scholarly journals Hardware Sharing for Channel Interleavers in 5G NR Standard

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Xiaokang Xiong ◽  
Yuhang Dai ◽  
Zhuhua Hu ◽  
Kejia Huo ◽  
Yong Bai ◽  
...  
Keyword(s):  
Fading Channels ◽  
Hardware Implementation ◽  
Transmission Efficiency ◽  
Polar Codes ◽  
Data Channel ◽  
Channel Codes ◽  
New Radio ◽  
The Cost ◽  
And Control ◽  
Hardware Sharing

Interleaver module is an important part of modern mobile communication system. It plays an important role in reducing bit error rate and improving transmission efficiency over fading channels. In 5G NR (5th Generation New Radio) standards, LDPC (low-density parity-check) and polar channel codes are employed for data channels and control channels, respectively. If multiple interleavers are implemented separately for them, the cost increases significantly. To address this issue, a hardware multiplexing scheme for channel interleavers based on LDPC and polar codes is proposed in this paper. Firstly, the formulas for the processes of the control channel interleaving and data channel interleaving are derived with respect to 5G NR standard. Then, the hardware implementation structures of the two interleavers are given. Subsequently, hardware reuse is proposed by sharing the similar or identical parts between the two hardware structures. Simulation results verify the correctness of our proposed scheme and demonstrate that it can realize the hardware sharing of the two kinds of channel interleavers to reduce the cost of silicon.

Sensor System based on in-fiber Bragg Grats and Interrogator with Spectral Time Channel Separation

2021 ◽  
Vol 23 (5) ◽  
pp. 247-254
Author(s):  
I.L. Borisenkov ◽  
◽  
K.E. Voronov ◽  
G.I. Leonovich ◽  
M.P. Kalayev ◽  
...  
Keyword(s):  
Hardware Implementation ◽  
Sensor System ◽  
Test Results ◽  
Monitoring And Control ◽  
Board Monitoring ◽  
Monitoring And Control Systems ◽  
Software And Hardware ◽  
Channel Separation ◽  
The Cost ◽  
And Control

The principle of construction and a variant of the software and hardware implementation of the sensor system based on intra-fiber Bragg gratings (FBG) by the example of temperature measurement are proposed. The use of spectral-time separation of measuring channels, which takes into account the features of the functioning and placement of sensors based on FBGs, can significantly reduce the cost, dimensions, weight and power consumption of the interrogator, and neutralize the difficulties in setting up and periodic calibration typical for serial products. The test results of the system show the directions and prospects of using the developed equipment as part of portable and on-board monitoring and control systems.

scholarly journals Multi-Blockchain-Based IoT Data Processing Techniques to Ensure the Integrity of IoT Data in AIoT Edge Computing Environments

Sensors ◽  
2021 ◽  
Vol 21 (10) ◽  
pp. 3515
Author(s):  
Sung-Ho Sim ◽  
Yoon-Su Jeong
Keyword(s):  
Low Cost ◽  
Third Party ◽  
Monitoring And Control ◽  
Constant Size ◽  
Computing Environments ◽  
Iot Devices ◽  
Cloud Servers ◽  
The Cost ◽  
Processing Techniques ◽  
And Control

As the development of IoT technologies has progressed rapidly recently, most IoT data are focused on monitoring and control to process IoT data, but the cost of collecting and linking various IoT data increases, requiring the ability to proactively integrate and analyze collected IoT data so that cloud servers (data centers) can process smartly. In this paper, we propose a blockchain-based IoT big data integrity verification technique to ensure the safety of the Third Party Auditor (TPA), which has a role in auditing the integrity of AIoT data. The proposed technique aims to minimize IoT information loss by multiple blockchain groupings of information and signature keys from IoT devices. The proposed technique allows IoT information to be effectively guaranteed the integrity of AIoT data by linking hash values designated as arbitrary, constant-size blocks with previous blocks in hierarchical chains. The proposed technique performs synchronization using location information between the central server and IoT devices to manage the cost of the integrity of IoT information at low cost. In order to easily control a large number of locations of IoT devices, we perform cross-distributed and blockchain linkage processing under constant rules to improve the load and throughput generated by IoT devices.

