A New Method of Errors Loaded Tooth Contact Analysis for Cycloid Bevel Gear

2012 ◽  
Vol 13 (1) ◽  
pp. 690-696
Author(s):  
Zhifeng Liu ◽  
Zhimin Zhang ◽  
Ligang Cai ◽  
Wentong Yang ◽  
Chunhua Guo
Keyword(s):  
Contact Analysis ◽  
Bevel Gear ◽  
New Method ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Loaded Tooth Contact Analysis

A Novel Loaded Tooth Contact Analysis Procedure with Application to Internal-External Straight Bevel Gear Mesh in Pericyclic Drive

2020 ◽  
pp. 1-22
Author(s):  
Tanmay D. Mathur ◽  
Edward C. Smith ◽  
Robert C. Bill
Keyword(s):  
Gear Tooth ◽  
Contact Analysis ◽  
Bevel Gear ◽  
Gear Train ◽  
Initial Surface ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Gear Mesh ◽  
Number Of Teeth ◽  
Loaded Tooth Contact Analysis

Abstract A comprehensive numerical loaded tooth contact analysis (LTCA) model is proposed for straight bevel gears that exhibit large number of teeth in contact, well beyond involute line of action limits. This kind of contact is observed when the meshing gears have conformal surfaces, as in a Pericyclic mechanical transmission, and is traditionally analysed using finite element simulations. The Pericyclic drive is kinematically similar to an epicyclic bevel gear train, and is characterized by load sharing over large number of teeth in an internal-external bevel gear mesh, large shaft angles (175° - 178°), nutational gear motion, and high reduction ratio. The contact region spreads over a large area on the gear tooth flank due to high contacting surface conformity. Thus, a thick plate Finite Strip method (FSM) was utilized to accurately calculate the gear tooth bending deflection. Based on tooth deformation calculation model, and accounting for initial surface separation, a variational framework is developed to simultaneously solve for load distribution and gear tooth deformation. This is followed by calculation of contact stress, bending stress, mesh stiffness, and transmission error. The results demonstrate the high power density capabilities of the Pericyclic drive and potential for gear noise reduction. The model developed herein is applied with real gear tooth surfaces, as well.

Simulation and Experimental Measurement of the Transmission Error of Real Hypoid Gears Under Load

2000 ◽  
Vol 122 (1) ◽  
pp. 109-122 ◽  
Author(s):  
Claude Gosselin ◽  
Thierry Guertin ◽  
Didier Remond ◽  
Yves Jean
Keyword(s):  
Measurement Data ◽  
Simulation Models ◽  
Transmission Error ◽  
Contact Analysis ◽  
Hypoid Gear ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Loaded Tooth Contact Analysis ◽  
Analysis Models

The Transmission Error and Bearing Pattern of a gear set are fundamental aspects of its meshing behavior. To assess the validity of gear simulation models, the Transmission Error and Bearing Pattern of a Formate Hypoid gear set are measured under a variety of operating positions and applied loads. Measurement data are compared to simulation results of Tooth Contact Analysis and Loaded Tooth Contact Analysis models, and show excellent agreement for the considered test gear set. [S1050-0472(00)00901-6]

scholarly journals Lubricated Loaded Tooth Contact Analysis and Non-Newtonian Thermoelastohydrodynamics of High-Performance Spur Gear Transmission Systems

Lubricants ◽  
2020 ◽  
Vol 8 (2) ◽  
pp. 20 ◽  
Author(s):  
Gajarajan Sivayogan ◽  
Ramin Rahmani ◽  
Homer Rahnejat
Keyword(s):  
High Speed ◽  
High Performance ◽  
Spur Gear ◽  
Contact Analysis ◽  
Operating Conditions ◽  
Tooth Contact Analysis ◽  
Transmission Systems ◽  
Tooth Contact ◽  
Contact Kinematics ◽  
Loaded Tooth Contact Analysis

Energy efficiency and functional reliability are the two key requirements in the design of high-performance transmissions. Therefore, a representative analysis replicating real operating conditions is essential. This paper presents the thermoelastohydrodynamic lubrication (TEHL) of meshing spur gear teeth of high-performance racing transmission systems, where high generated contact pressures and lubricant shear lead to non-Newtonian traction. The determination of the input contact geometry of meshing pairs as well as contact kinematics are essential steps for representative TEHL. These are incorporated in the current analysis through the use of Lubricated Loaded Tooth Contact Analysis (LLTCA), which is far more realistic than the traditional Tooth Contact Analysis (TCA). In addition, the effects of lubricant and flash surface temperature rise of contacting pairs, leading to the thermal thinning of lubricant, are taken into account using a thermal network model. Furthermore, high-speed contact kinematics lead to shear thinning of the lubricant and reduce the film thickness under non-Newtonian traction. This comprehensive approach based on established TEHL analysis, particularly including the effect of LLTCA on the TEHL of spur gears, has not hitherto been reported in literature.

