scholarly journals Compaction Quality Inspection Method of Soil-Rock Filled Embankment Based on Continuous Compaction Control Technology

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Zhuoling He ◽  
Junyun Zhang
Keyword(s):  
Deformation Modulus ◽  
Control Points ◽  
Inspection Method ◽  
Continuous Compaction Control ◽  
Compaction Control ◽  
Vibratory Compaction ◽  
The Difference ◽  
Main Basis

Affected by the site construction conditions, the measurement passes of the Taihang Expressway K8 + 105 ∼ K8 + 341 (K8 worksite) in the Taihang Expressway did not meet the requirements of data analysis, and the quantity of the control points was insufficient so that the linear correlation between the dynamic deformation modulus () and the vibratory compaction value (VCV) was not strong. Therefore, the target value of VCV cannot be used to diagnose the E v   d compaction quality of soil-rock filler. This paper analyzes the roller measurement VCV value and in situ measurements E v   d value separately. Results reveal the difference between the VCV mean measured in the last two passes and the standard deviation of the measured VCV mean in the last pass are used as the main basis for the actual compaction quality. In addition, the E v   d mean in the last rolling can be used as an auxiliary judgment basis for the quality control of the compaction.

scholarly journals The 2015–2016 carbon cycle as seen from OCO-2 and the global in situ network

2019 ◽  
Vol 19 (15) ◽  
pp. 9797-9831 ◽  
Author(s):  
Sean Crowell ◽  
David Baker ◽  
Andrew Schuh ◽  
Sourish Basu ◽  
Andrew R. Jacobson ◽  
...  
Keyword(s):  
Carbon Cycle ◽  
Carbon Sink ◽  
Total Carbon ◽  
Transport Models ◽  
New Information ◽  
Global Coverage ◽  
The Difference ◽  
The Tropics

Abstract. The Orbiting Carbon Observatory-2 has been on orbit since 2014, and its global coverage holds the potential to reveal new information about the carbon cycle through the use of top-down atmospheric inversion methods combined with column average CO2 retrievals. We employ a large ensemble of atmospheric inversions utilizing different transport models, data assimilation techniques, and prior flux distributions in order to quantify the satellite-informed fluxes from OCO-2 Version 7r land observations and their uncertainties at continental scales. Additionally, we use in situ measurements to provide a baseline against which to compare the satellite-constrained results. We find that within the ensemble spread, in situ observations, and satellite retrievals constrain a similar global total carbon sink of 3.7±0.5 PgC yr−1, and 1.5±0.6 PgC yr−1 for global land, for the 2015–2016 annual mean. This agreement breaks down in smaller regions, and we discuss the differences between the experiments. Of particular interest is the difference between the different assimilation constraints in the tropics, with the largest differences occurring in tropical Africa, which could be an indication of the global perturbation from the 2015–2016 El Niño. Evaluation of posterior concentrations using TCCON and aircraft observations gives some limited insight into the quality of the different assimilation constraints, but the lack of such data in the tropics inhibits our ability to make strong conclusions there.

scholarly journals Comparison of PM2.5 in Seoul, Korea Estimated from the Various Ground-Based and Satellite AOD

2021 ◽  
Vol 11 (22) ◽  
pp. 10755
Author(s):  
Sang-Min Kim ◽  
Ja-Ho Koo ◽  
Hana Lee ◽  
Jungbin Mok ◽  
Myungje Choi ◽  
...  
Keyword(s):  
Satellite Remote Sensing ◽  
Correlation Coefficients ◽  
Reasonable Accuracy ◽  
High Quality ◽  
Polar Orbit ◽  
Winter Condition ◽  
The Difference ◽  
Mlr Model

Based on multiple linear regression (MLR) models, we estimated the PM2.5 at Seoul using a number of aerosol optical depth (AOD) values obtained from ground-based and satellite remote sensing observations. To construct the MLR model, we consider various parameters related to the ambient meteorology and air quality. In general, all AOD values resulted in the high quality of PM2.5 estimation through the MLR method: mostly correlation coefficients >~0.8. Among various polar-orbit satellite AODs, AOD values from the MODIS measurement contribute to better PM2.5 estimation. We also found that the quality of estimated PM2.5 shows some seasonal variation; the estimated PM2.5 values consistently have the highest correlation with in situ PM2.5 in autumn, but are not well established in winter, probably due to the difficulty of AOD retrieval in the winter condition. MLR modeling using spectral AOD values from the ground-based measurements revealed that the accuracy of PM2.5 estimation does not depend on the selected wavelength. Although all AOD values used in this study resulted in a reasonable accuracy range of PM2.5 estimation, our analyses of the difference in estimated PM2.5 reveal the importance of utilizing the proper AOD for the best quality of PM2.5 estimation.

scholarly journals STUDY OF THE INTEGRATION OF LIDAR AND PHOTOGRAMMETRIC DATASETS BY <i>IN SITU</i> CAMERA CALIBRATION AND INTEGRATED SENSOR ORIENTATION