In-line filtration reduced phlebitis associated with peripheral venous cannulation: Focus on cost-effectiveness and patients’ perspectives

2019 ◽  
Vol 21 (2) ◽  
pp. 154-160
Author(s):  
Gianluca Villa ◽  
Rosa Giua ◽  
Timothy Amass ◽  
Lorenzo Tofani ◽  
Cosimo Chelazzi ◽  
...  
Keyword(s):  
Cost Effectiveness ◽  
Vascular Access ◽  
Cost Effective ◽  
Causative Factor ◽  
Control Group ◽  
Previous Trial ◽  
Venous Cannulation ◽  
Group A ◽  
The Cost ◽  
And Control

Background: In a previous trial, in-line filtration significantly prevented postoperative phlebitis associated with short peripheral venous cannulation. This study aims to describe the cost-effectiveness of in-line filtration in reducing phlebitis and examine patients’ perception of in-hospital vascular access management with and without in-line filtration. Methods: We analysed costs associated with in-line filtration: these data were prospectively recorded during the previous trial. Furthermore, we performed a follow-up for all the 268 patients enrolled in this trial. Among these, 213 patients responded and completed 6 months after hospital discharge questionnaires evaluating the perception of and satisfaction with the management of their vascular access. Results: In-line filtration group required 95.60€ more than the no-filtration group (a mean of € 0.71/patient). In terms of satisfaction with the perioperative management of their short peripheral venous cannulation, 110 (82%) and 103 (76.9%) patients, respectively, for in-line filtration and control group, completed this survey. Within in-line filtration group, 97.3% of patients were satisfied/strongly satisfied; if compared with previous experiences on short peripheral venous cannulation, 11% of them recognised in-line filtration as a relevant causative factor in determining their satisfaction. Among patients within the control group, 93.2% were satisfied/strongly satisfied, although up to 30% of them had experienced postoperative phlebitis. At the qualitative interview, they recognised no difference than previous experiences on short peripheral venous cannulation, and mentioned postoperative phlebitis as a common event that ‘normally occurs’ during a hospital stay. Conclusion: In-line filtration is cost-effective in preventing postoperative phlebitis, and it seems to contribute to increasing patient satisfaction and reducing short peripheral venous cannulation–related discomfort

scholarly journals An overview of channel coding for 5G NR cellular communications

2019 ◽  
Vol 8 ◽  
Author(s):  
Jung Hyun Bae ◽  
Ahmed Abotabl ◽  
Hsien-Ping Lin ◽  
Kee-Bong Song ◽  
Jungwon Lee
Keyword(s):  
Channel Coding ◽  
Ldpc Codes ◽  
Low Latency ◽  
Polar Codes ◽  
Coding Scheme ◽  
Coding Schemes ◽  
Successive Cancellation ◽  
New Radio ◽  
Key Characteristics ◽  
User Data

AbstractA 5G new radio cellular system is characterized by three main usage scenarios of enhanced mobile broadband (eMBB), ultra-reliable and low latency communications (URLLC), and massive machine type communications, which require improved throughput, latency, and reliability compared with a 4G system. This overview paper discusses key characteristics of 5G channel coding schemes which are mainly designed for the eMBB scenario as well as for partial support of the URLLC scenario focusing on low latency. Two capacity-achieving channel coding schemes of low-density parity-check (LDPC) codes and polar codes have been adopted for 5G where the former is for user data and the latter is for control information. As a coding scheme for data, 5G LDPC codes are designed to support high throughput, a variable code rate and length and hybrid automatic repeat request in addition to good error correcting capability. 5G polar codes, as a coding scheme for control, are designed to perform well with short block length while addressing a latency issue of successive cancellation decoding.

scholarly journals Dynamic Analysis and Control of an Automatic Transmission for Start-Stop Function and Efficiency Improvement

