scholarly journals On the Mass Distribution of Fragments of an Asteroid Disrupted in the Earth’s Atmosphere

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Irina G. Brykina ◽  
Lidia A. Egorova
Keyword(s):  
Mass Distribution ◽  
Mass Fraction ◽  
High Speed ◽  
Power Index ◽  
Outer Space ◽  
Cumulative Number ◽  
Fragment Mass ◽  
Mass Distributions ◽  
High Speed Impact ◽  
Impact Experiments

To model the interaction with the atmosphere of fragments of a disrupted asteroid, which move independently of each other, it is necessary to know their mass distribution. In this regard, an analogy is drawn with fragmentation in high-speed impact experiments performed to simulate the disruption of asteroids at their collisions in outer space. Based on the results of impact experiments and assuming a power law for the mass distribution in a differential form, we obtained the cumulative number of fragments as a function of the fragment mass m normalized to the total mass of fragments, the mass fraction of the largest fragment(s), the number of the largest fragments, and the power index. The formula for the cumulative number of fragments of a disrupted body is used to describe the results of impact experiments for different fragmentation types. The proposed fragment mass distribution is also tested by comparison with the mass distributions of recovered meteorites in the cases of Mbale, Bassikounou, Almahata Sitta, Košice, and Chelyabinsk meteorite falls.

scholarly journals In situ occurrence of Muong Nong-type Australasian tektite fragments from the Quaternary deposits near Huai Om, northeastern Thailand

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Toshihiro Tada ◽  
Ryuji Tada ◽  
Praphas Chansom ◽  
Wickanet Songtham ◽  
Paul A. Carling ◽  
...  
Keyword(s):  
High Speed ◽  
Fractal Dimensions ◽  
Power Laws ◽  
Coarse Fraction ◽  
Rock Fragments ◽  
High Speed Impact ◽  
Similar Chemical ◽  
Impact Experiments ◽  
Northeastern Thailand

Abstract There are several reports of Australasian tektites found within a stratum called “laterite” layer widely distributed in Indochina. However, it has been debated whether these tektites are in situ or reworked. This uncertainty is because a detailed description of their field occurrence is lacking. Here, we describe the detailed occurrence of a cluster of tektite fragments recovered from the “laterite” layer near Huai Om, northeastern Thailand, and demonstrate the evidence of in situ occurrence of the tektites. At least 331 tektite fragments with a total weight of 713 g were found from a 40 × 30 cm area with 10 cm thickness in the uppermost part of the “laterite” layer. The very angular shapes and very poorly sorted nature of the fragments, restoration of larger tektite fragments into one ellipsoidal Muong Nong-type (MN) tektite mass, and the similar chemical composition of the fragments suggest that these MN tektite fragments represent a tektite mass that fragmented in situ. The fact that the fragments were found within the “laterite” layer is inconsistent with a previous interpretation that the upper surface of the “laterite” layer is a paleo-erosional surface, on which the tektites are reworked. The size distribution of the fragments is bi-fractal following two power laws in the range from 10 to 26 mm and from 26 to 37 mm, respectively, with fractal dimensions (Ds) of 2.2 and 7.5. The Ds for the coarse fraction of the tektite fragments is larger than the Ds for rock fragments generated by rockfalls and rock avalanches and similar to the Ds for the coarser fraction fragments generated by high-speed impact experiments, suggesting that the tektite fragments were formed through intense fragmentation by a relatively high energetic process. The occurrence of the fragments forming a cluster indicates that the fragments were not moved apart significantly after fragmentation and burial. Based on these results, we concluded that the mass of a tektite was fragmented at the time of the landing on the ground after traveling a ballistic trajectory and has not been disturbed further.

QELSS diffusion data for moderately broad molar mass distribution polymer samples compared with data from classical gradient techniques

1989 ◽  
Vol 54 (7) ◽  
pp. 1821-1829
Author(s):  
Bedřich Porsch ◽  
Simon King ◽  
Lars-Olof Sundelöf
Keyword(s):  
Diffusion Coefficient ◽  
Mass Distribution ◽  
Molar Mass ◽  
Molar Mass Distribution ◽  
Diffusion Data ◽  
Mass Distributions ◽  
Classical Diffusion ◽  
Polydisperse Polymer

The differences between the QELSS and classical diffusion coefficient of a polydisperse polymer resulting from distinct definitions of experimentally accessible average values are calculated for two assumed specific forms of molar mass distributions. Predicted deviations are compared with the experiment using NBS 706 standard polystyrene. QELSS Dz of this sample relates within 2-4% to the classical diffusion coefficient, if the Schulz-Zimm molar mass distribution is assumed to be valid. In general, differences between the height-area and QELSS diffusion coefficient of about 20% may be found for Mw/Mn ~ 2, and this value may increase above 35%, if strongly tailing molar mass distribution pertains to the sample.

scholarly journals Energy Absorption Characteristics of PVC Coarse Aggregate Concrete under Impact Load

2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Shi Hu ◽  
Huaming Tang ◽  
Shenyao Han
Keyword(s):  
Compressive Strength ◽  
Energy Absorption ◽  
High Speed ◽  
Coarse Aggregate ◽  
Specific Energy Absorption ◽  
Low Speed ◽  
High Speed Impact ◽  
Aggregate Content ◽  
Dynamic Compressive Strength ◽  
Absorption Characteristics

