(s):  
Zhihai He ◽  
Jingyu Chang ◽  
Shigui Du ◽  
Chaofeng Liang ◽  
Baoju Liu
Keyword(s):  
Mercury Intrusion Porosimetry ◽  
High Volume ◽  
Cementitious Materials ◽  
Pozzolanic Reaction ◽  
Supplementary Cementitious Materials ◽  
Mineral Admixtures ◽  
Sustainable Construction ◽  
Mercury Intrusion ◽  
Variation Trends ◽  
Lithium Slag

Due to requirements for environmental protection, saving of resources and sustainable construction in the future, investigation on the use of high volume mineral admixtures as supplementary cementitious materials in concrete was carried out in this study. The effect of high volume lithium slag (LS) to partially replace cement by weight on compressive strengths of concrete was experimentally investigated, and the hydration of hardened paste was measured by non-evaporable water. Moreover, the microstructure of concrete was determined by mercury intrusion porosimetry and scanning electron microscope methods. Results showed that the use of high volume LS reduced compressive strengths of concrete at early ages, and compressive strengths were remarkably improved at later ages, with concrete containing 40% LS being close to that of the control concrete. Hydration of hardened paste showed similar variation trends with compressive strengths. The highvolume LS degraded concrete microstructure at early ages, and 40% LS improved concrete microstructure at the later ages, due to the filling effect and pozzolanic reaction of LS. However, there still existed defects in microstructure of concrete containing 60% LS, with increased harmful porosity, especially interfacial transition zone.

scholarly journals Pore structure of mortars containing limestone powder and natural pozzolan assessed through mercury intrusion porosimetry and dynamic vapour sorption

2018 ◽  
Vol 199 ◽  
pp. 02020
Author(s):  
Natalia Alderete ◽  
Yury Villagrán ◽  
Arn Mignon ◽  
Didier Snoeck ◽  
Nele De Belie
Keyword(s):  
Pore Structure ◽  
Pore Size ◽  
Mercury Intrusion Porosimetry ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Limestone Powder ◽  
Natural Pozzolan ◽  
Mercury Intrusion ◽  
Vapour Sorption ◽  
Wide Range

Pore structure characterization is a key aspect when studying the durability of cementitious materials. When supplementary cementitious materials (SCMs) are used changes in pore structure are expected, and the complexity of its analysis is increased. The purpose of this paper is to describe the pore structure variation of mortars with two types of SCMs: natural pozzolan from volcanic origin (NP), and limestone powder (LP). We tested mixes with cement replacements (in weight) of 20 % and 40% by NP, and 10 % and 20% by LP. To analyse the pore structure, two widely accepted and complementary techniques were applied: dynamic water vapour sorption (DVS) and mercury intrusion porosimetry (MIP). With the DVS data, the Barret-Joyner-Halenda (BJH) model was used for pore size distribution assessment. Calculations with the Dubinin-Radushkevich (DR) model were also made for the smallest pore size range. Tests were performed at 28 and 90 days. MIP and DVS allowed evaluating the effect of the studied SCMs on different pore size ranges. Both techniques provided comprehensive information over a wide range of pore sizes. The mix with 40 % of NP had the best evolution, showing a significant volume decrease in the mesopore range.

scholarly journals Effect of Hydrogen Nanobubbles on the Mechanical Strength and Watertightness of Cement Mixtures

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1823
Author(s):  
Won-Kyung Kim ◽  
Young-Ho Kim ◽  
Gigwon Hong ◽  
Jong-Min Kim ◽  
Jung-Geun Han ◽  
...  
Keyword(s):  
Mercury Intrusion Porosimetry ◽  
Cement Mortar ◽  
Stable State ◽  
Pozzolanic Reaction ◽  
Hydration Reaction ◽  
High Concentration ◽  
Mercury Intrusion ◽  
Electron Microscope Analysis ◽  
Mixing Water ◽  
Cement Mixtures

This study analyzed the effects of applying highly concentrated hydrogen nanobubble water (HNBW) on the workability, durability, watertightness, and microstructure of cement mixtures. The number of hydrogen nanobubbles was concentrated twofold to a more stable state using osmosis. The compressive strength of the cement mortar for each curing day was improved by about 3.7–15.79%, compared to the specimen that used general water, when two concentrations of HNBW were used as the mixing water. The results of mercury intrusion porosimetry and a scanning electron microscope analysis of the cement paste showed that the pore volume of the specimen decreased by about 4.38–10.26%, thereby improving the watertightness when high-concentration HNBW was used. The improvement in strength and watertightness is a result of the reduction of the microbubbles’ particle size, and the increase in the zeta potential and surface tension, which activated the hydration reaction of the cement and accelerated the pozzolanic reaction.

