Novel Nano In2O3—WO3 Composite Films for Ultra Trace Level (ppb) Detection of NO Gas at Room Temperature

2012 ◽  
Vol 17 (1) ◽  
pp. 76-81 ◽  
Author(s):  
I-Chun Yao ◽  
Xiang-Hong Zheng ◽  
Ren-Jang Wu ◽  
Gobalakrishnan Suyambrakasam ◽  
Murthy Chavali
Keyword(s):  
Room Temperature ◽  
Composite Films ◽  
Trace Level ◽  
Ultra Trace

Anatase porous titania nanosheets for resonant-gravimetric detection of ppb-level NO2 at room-temperature

The Analyst ◽  
2021 ◽  
Author(s):  
Jialin Yang ◽  
Ding Wang ◽  
Ming Li ◽  
Haitao Yu ◽  
Pengcheng Xu ◽  
...  
Keyword(s):  
Public Health ◽  
Environmental Protection ◽  
Room Temperature ◽  
Trace Level ◽  
Porous Titania

The trace-level detection to harmful NO2 gas at room-temperature is very important for environmental protection and public health. This paper reports the resonant-gravimetric detection of ppb-level NO2 at room-temperature using...

One step room temperature photodeposition of Cu/TiO2 composite films and its conversion to CuO/TiO2

2009 ◽  
Vol 517 (19) ◽  
pp. 5621-5624 ◽  
Author(s):  
Eilidh Morrison ◽  
David Gutiérrez-Tauste ◽  
Concepción Domingo ◽  
Elena Vigil ◽  
José A. Ayllón
Keyword(s):  
Room Temperature ◽  
Composite Films ◽  
One Step

Structure and magnetotransport properties of Fe3O4–SiO2 composite films reactively sputtered at room temperature

2004 ◽  
Vol 95 (10) ◽  
pp. 5661-5665 ◽  
Author(s):  
Hui Liu ◽  
E. Y. Jiang ◽  
H. L. Bai ◽  
R. K. Zheng
Keyword(s):  
Room Temperature ◽  
Composite Films

scholarly journals A Novel Trace-Level Ammonia Gas Sensing Based on Flexible PAni-CoFe2O4 Nanocomposite Film at Room Temperature

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3077
Author(s):  
Rima D. Alharthy ◽  
Ahmed Saleh
Keyword(s):  
Room Temperature ◽  
Gas Sensing ◽  
Oxidative Polymerization ◽  
Portable Devices ◽  
Trace Level ◽  
Humidity Effect ◽  
Sensor Performance ◽  
Wearable Electronic ◽  
Relative Humidity Effect

In this study, we developed a new chemi-resistive, flexible and selective ammonia (NH3) gas sensor. The sensor was prepared by depositing thin film of polyaniline-cobalt ferrite (PAni-CoFe2O4) nanocomposite on flexible polyethylene terephthalate (PET) through an in situ chemical oxidative polymerization method. The prepared PAni-CoFe2O4 nanocomposite and flexible PET-PAni-CoFe2O4 sensor were evaluated for their thermal stability, surface morphology and materials composition. The response to NH3 gas of the developed sensor was examined thoroughly in the range of 1–50 ppm at room temperature. The sensor with 50 wt% CoFe2O4 NPs content showed an optimum selectivity to NH3 molecules, with a 118.3% response towards 50 ppm in 24.3 s response time. Furthermore, the sensor showed good reproducibility, ultra-low detection limit (25 ppb) and excellent flexibility. In addition, the relative humidity effect on the sensor performance was investigated. Consequently, the flexible PET-PAni-CoFe2O4 sensor is a promising candidate for trace-level on-site sensing of NH3 in wearable electronic or portable devices.

Fabrication and Morphological Characterization of Barium Titanate-Based Polymeric Nanocomposite Thin Films

2018 ◽  
pp. 50-59 ◽  
Author(s):  
Sudhanshu Singh ◽  
Umesh Kumar Dwivedi
Keyword(s):  
Barium Titanate ◽  
Room Temperature ◽  
Composite Films ◽  
Morphological Characterization ◽  
Solution Casting ◽  
Weight Percentage ◽  
Casting Technique ◽  
Nanocomposite Thin Films ◽  
Solution Casting Technique

In this critical review chapter, the authors explain the development of composite films of Barium Titanate (BaTiO3) and Poly (methyl methacrylate) prepared by solution casting technique. Different weight percentage composition of BaTiO3 has been selected to find out the best optimization condition for further investigation and correlate the results. The structural properties have been carried out at room temperature using XRD. Efforts have been made to correlate the results with investigated XRD results of pure BaTiO3 and its composites as observed by other workers at room temperature. The flow of experimental work and microscopic images are explained.

Vapor Deposition of Composite Organic-Inorganic Films

2005 ◽  
Author(s):  
B. Kobrin ◽  
J. Chin ◽  
W. R. Ashurst
Keyword(s):  
Vapor Deposition ◽  
Room Temperature ◽  
Surface Coverage ◽  
Composite Coatings ◽  
Composite Films ◽  
Deposition Process ◽  
Deposition Method ◽  
Self Assembled Monolayer ◽  
Process Sequence ◽  
Inorganic Films

Results on the thermal and immersion stability of ultra-thin composite films created by a deposition method call MVD™ (Molecular Vapor Deposition [1]) are reported. It is observed that these composite films were denser and more stable in thermal and immersion applications when compared to traditional self-assembled monolayer (SAM) films. These improved films were created by a special “sequential” or “layered” deposition process sequence. The MVD™ composite coatings can be deposited at room temperature on a variety of materials such as polymers, fibers, metals, alloys and other materials which normally do not allow films to form with complete surface coverage.

Sign in / Sign up

Export Citation Format

Share Document