2015 ◽  
Vol 2015 ◽  
pp. 1-13
Author(s):  
Yang Liu ◽  
Shuhan Wang ◽  
Peng Dong ◽  
Xiangyang Xu
Keyword(s):  
Control Strategies ◽  
Automatic Transmission ◽  
Simulation Method ◽  
Transmission Efficiency ◽  
The Novel ◽  
Test Results ◽  
Test Environment ◽  
Pump System ◽  
Oil Pump ◽  
And Control

An electric oil pump (EOP) was integrated into the hydraulic system and an automatic transmission (AT) mechanical oil pump (MOP) was downsized. These processes were performed to combine a start-stop function with the AT and further improve the transmission efficiency. Furthermore, this study established a dynamics model of power loss and leakage of an 8-speed AT; a flow-based control algorithm of the EOP was then developed to realize the start-stop function and support the MOP to meet the flow requirement of the system. Based on a driving simulation method, sizes of the MOP and EOP that ensured optimal fuel economy were selected. A control strategy for the starting clutch was also developed to minimize the starting delay of the test vehicle. A test environment on a rig and prototype vehicle was established to verify the feasibility of the proposed control strategies. The test results indicated that the transmission functioned favorably with the novel two-pump system presented, and a quick and smooth starting performance was achieved when the engine was restarted. The findings in this study are extremely valuable for forward designs of an AT for realizing start-stop function and improving efficiency.

Synergetic Concept of Software Control of Machining Processes on Metal-Cutting Machines

2021 ◽  
pp. 24-36
Author(s):  
V.L. Zakovorotny ◽  
V.E. Gvindzhiliya
Keyword(s):  
Tool Wear ◽  
Metal Cutting ◽  
Wear Testing ◽  
External Control ◽  
Machining Processes ◽  
Cutting Zone ◽  
Output Characteristics ◽  
The Cost ◽  
And Control ◽  
Cutting System

High precision metal-cutting machines ensure that the programmed machine actuator trajectories correspond to the real ones. For lathes these are the trajectories of the longitudinal and transverse calipers of the system, as well as the spindle. The purpose of processing is to produce parts of a given quality while minimizing the manufacturing costs. The condition of the dynamic cutting system, determined by the trajectories of forces and deformations, affects the quality indicators of parts and the cutting efficiency, which depends on the intensity of tool wear. The properties of the system change depending on the phase trajectory of the power of irreversible transformations of the energy supplied to the cutting zone by the work performed. Their changes related with the evolution of the parameters of the dynamic link formed by cutting are manifested in the development of tool wear and changes in the quality of the part. Thus, the power of irreversible energy transformations is one of the internal factors causing changes in the output characteristics of processing and the state of the process. In this regard, when processing on machine tools, there is a problem of synergistic coordination of external control (for example, the CNC program) with internal one, the source of which is the irreversible transformation of the energy supplied to the cutting zone. The article considers the problem of synergetic coordination of external and internal controls during cutting process, the solution of which will allow increasing the efficiency of processing on CNC machines. A mathematical model of a controlled dynamic cutting system and control algorithms are proposed to improve the efficiency of processing parts of a given quality while minimizing the intensity of tool wear. Testing of the developed algorithms has shown that their use reduces the cost of manufacturing parts by 1.2.

Cost-Effectiveness of Paving Fabrics Used to Control Reflective Cracking

2000 ◽  
Vol 1730 (1) ◽  
pp. 139-149 ◽  
Author(s):  
William G. Buttlar ◽  
Diyar Bozkurt ◽  
Barry J. Dempsey
Keyword(s):  
Life Cycle ◽  
Cost Effectiveness ◽  
Department Of Transportation ◽  
Reflective Cracking ◽  
Crack Control ◽  
Condition Rating ◽  
System A ◽  
Rigid Pavements ◽  
The Cost ◽  
And Control