Use of Algerian Natural Mineral Deposit as Supplementary Cementitious Materials

2018 ◽  
Vol 34 ◽  
pp. 48-58 ◽  
Author(s):  
Karima Arroudj ◽  
Saida Dorbani ◽  
Mohamed Nadjib Oudjit ◽  
Arezki Tagnit-Hamou
Keyword(s):  
Mechanical Strength ◽  
Calcium Hydroxide ◽  
Cement Paste ◽  
Cementitious Materials ◽  
Pozzolanic Reaction ◽  
Heat Of Hydration ◽  
Cement Industry ◽  
Supplementary Cementitious Materials ◽  
Natural Mineral ◽  
Different Ages

Much of the current research on concrete engineering has been focused on including siliceous additions as supplementary cementitious materials (SCMs). Silica reacts with Calcium hydroxide release during cement hydration, and produces more C-S-H. The latter contributes to increase compactness, mechanical strengths and sustainability of concrete. This paper explores the hydration characteristics of cement paste based on various natural mineral additions, that are very abundant in Algeria and present a high silica content (ground natural pozzolana “PZ” and ground dune sand “DS”). For this purpose, several analyses were carried out on modified cement pastes and mortars. TheseSCMswere introduced by replacement levels of 15, 20 and 25 by weight of cement. We first, studied the effect of these SCMs on the heat of hydration and mechanical strength of mortars at different ages. The evolution of hydration of modified paste was studied, by using Thermal analysis (TG/TDA) at different ages, to analyze the Calcium Hydroxide (CH) content of the modified pastes. It is shown that the CH content of the mixes including SCMs is lower than that of the plain cement paste, indicating that silica reacts with the cement paste through a pozzolanic reaction. Increased pozzolanic activity results in higher amounts of Calcium Silicate Hydrate in the paste, which in turn results in higher compressive strength for modified cement mortars. Due to its crystalline morphology, the ground DS particles present a partial pozzolanic effect, compared to PZ which is semi-crystalline. Modified mortars by 20% DS can be the optimal composition. It presents satisfactory results: good mechanical strength and low heat of hydration. It can lead to an economic and sustainable concrete. Ground DS is very abounded in Africa and free of any impurities and can be a good alternativeSCMsin cement industry.

scholarly journals Effect of Graphene Oxide Nanosheets on Physical Properties of Ultra-High-Performance Concrete with High Volume Supplementary Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1929 ◽  
Author(s):  
Yu-You Wu ◽  
Jing Zhang ◽  
Changjiang Liu ◽  
Zhoulian Zheng ◽  
Paul Lambert
Keyword(s):  
Graphene Oxide ◽  
Physical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Slump Flow

Nanomaterials have been increasingly employed for improving the mechanical properties and durability of ultra-high-performance concrete (UHPC) with high volume supplementary cementitious materials (SCMs). Recently, graphene oxide (GO) nanosheets have appeared as one of the most promising nanomaterials for enhancing the properties of cementitious composites. To date, a majority of studies have concentrated on cement pastes and mortars with fewer investigations on normal concrete, ultra-high strength concrete, and ultra-high-performance cement-based composites with a high volume of cement content. The studies of UHPC with high volume SCMs have not yet been widely investigated. This paper presents an experimental investigation into the mini slump flow and physical properties of such a UHPC containing GO nanosheets at additions from 0.00 to 0.05% by weight of cement and a water–cement ratio of 0.16. The study demonstrates that the mini slump flow gradually decreases with increasing GO nanosheet content. The results also confirm that the optimal content of GO nanosheets under standard curing and under steam curing is 0.02% and 0.04%, respectively, and the corresponding compressive and flexural strengths are significantly improved, establishing a fundamental step toward developing a cost-effective and environmentally friendly UHPC for more sustainable infrastructure.

