scholarly journals The Compound Influence of Texture and Microstructure on the Mechanical Properties of Low-C Steel Wires

1991 ◽  
Vol 13 (4) ◽  
pp. 243-260 ◽  
Author(s):  
P. Gangli ◽  
J. A. Szpunar ◽  
Sugondo
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Aspect Ratio ◽  
Yield Strength ◽  
Strain Energy ◽  
Size Parameter ◽  
Wire Axis ◽  
Steel Wires ◽  
The Mean ◽  
Homogeneous Strain

A series of experiments were made determining textural, microstructural, and mechanical properties in cold drawn, and spheroidization heat treated low-C steel wires (AISI-1018 and 1033 grades). It was found that texture exerted a significant influence on the mechanical properties, while microstructure had a comparable influence.Mechanical properties are represented by yield strength (YS), ultimate compressive strength (UCS) and by homogeneous strain energy (EHOM), defined by the integral of stress up to uniform elongation. Textural properties are represented by the Taylor-factor, M, the R-value, and by the maximum of the orientation distribution function (ODFMAX). Micro-structural properties are treated with the help of the aspect ratio parameter (1/√AR), where AR is the grain aspect ratio (length to ellipsoidal width), the grain size parameter (1/√D), and the mean free path between second phase spheroidized cementites √N.For cold drawn steel wires, homogeneous strain energy (EHOM) is well correlated to (1/√AR) and (ODFMAX). Yield strength, on the other hand, appears to be chiefly influenced by the aspect ratio parameter, thus here ODFMAX exerts less influence. The yield strength (YS) of annealed, spheroidization treated low-C wires are equally influenced by the grain size parameter (1/√D), the mean distance between spherulites (√N) and by ODFMAX.The textures of the cold drawn wires could be well described by the 〈110〉 fibre parallel to wire axis, and by the 〈111〉 fibre normal to wire axis. The annealed wires, while also featuring these two fibres, displayed a distinct {111}〈110〉single orientation.

scholarly journals Fabrication of (SiC-AlN)/ZrB2 Composite with Nano-Micron Hybrid Microstructure via PCS-Derived Ceramics Route

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 334
Author(s):  
Aidong Xia ◽  
Jie Yin ◽  
Xiao Chen ◽  
Zhengren Huang ◽  
Xuejian Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Raw Materials ◽  
Secondary Phase ◽  
Pressing Temperature ◽  
Xrd Pattern ◽  
Mean Grain Size ◽  
The Mean

In this work, a (SiC-AlN)/ZrB2 composite with outstanding mechanical properties was prepared by using polymer-derived ceramics (PDCs) and hot-pressing technique. Flexural strength reached up to 460 ± 41 MPa, while AlN and ZrB2 contents were 10 wt%, and 15 wt%, respectively, under a hot-pressing temperature of 2000 °C. XRD pattern-evidenced SiC generated by pyrolysis of polycarbosilane (PCS) was mainly composed by 2H-SiC and 4H-SiC, both belonging to α-SiC. Micron-level ZrB2 secondary phase was observed inside the (SiC-AlN)/ZrB2 composite, while the mean grain size (MGS) of SiC-AlN matrix was approximately 97 nm. This unique nano-micron hybrid microstructure enhanced the mechanical properties. The present investigation provided a feasible tactic for strengthening ceramics from PDCs raw materials.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

scholarly journals Effect of enhanced weld cooling on the mechanical properties of a structural steel with a yield strength of 700 MPa

2020 ◽  
Vol 2 (11) ◽  
Author(s):  
Juhani Laitila ◽  
Lassi Keränen ◽  
Jari Larkiola
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Fatigue Strength ◽  
Impact Toughness ◽  
Yield Strength ◽  
Uniform Elongation ◽  
High Strength ◽  
Low Alloy Steel ◽  
External Cooling ◽  
Welding Processes

AbstractIn this study, we present the effect of enhanced cooling on the mechanical properties of a high-strength low-alloy steel (having a yield strength of 700 MPa) following a single-pass weld process. The properties evaluated in this study include uniform elongation, impact toughness, yield, tensile and fatigue strengths alongside the cooling time of the weld. With the steel used in this study, the enhanced cooling resulted in a weld joint characterized with excellent cross-weld uniform elongation, yield and fatigue strength. The intensified cooling reduced the time it takes for the weld to reach 100 °C by around 190 s. Not only the fusion line of the weld was less pronounced, but also the grain size of the CGHAZ was greatly refined as a result of the enhanced cooling. The results indicate that combining external cooling to the welding processes can be beneficial for the studied high-strength steel.