AbstractIn this paper, polyvinyl chloride (PVC) coarse aggregate with different mixing contents is used to solve the problems of plastic pollution, low energy absorption capacity and poor damage integrity, which provides an important reference for PVC plastic concrete used in the initial support structures of highway tunnels and coal mine roadway. At the same time, the energy absorption characteristics and their relationship under different impact loads are studied, which provides an important reference for predicting the energy absorption characteristics of concrete under other PVC aggregate content or higher impact speed. This study replaced natural coarse aggregate in concrete with different contents and equal volume of well-graded flaky PVC particles obtained by crushing PVC soft board. Also, slump, compression, and splitting strength tests, a free falling low-speed impact test of steel balls and a high-speed impact compression test of split Hopkinson pressure bar (SHPB) were carried out. Results demonstrate that the static and dynamic compressive strength decreases substantially, and the elastic modulus and slump decrease slowly with the increase of the mixing amount of PVC aggregate (0–30%). However, the energy absorption rate under low-speed impact and the specific energy absorption per MPa under high-speed impact increase obviously, indicating that the energy absorption capacity is significantly enhanced. Regardless of the mixing amount of PVC aggregate, greater strain rate can significantly enhance the dynamic compressive strength and the specific energy absorption per MPa. After the uniaxial compression test or the SHPB impact test, the relative integrity of the specimen is positively correlated with the mixing amount of PVC aggregate. In addition, the specimens are seriously damaged with the increase of the impact strain rate. When the PVC aggregate content is 20%, the compressive strength and splitting strength of concrete are 33.8 MPa and 3.26 MPa, respectively, the slump is 165 mm, the energy absorption rate under low-speed impact is 89.5%, the dynamic compressive strength under 0.65 Mpa impact air pressure is 58.77 mpa, and the specific energy absorption value per MPa is 13.33, which meets the requirements of shotcrete used in tunnel, roadway support and other impact loads. There is a linear relationship between the energy absorption characteristics under low-speed impact and high-speed impact. The greater the impact pressure, the larger the slope of the fitting straight line. The slope and intercept of the fitting line also show a good linear relationship with the increase of impact pressure. The conclusions can be used to predict the energy absorption characteristics under different PVC aggregate content or higher-speed impact pressure, which can provide important reference for safer, more economical, and environmental protection engineering structure design.

Investigation on the mechanical properties of press-hardened boron steel sheets using the conductive heating technique

2020 ◽  
Vol 234 (8) ◽  
pp. 1084-1098
Author(s):  
O Kocar ◽  
H Livatyalı
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Boron Steel ◽  
Fast Heating ◽  
Heating Method ◽  
Conductive Heating ◽  
Press Hardening ◽  
High Speed Impact ◽  
Significant Difference ◽  
Structural Parts

An aluminized 22MnB5 (Boron) steel sheet, used for structural parts in the automotive industry, was subjected to press-hardening followed by austenitizing, both in a conventional furnace and via the conductive (electric resistance) heating method, an innovative technique based on the Joule’s principle for fast heating of the sheet metal. Conductive heating presents a number of advantages over the in-furnace heating method. These include a more efficient use of energy, as well as the requirement of less time and space for heating, thus lowering costs. After press-hardening was performed using both methods, the microstructural and mechanical characterizations of both specimens were examined for optical microscopy, hardness, tensile strength, and high-speed impact tests. The results showed that the press-hardening process transformed the ferritic–pearlitic microstructure in the as-received state into martensite after die quenching and caused a substantial increase in hardness and strength at the expense of ductility and impact toughness. On the other hand, no significant difference was observed in either the microstructure or mechanical properties with respect to the heating method used. The results obtained in the present investigation concur with the findings of current literature.

High Speed Impact Behaviour of Thermo-Mechanically Processed AA 6082-T6 Thin Plates

2018 ◽  
Vol 5 (9) ◽  
pp. 17203-17212 ◽  
Author(s):  
Rahul Dubey ◽  
Srinivasa Rakesh ◽  
R Velmurugan ◽  
R Jayaganthan
Keyword(s):  
High Speed ◽  
Thin Plates ◽  
Impact Behaviour ◽  
High Speed Impact

Dynamic Force and Torque Analysis of Spherical Four Link Mechanisms

1983 ◽  
Vol 105 (3) ◽  
pp. 492-497 ◽  
Author(s):  
A. T. Yang ◽  
Sun Zhishang
Keyword(s):  
Dynamic Analysis ◽  
Optimum Design ◽  
Mass Distribution ◽  
High Speed ◽  
Dynamic Force ◽  
Arbitrary Mass ◽  
Link Mechanism ◽  
Torque Analysis ◽  
Analytical Expressions

In this paper we present a dynamic analysis of a general spherical four-link mechanism whose links have arbitrary mass distribution. Results, which are in explicit analytical expressions in terms of inertia-induced forces and moments in links, are useful for optimum design of the mechanism under high-speed operation.

Fission fragment mass distributions inCl35+Sm144,154reactions

2015 ◽  
Vol 92 (2) ◽  
Author(s):  
R. Tripathi ◽  
S. Sodaye ◽  
K. Sudarshan ◽  
B. K. Nayak ◽  
A. Jhingan ◽  
...  
Keyword(s):  
Fission Fragment ◽  
Fragment Mass ◽  
Mass Distributions
Sign in / Sign up

Export Citation Format

Share Document