scholarly journals Sustainable low-carbon binders and concretes

2020 ◽  
Vol 166 ◽  
pp. 06007
Author(s):  
Myroslav Sanytsky ◽  
Tetiana Kropyvnytska ◽  
Stanislav Fic ◽  
Hanna Ivashchyshyn
Keyword(s):  
Activity Index ◽  
Chemical Properties ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Cement Matrix ◽  
Low Carbon ◽  
Blended Cements ◽  
Physical And Chemical

Sustainable development depends on a consistency of interests, social, ecological and economic, and that the interests are evaluated in a balanced manner. In order to reduce CO2 emissions, the conception of decreasing clinker factor and increasing the role of supplementary cementitious materials (SCMs) in the cementitious materials has high economical and environmental efficiency. The performance of clinkerefficient blended cements with supplementary cementitious materials were examined. The influence of superfine zeolite with increased surface energy on the physical and chemical properties of low-carbon blended cements is shown. Increasing the dispersion of cementitious materials contributes to the growth of their strength activity index due to compaction of cement matrix and pozzolanic reactions in unclincker part. In consequence of the early structure formation and the directed formation of the microstructure of the cement matrix is solving the problem of obtaining clinker-efficient concretes. Shown that low-carbon blended cements with high volume of SCMs are suitable, in principle, for producing structural concretes.

scholarly journals Ink-bottle Effect and Pore Size Distribution of Cementitious Materials Identified by Pressurization–Depressurization Cycling Mercury Intrusion Porosimetry

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1454 ◽  
Author(s):  
Yong Zhang ◽  
Bin Yang ◽  
Zhengxian Yang ◽  
Guang Ye
Keyword(s):  
Pore Structure ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Mercury Intrusion Porosimetry ◽  
Cementitious Materials ◽  
Limestone Powder ◽  
Accurate Estimation ◽  
Mercury Intrusion ◽  
Pore Size Distributions

Capturing the long-term performance of concrete must be underpinned by a detailed understanding of the pore structure. Mercury intrusion porosimetry (MIP) is a widely used technique for pore structure characterization. However, it has been proven inappropriate to measure the pore size distribution of cementitious materials due to the ink-bottle effect. MIP with cyclic pressurization–depressurization can overcome the ink-bottle effect and enables a distinction between large (ink-bottle) pores and small (throat) pores. In this paper, pressurization–depressurization cycling mercury intrusion porosimetry (PDC-MIP) is adopted to characterize the pore structure in a range of cementitious pastes cured from 28 to 370 days. The results indicate that PDC-MIP provides a more accurate estimation of the pore size distribution in cementitious pastes than the standard MIP. Bimodal pore size distributions can be obtained by performing PDC-MIP measurements on cementitious pastes, regardless of the age. Water–binder ratio, fly ash and limestone powder have considerable influences on the formation of capillary pores ranging from 0.01 to 0.5 µm.

Pulse Velocity Measurements in Fly Ash Blended Cementitious Systems Containing 43 Grade Cement

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
V. M. Sounthararajan ◽  
A. Sivakumar
Keyword(s):  
Fly Ash ◽  
Cost Savings ◽  
Ultrasonic Pulse Velocity ◽  
Cementitious Materials ◽  
Ultrasonic Pulse ◽  
Pozzolanic Reaction ◽  
Pulse Velocity ◽  
Supplementary Cementitious Materials ◽  
Pozzolanic Material ◽  
Cementitious Systems

Investigations on the different supplementary cementitious materials based on the hardening properties and the optimized dosage in cementitious systems find the right choice of pozzolanic material. It is essential to combine various additive/admixtures in concrete in proper proportions to maximize the benefits resulting in cost savings in construction. In the recent years, production technology and composition of hydraulic cements affect the setting and early age behavior of cementitious material. The addition of fly ash in cement is one viable technology to derive maximum benefits in terms of the economy and improved pozzolanic reaction. Ultrasonic pulse velocity testing is a feasible method for evaluating the hardening properties of cementitious materials. In this study, an attempt was made to derive the engineering basis for understanding the development of hardness during hydration of fly ash (FA) based cementitious systems. The tests conducted using pulse velocity technique proved to be an effective method for characterizing the early strength gain properties of different cementitious systems.

Sign in / Sign up

Export Citation Format

Share Document