scholarly journals Microstructure, and Mechanical and Wear Properties of Grp/AZ91 Magnesium Matrix Composites

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1190 ◽  
Author(s):  
Chang-rui Wang ◽  
Kun-kun Deng ◽  
Yan Bai
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Yield Strength ◽  
Wear Mechanism ◽  
Thermal Deformation ◽  
Volume Fraction ◽  
Az91 Alloy

Based on semi-solid mixing technology, two kinds of as-cast Grp (Graphite particles)/AZ91 composites with different Grp volume fractions (5 vol %, 10 vol %) were prepared; these are called 5 vol % Grp/AZ91 composites and 10 vol % Grp/AZ91 composites, respectively. In order to eliminate casting defects, refine grains, and improve mechanical properties, thermal deformation analysis of these composites was conducted. The effect of the addition of Grp and thermal deformation on the microstructure, mechanical properties, and wear resistance of AZ91 composite was explored. The results showed that after 5 vol % Grp was added into the as-cast AZ91 alloy, Mg17Al12 phases were no longer precipitated reticularly along the grain boundary, and Al4C3 phases were formed inside the composite. With the increase in the volume fraction of Grp, the grains of the AZ91 composites were steadily refined. With the increase of forging pass, the grain size of 5% Grp/AZ91 composites decreased first, and then increased. Additionally, the Grp size decreased gradually. There was little change in the yield strength, and the tensile strength and elongation were improved to a certain extent. After forging and extrusion of 5% Grp/AZ91 composites once, the grain size and Grp size were further reduced, and the yield strength, tensile strength, and elongation were increased by 23%, 30%, and 65%, respectively, compared with the composite after forging. With the increase of the number of forging passes before extrusion, the grain size decreased little by little, while the Grp size remained unchanged. The average yield strength, tensile strength, and elongation of the composites after forging and extrusion six times were increased by 3%, 3%, and 23%, respectively, compared with the composite after forging and extrusion once. The wear rate and friction coefficient of the 5% Grp/AZ91 composites decreased after forging once, and the wear mechanism was mainly due to ploughing wear. By comparison, the wear rate and friction coefficient of the 5% Grp/AZ91 composites increased in the extrusion state, and the main wear mechanism was from wedge formation and micro-cutting wear.

Simulation of Fabrication for Single-Phase Al2O3 Ceramic Tool Materials at Different Fabrication Temperature

2010 ◽  
Vol 150-151 ◽  
pp. 1358-1363
Author(s):  
Bin Fang ◽  
Chuan Zhen Huang ◽  
Chong Hai Xu ◽  
Sheng Sun
Keyword(s):  
Mechanical Properties ◽  
Computer Simulation ◽  
Grain Size ◽  
Monte Carlo ◽  
Single Phase ◽  
Two Dimensional ◽  
Ceramic Tool ◽  
Tool Materials ◽  
Mean Grain Size ◽  
The Mean

The fabrication is a key process for the preparation of ceramic tool materials, which governs the mechanical properties of ceramic tool materials under the condition of the same compositions. A computer simulation coupled with fabrication temperature for the hot-pressing process of single-phase ceramic tool materials has been developed using a two-dimensional hexagon lattice model mapped from the realistic microstructure without considering the presence of pores. The fabrication of single-phase Al2O3 is simulated. The mean grain size of simulated microstructure by Monte Carlo Potts model integrated with fabrication temperature increases with an increase in fabrication temperature, which is consistent with the experiment results.

scholarly journals Enhanced Mechanical Properties of Mg-6Sn-3Al-1Zn Alloy with Bimodal Grain Size Disturbed in the Microstructure Uniformly through Changing the Rolling Temperature

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Fuan Wei ◽  
Jinhui Wang ◽  
Ping Li ◽  
Bo Shi
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
Volume Fraction ◽  
Rolling Temperature ◽  
Average Grain Size ◽  
Small Grains ◽  
Mg2sn Phase ◽  
Average Size ◽  
Bimodal Grain Size