2017 ◽  
Vol XLII-1/W1 ◽  
pp. 647-652 ◽  
Author(s):  
E. Mitishita ◽  
F. Costa ◽  
M. Martins
Keyword(s):  
Camera Calibration ◽  
Control Points ◽  
Engineering Project ◽  
Integrated Sensor ◽  
Common Procedure ◽  
Sensor Orientation ◽  
The Moment ◽  
High Degree

Photogrammetric and Lidar datasets should be in the same mapping or geodetic frame to be used simultaneously in an engineering project. Nowadays direct sensor orientation is a common procedure used in simultaneous photogrammetric and Lidar surveys. Although the direct sensor orientation technologies provide a high degree of automation process due to the GNSS/INS technologies, the accuracies of the results obtained from the photogrammetric and Lidar surveys are dependent on the quality of a group of parameters that models accurately the user conditions of the system at the moment the job is performed. This paper shows the study that was performed to verify the importance of the in situ camera calibration and Integrated Sensor Orientation without control points to increase the accuracies of the photogrammetric and LIDAR datasets integration. The horizontal and vertical accuracies of photogrammetric and Lidar datasets integration by photogrammetric procedure improved significantly when the Integrated Sensor Orientation (ISO) approach was performed using Interior Orientation Parameter (IOP) values estimated from the in situ camera calibration. The horizontal and vertical accuracies, estimated by the Root Mean Square Error (RMSE) of the 3D discrepancies from the Lidar check points, increased around of 37% and 198% respectively.

scholarly journals The 2015–2016 Carbon Cycle As Seen from OCO-2 and the Global <i>In Situ</i> Network

2019 ◽  
Author(s):  
Sean Crowell ◽  
David Baker ◽  
Andrew Schuh ◽  
Sourish Basu ◽  
Andrew R. Jacobson ◽  
...  
Keyword(s):  
Carbon Cycle ◽  
Carbon Sink ◽  
Total Carbon ◽  
Transport Models ◽  
New Information ◽  
Global Coverage ◽  
The Difference ◽  
The Tropics

Abstract. The Orbiting Carbon Observatory-2 has been on orbit since 2014, and its global coverage holds the potential to reveal new information about the carbon cycle through the use of top-down atmospheric inversion methods combined with column average CO2 retrievals. We employ a large ensemble of atmospheric inversions utilizing different transport models, data assimilation techniques and prior flux distributions in order to quantify the satellite-informed fluxes from OCO-2 Version 7r land observations and their uncertainties at continental scales. Additionally, we use in situ measurements to provide a baseline against which to compare the satellite-constrained results. We find that within ensemble spread, in situ observations and satellite retrievals constrain a similar global total carbon sink of 3.7 ± 0.5 PgC, and 1.5 ± 0.6 PgC per year for global land, for the 2015–2016 annual mean. This agreement breaks down on smaller regions, and we discuss the differences between the experiments. Of particular interest is the difference between the different assimilation constraints in the tropics, with the largest differences occurring in tropical Africa, which could be an indication of the global perturbation from the 2015–2016 El Niño. Evaluation of posterior concentrations using TCCON and aircraft observations gives some limited insight into the quality of the different assimilation constraints, but the lack of such data in the tropics inhibits our ability to make strong conclusions there.

Assessing soil compaction using continuous compaction control and location-specific in situ tests

2017 ◽  
Vol 73 ◽  
pp. 31-44 ◽  
Author(s):  
Christopher L. Meehan ◽  
Daniel V. Cacciola ◽  
Faraz S. Tehrani ◽  
William J. Baker
Keyword(s):  
Soil Compaction ◽  
In Situ Tests ◽  
Continuous Compaction Control ◽  
Compaction Control

A Comparison of Continuous Compaction Control Measurements with Localized In Situ Test Results

IFCEE 2018 ◽  
2018 ◽  
Author(s):  
Daniel V. Cacciola ◽  
Christopher L. Meehan ◽  
William J. Baker ◽  
Faraz S. Tehrani
Keyword(s):  
Test Results ◽  
In Situ Test ◽  
Continuous Compaction Control ◽  
Compaction Control

Letter to the Editor: The Continuing Challenge of Evaluating RSD Impairment and Disability

1998 ◽  
Vol 3 (5) ◽  
pp. 8-10
Author(s):  
Robert L. Knobler ◽  
Charles N. Brooks ◽  
Leon H. Ensalada ◽  
James B. Talmage ◽  
Christopher R. Brigham
Keyword(s):  
Disability Evaluation ◽  
Body Part ◽  
Loss Of Function ◽  
Regulatory Requirements ◽  
Major Cardiac Event ◽  
Clinical Scenarios ◽  
Impairment Score ◽  
Occupational Activities ◽  
The Difference

Abstract The author of the two-part article about evaluating reflex sympathetic dystrophy (RSD) responds to criticisms that a percentage impairment score may not adequately reflect the disability of an individual with RSD. The author highlights the importance of recognizing the difference between impairment and disability in the AMA Guides to the Evaluation of Permanent Impairment (AMA Guides): impairment is the loss, loss of use, or derangement of any body part, system, or function; disability is a decrease in or the loss or absence of the capacity to meet personal, social, or occupational demands or to meet statutory or regulatory requirements because of an impairment. The disparity between impairment and disability can be encountered in diverse clinical scenarios. For example, a person's ability to resume occupational activities following a major cardiac event depends on medical, social, and psychological factors, but nonmedical factors appear to present the greatest impediment and many persons do not resume work despite significant improvements in functional capacity. A key requirement according to the AMA Guides is objective documentation, and the author agrees that when physicians consider the disability evaluation of people, more issues than those relating to the percentage loss of function should be considered. More study of the relationships among impairment, disability, and quality of life in patients with RSD are required.