Loaded Tooth Contact Analysis of Power-Split Gear Drives Considering Shaft Deformation and Assembly Errors

2015 ◽  
Author(s):  
Siang-Yu Ye ◽  
Shyi-Jeng Tsai
Keyword(s):  
Power Transmission ◽  
Planetary Gear ◽  
Load Sharing ◽  
Contact Analysis ◽  
Influence Coefficient ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Power Split ◽  
Loaded Tooth Contact Analysis ◽  
Compact Design

The power-split gear mechanisms is widely applied in power transmission because of the advantages of compact design, lighter weight and high power density. The load sharing and the load distribution are the important performance issues while designing the power split mechanisms. The paper propose a computerized approach based on the influence coefficient method for loaded tooth contact analysis of such the gear transmission. Not only the load sharing of the multiple contact tooth pairs and the loaded transmission errors, but also the distributed contact stresses and the corresponding contact patterns on all the engaged tooth flanks can be calculated by using the proposed LTCA approach. Some analysis results are also discussed with a study case of the first planetary stage of a compound cycloid planetary gear drive.

Stress Analysis of Spherical Gear Sets

2009 ◽  
Author(s):  
Li-Chi Chao ◽  
Chung-Biau Tsay
Keyword(s):  
Gear Tooth ◽  
Three Dimensional ◽  
Contact Analysis ◽  
Design Parameters ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Contact Points ◽  
Tooth Surfaces ◽  
Loaded Tooth Contact Analysis ◽  
Spherical Gear

The spherical gear is a new type of gear proposed by Mitome et al. [1]. Different from that of the conventional spur or helical gear sets, the spherical gear set can allow variable shaft angles and large axial misalignments without gear interference during the gear drive meshing [1, 2]. Geometrically, the spherical gear has two types of gear tooth profiles, the concave tooth and convex tooth. In practical transmission applications, the contact situation of a spherical gear set is very complex. To obtain a more realistic simulation result, the loaded tooth contact analysis (LTCA) has been performed by employing the finite element method (FEM). According to the derived mathematical model of spherical gear tooth surfaces, an automatic meshes generation program for three-dimensional spherical gears has been developed. Beside, tooth contact analysis (TCA) of spherical gears has been performed to simulate the contact points of the spherical gear set. Furthermore, the contact stress contours of spherical gear tooth surfaces and bending stress of tooth roots have been investigated by giving the design parameters, material properties, loadings and boundary conditions of spherical gears.

Loaded Tooth Contact Analysis and Stresses in Spiral Bevel Gears

2009 ◽  
Author(s):  
Vilmos V. Simon
Keyword(s):  
Contact Pressure ◽  
Angular Position ◽  
Contact Analysis ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Exact Position ◽  
Spiral Bevel ◽  
Loaded Tooth Contact Analysis

The method for loaded tooth contact analysis is applied for the investigation of the influence of misalignments and tooth errors on load distribution, stresses and transmission errors in mismatched spiral bevel gears. By using the corresponding computer program the influence of pinion’s offset and axial adjustment error, angular position error of the pinion axis and tooth spacing error on tooth contact pressure, tooth root stresses and angular displacement of the driven gear member from the theoretically exact position based on the ratio of the numbers of teeth is investigated. The obtained results have shown that in general, the misalignments in spiral bevel gears worsen the conjugation of contacting tooth surfaces and in extreme cases cause edge contact with high tooth contact pressures. But, some mismatches, as are the axial movement of the pinion apex towards the gear teeth or the tip relief of pinion teeth (in this analysis it is represented by the tooth spacing error) reduce the maximum tooth contact pressure. Also it can be concluded that the misalignments and the tooth spacing errors significantly increase the angular position error of the driven gear from the theoretically exact position based on the numbers of teeth and make the motion graphs unbalanced.

Sign in / Sign up

Export Citation Format

Share Document