The mechanical properties of Mg-6Sn-3Al-1Zn alloy were enhanced with bimodal grain size disturbed in the microstructure uniformly; the Mg-6Sn-3Al-1Zn alloys were rolled with 60% thickness reduction at different rolling temperatures. The results have shown that the Mg-6Sn-3Al-1Zn alloys are composed of Mg2Sn phase and α-Mg matrix phase. When the rolling temperature was less than or equal to 400°C, with the rolling temperature increasing, the average size and volume fraction of Mg2Sn phase and the average grain size of small grains remained unchanged, the average grain size of large grains decreased, the volume fraction of small grains increased, and the yield strength of the alloy increased. When the rolling temperature reached 450°C, the average size and volume fraction of Mg2Sn phase and the average grain size of large grains increased, and the volume fraction of small grains and the yield strength of the alloy decreased. The elongation increased with the rolling temperature increasing, but the change trend of hardness was just opposite. When the alloy was rolled at 400°C, the average sizes of small grains, large grains, and Mg2Sn phases were 3.66 μm, 9.24 μm, and 19.5 μm, respectively. The volume fractions of small grains, large grains, and Mg2Sn phases were 18.6%, 77.6%, and 3.8%, respectively. And the tensile properties reached the optimum; for example, the tensile strength, yield strength, elongation, and Vickers hardness were 361 MPa, 289.5 MPa, 20.5%, and 76.3 HV, respectively.

Mechanical Properties of Porous Nanophase Materials Measured by Instrumental Indentation

1995 ◽  
Vol 400 ◽  
Author(s):  
H. Van Swygenhoven ◽  
W. Wagner ◽  
J. Löffler
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Annealing Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gas Condensation ◽  
Mean Grain Size ◽  
Nanophase Materials ◽  
The Mean ◽  
Instrumental Indentation

AbstractMechanical properties of nanostructured intermetallic Ni3Al synthesized by the inert-gas condensation technique are studied by means of instrumental indentation using the ICT-CSEMEX indenter. This instrument is a microindenter which continously measures load and displacement. Load-displacement curves are performed as function of grain size, consolidation- and annealing temperature. The mean grain size of the samples are studied by means of x-ray diffraction and small-angle neutron scattering.

Grain Size Dependence of Tensile Properties in Cu-Sn Thin Foils (Experimental Study)

2015 ◽  
Vol 736 ◽  
pp. 19-23
Author(s):  
Taek Kyun Jung ◽  
Hyo Soo Lee ◽  
Hyouk Chon Kwon
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Experimental Study ◽  
Grain Size ◽  
Yield Strength ◽  
Room Temperature ◽  
Size Dependence ◽  
Yield Drop ◽  
Thin Foils ◽  
Vacuum Atmosphere

This study was carried out to investigate the effects of grain size on mechanical properties in Cu-Sn foil with a thickness of 30 um. The grain size was varied from approximately 7 um to 50 um using heat treatment at 773 K for 2 h to 24 h in a vacuum atmosphere. Tensile test was carried out at room temperature with strain rate of 1mm/min. Typical yield drop phenomenon was observed. Mechanical properties were found to be strongly affected by microstructural features including grain size. The yield strength and tensile strength gradually decreased with increasing the grain size. The strain to fracture also decreased by grain growth. These results could be explained by not only the grain size dependence of yield strength but also the ratio of thickness to grain size dependence of yield strength.

Evolution of phases during tempering of P91 steel at 760℃ for varying tempering time and their effect on microstructure and mechanical properties

2016 ◽  
Vol 231 (6) ◽  
pp. 1141-1161 ◽  
Author(s):  
C Pandey ◽  
MM Mahapatra
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Secondary Phase ◽  
Particle Spacing ◽  
Carbide Particles ◽  
Tempering Time

In the present investigation, a systematic study has been undertaken with regard to the effects of tempering time on room temperature mechanical properties of P91 (X10CrMoVNNB9-1) steel. Samples cut from P91 (X10CrMoVNNB9-1) industrial pipe were normalized at 1040 ℃ for 40 min and then tempered at 760 ℃ for different tempering times starting from 2 h to 8 h. Detailed analysis of microstructure, particle size, inter-particle spacing, and secondary phase carbide particles of the tempered samples was conducted by secondary electron microscopy technique. Optical microscopy was also utilized to characterize the tempered samples and for the measurement of grain size. In order to reveal the various phases formed during tempering of P91 (X10CrMoVNNB9-1) steel, X-ray diffraction was carried out . To study the fracture surface morphology of tensile tested and impact tested specimen field-emission scanning electron microscopy was carried out. The effect of tempering time on the microstructural parameters revealed an increase in grain size up to 4 h of tempering and then decreased because of recrystallization. The coarsening of secondary phase carbide particles M23C6 was revealed with an increase in tempering time. As a consequence, yield strength, hardness, and ultimate tensile strength were observed to decrease with increase in the tempering time. However, a drastic change was observed in the yield strength, ultimate tensile strength, and toughness after tempering for 6 h. From the present study, it was concluded that optimum combination of yield stress, ultimate tensile strength, hardness, and toughness obtained after tempering at 760 ℃ for 6 h.

Sign in / Sign up

Export Citation Format

Share Document