The Illinois Department of Transportation (IDOT) spends $2 million annually on reflective crack control treatments; however, the cost-effectiveness of these treatments had not been reliably determined. A recent study evaluated the cost-effectiveness of IDOT reflective crack control System A, which consists of a nonwoven polypropylene paving fabric, placed either in strips longitudinally over lane-widening joints or over the entire pavement (area treatment). The study was limited to projects constructed originally as rigid pavements and subsequently rehabilitated with one or more bituminous overlays. Performance of 52 projects across Illinois was assessed through crack mapping and from distress and serviceability data in IDOT’s condition rating survey database. Comparisons of measured reflective cracking in treated and control sections revealed that System A retarded longitudinal reflective widening crack development, but it did not significantly retard transverse reflective cracking, which agrees with earlier studies. However, both strip and area applications of these fabric treatments appeared to improve overall pavement serviceability, and they were estimated to increase rehabilitation life spans by 1.1 and 3.6 years, respectively. Reduction in life-cycle costs was estimated to be 4.4 and 6.2 percent when placed in medium and large quantities, respectively, and to be at a break-even level for small quantities. However, life-cycle benefits were found to be statistically insignificant. Limited permeability testing of field cores taken on severely distressed transverse joints suggested that waterproofing benefits could exist even after crack reflection. This was consistent with the observation that, although serviceability was generally improved with area treatment, crack reflection was not retarded relative to untreated areas.

scholarly journals Cost-effectiveness of two long-lasting insecticidal nets delivery models in mass campaign in rural Mozambique

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Jorge A. H. Arroz ◽  
Baltazar Candrinho ◽  
Chandana Mendis ◽  
Melanie Lopez ◽  
Maria do Rosário O. Martins
Keyword(s):  
Cost Effectiveness ◽  
Cost Effective ◽  
Universal Coverage ◽  
Cost Effectiveness Ratio ◽  
Net Benefit ◽  
Incremental Net Benefit ◽  
The Cost ◽  
And Control ◽  
Delivery Models ◽  
Long Lasting Insecticidal Nets

Abstract Objective The aim is to compare the cost-effectiveness of two long-lasting insecticidal nets (LLINs) delivery models (standard vs. new) in universal coverage (UC) campaigns in rural Mozambique. Results The total financial cost of delivering LLINs was US$ 231,237.30 and US$ 174,790.14 in the intervention (302,648 LLINs were delivered) and control districts (219,613 LLINs were delivered), respectively. The average cost-effectiveness ratio (ACER) per LLIN delivered and ACER per household (HH) achieving UC was lower in the intervention districts. The incremental cost-effectiveness ratio (ICER) per LLIN and ICER per HH reaching UC were US$ 0.68 and US$ 2.24, respectively. Both incremental net benefit (for delivered LLIN and for HHs reaching UC) were positive (intervention deemed cost-effective). Overall, the newer delivery model was the more cost-effective intervention. However, the long-term sustainability of either delivery models is far from guaranteed in Mozambique’s current economic context.

scholarly journals PENGGUNAAN STANDARD WBS (WORK BREAKDOWN STRUCTURE) PADA PROYEK BANGUNAN GEDUNG

2019 ◽  
Vol 5 (1) ◽  
pp. 29-34
Author(s):  
Ayu Herzanita
Keyword(s):  
Current Problem ◽  
Construction Project ◽  
Project Performance ◽  
Work Package ◽  
Building Projects ◽  
Work Breakdown Structure ◽  
Time Performance ◽  
The Cost ◽  
And Control ◽  
Method Approach

WBS (Work Breakdown Structure) plays an important role in every construction project. WBS is a hierarchy of decreasing scope of work to become the smallest level called a work package, making it easier in the process of project management and control. The current problem is that many contractors in Indonesia, both large and small contractors, do not understand the importance of using WBS in a construction project. This causes project performance to be less than optimal, especially on cost and time performance. Currently, WBS standards have been developed for building projects. In this study will look at the cost and time performance of the project from the use of WBS standard building. The sample used in this study are projects that have applied the use of project standards. The projects include Building X, Lecture Building Y, and Sports Facility Building Z. The method used in this study is the EVM (Earn Value Method) approach, collecting data using questionnaires. The results showed that using the WBS standard had an effect on cost and time performance. Good cost and time performance is shown in the Building X and Lecture Y buildings. While the cost and time performance of the Z Sports Facility Building tends to be unstable. This is because the work items that exist in the WBS standard are not in accordance with the project conditions, so it is necessary to adjust work items.

Sign in / Sign up

Export Citation Format

Share Document