COMBINATORIAL POLYNOMIALLY COMPUTABLE CHARACTERISTICS OF SUBSTITUTIONS AND THEIR PROPERTIES

2020 ◽  
Vol 7 (2) ◽  
pp. 34-41
Author(s):  
VLADIMIR NIKONOV ◽  
◽  
ANTON ZOBOV ◽  
Keyword(s):  
Mathematical Expectation ◽  
Point Of View ◽  
Small Range ◽  
Computational Point ◽  
Wide Range ◽  
Bijective Function ◽  
The Difference ◽  
Element Base ◽  
Selection Of

The construction and selection of a suitable bijective function, that is, substitution, is now becoming an important applied task, particularly for building block encryption systems. Many articles have suggested using different approaches to determining the quality of substitution, but most of them are highly computationally complex. The solution of this problem will significantly expand the range of methods for constructing and analyzing scheme in information protection systems. The purpose of research is to find easily measurable characteristics of substitutions, allowing to evaluate their quality, and also measures of the proximity of a particular substitutions to a random one, or its distance from it. For this purpose, several characteristics were proposed in this work: difference and polynomial, and their mathematical expectation was found, as well as variance for the difference characteristic. This allows us to make a conclusion about its quality by comparing the result of calculating the characteristic for a particular substitution with the calculated mathematical expectation. From a computational point of view, the thesises of the article are of exceptional interest due to the simplicity of the algorithm for quantifying the quality of bijective function substitutions. By its nature, the operation of calculating the difference characteristic carries out a simple summation of integer terms in a fixed and small range. Such an operation, both in the modern and in the prospective element base, is embedded in the logic of a wide range of functional elements, especially when implementing computational actions in the optical range, or on other carriers related to the field of nanotechnology.

Pengaruh Jenis Co-Solvent terhadap Rendemen dan Mutu Biodiesel secara Transesterifikasi In Situ Menggunakan Radiasi Gelombang Mikro

2016 ◽  
Vol 10 (2) ◽  
pp. 119-126
Author(s):  
Mahlinda Mahlinda ◽  
Fitriana Djafar
Keyword(s):  
Catalyst Concentration ◽  
Maximum Yield ◽  
Acid Value ◽  
Experimental Result ◽  
In Situ Transesterification ◽  
Yield And Quality ◽  
Solvent Type ◽  
Biodiesel Quality

The main purpose of this research was to observer effect co-solvent type (n-Hexane, chloroform and without co-solvent)  toward yield and quality of biodiesel via in situ transesterification process using microwave irradiation. The process was studied at microwave power 450 watt, reaction time 4 minutes, methanol to seed ratio 25:1 and catalyst concentration 5%. The physicochemical parameters of the biodiesel produced such as viscosity, density and acid value were analysed and compared with the SNI 7182-2012 standard. The experimental result showed the maximum yield biodiesel 78,32% obtained by using co-solvent chloroform.Test result of physicochemical properties (viscosity, density and acid value) of biodiesel products using co solvent n-Hexane, chloroform and without co solvent showed that these products conform to the SNI 7182-2012 standars. The type of co-solvent only affectedon biodiesel yield dan not affected on biodiesel quality (viscosity, density and acid value).  ABSTRAKTujuan penelitian ini adalah untuk mempelajari pengaruh jenis co-solvent (n-Hexane, chloroform dan tanpa co-solvent) terhadap rendemen dan mutu biodiesel secara trasesterifikasi in situ menggunakan radiasi gelombang mikro. Proses dilakukan pada daya gelombang mikro 450 watt, waktu reaksi 4 menit, perbandingan berat metanol terhadap bahan baku 25:1 dan jumlah katalis 5%. Parameter fisiko kimia dari produk biodiesel seperti viskositas, densitas dan angka asam di analisa dan dibandingkan dengan standar SNI 7182-2012 tentang biodiesel. Hasil penelitian menunjukkan rendemen maksimum biodiesel sebesar 78,32% diperoleh dengan menggunakan co-solvent chloroform. Hasil pengujian  karakteristik fisiko kimia (viskositas, densitas dan angka asam) dari produk biodiesel menggunakan co-solvent n-Hexane, chloroform dan tanpa co-solvent menunjukkan bahwa semua parameter ini masih memenuhi standar SNI 1782-2012 tentang biodiesel. Jenis co-solvent hanya berpengaruh pada rendemen biodiesel dan tidak berpengaruh terhadap mutu biodiesel (viskositas, densitas dan bilangan asam).Kata kunci: co-solvent, in situ transesterifikasi, microwave, rendemen, mutu   

Sign in / Sign up

Export Citation Format

Share Document