scholarly journals Enhancement in Optical Properties of Lanthanum-Doped Manganese Barium Hexaferrites under Different Substitutions

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Meshal Alzaid
Keyword(s):  
Permanent Magnets ◽  
Electronic Devices ◽  
Barium Hexaferrite ◽  
Band Gap Energy ◽  
Degree Of Crystallinity ◽  
Magnetic Recording Media ◽  
X Ray Diffraction ◽  
Communication Devices ◽  
Ft Ir ◽  
The Degree Of Crystallinity

The permeability and electrical resistivity of barium hexaferrite magnetic materials can be used in various products such as magnetic recording media, computers, electronic devices, materials for permanent magnets, and communication devices. This work focuses on the synthesis of rare earth lanthanum (La3+)-doped manganese in barium hexaferrite (Ba1−xLaxMnyFe12−yO19) (x = 0.02–0.10 and y = 0.02–0.10) prepared by using the coprecipitation method. The intensity peak is increased with increasing the concentration of lanthanum, which shows the enhancement in the degree of crystallinity and increase in the size of crystallite. The band gap energy decreased gradually with the increase of concentration of lanthanum. The micrographs observed that the material is basically made up of some rings or rods such as particles in pure La-Ma in barium hexaferrite. The agglomeration was observed because of heat behavior at 600°C or may be concentration effect. The structural studies are done using X-ray diffraction, UV, FT-IR, and SEM techniques.

scholarly journals Polyurethane Composite Foams Synthesized Using Bio-Polyols and Cellulose Filler

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3474
Author(s):  
Katarzyna Uram ◽  
Milena Leszczyńska ◽  
Aleksander Prociak ◽  
Anna Czajka ◽  
Michał Gloc ◽  
...  
Keyword(s):  
Cross Sections ◽  
Raw Materials ◽  
Polyurethane Foams ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Polyurethane Composite ◽  
Composite Foams ◽  
Closed Cell ◽  
Ft Ir ◽  
The Fourier Transform

Rigid polyurethane foams were obtained using two types of renewable raw materials: bio-polyols and a cellulose filler (ARBOCEL® P 4000 X, JRS Rettenmaier, Rosenberg, Germany). A polyurethane system containing 40 wt.% of rapeseed oil-based polyols was modified with the cellulose filler in amounts of 1, 2, and 3 php (per hundred polyols). The cellulose was incorporated into the polyol premix as filler dispersion in a petrochemical polyol made using calenders. The cellulose filler was examined in terms of the degree of crystallinity using the powder X-ray diffraction PXRD -and the presence of bonds by means of the fourier transform infrared spectroscopy FT-IR. It was found that the addition of the cellulose filler increased the number of cells in the foams in both cross-sections—parallel and perpendicular to the direction of the foam growth—while reducing the sizes of those cells. Additionally, the foams had closed cell contents of more than 90% and initial thermal conductivity coefficients of 24.8 mW/m∙K. The insulation materials were dimensionally stable, especially at temperatures close to 0 °C, which qualifies them for use as insulation at low temperatures.

Study of the Activated Charcoal Structure from Water Hyacinth Based on Carbonization Temperature Variations and Activators

2021 ◽  
Vol 1028 ◽  
pp. 326-330
Author(s):  
Otong Nurhilal ◽  
Sahrul Hidayat ◽  
Dadan Sumiarsa ◽  
Maykel Manawan ◽  
Risdiana
Keyword(s):  
Carbon Material ◽  
Activated Charcoal ◽  
Water Hyacinth ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Lithium Sulfur Batteries ◽  
Amorphous Structures ◽  
Degree Of Graphitization ◽  
The Degree Of Crystallinity

The quality of the carbon material for application of electrodes in the battery is indicated by its ability to intercalate ions, atoms or molecules. Graphite is a carbon material with good intercalation capability. In this research, a carbon material in the form of activated charcoal produced from biomass of water hyacinth has been prepared, which is carbonized at various temperatures of 400, 500, and 600 °C with three different activators of ZnCl2, KOH and H3PO4. The activated charcoal will be used as a cathode composite in lithium sulfur batteries. To determine the quality of the activated charcoal, the structure properties of activated charcoal were characterized using X-ray diffraction (XRD). Several parameters that are determined from XRD data included the degree of crystallinity, and the degree of graphitization (Y). The degree of crystallinity was found in the ranges between 5.56 and 12.6%, where activated charcoal was dominated by amorphous structures. The value of the degree of graphitization was about 36%.

Effects of the Different Crystallization Time on Synthesis of Zeolite 4A from by-Products of Polysilicon Production Process

2011 ◽  
Vol 347-353 ◽  
pp. 246-251
Author(s):  
Xing Yong Liu ◽  
Min Li ◽  
Hong Chen ◽  
Wei Wei
Keyword(s):  
Production Process ◽  
Degree Of Crystallinity ◽  
Crystallization Time ◽  
Crystallinity Degree ◽  
Structure Morphology ◽  
Zeolite 4A ◽  
Single Structure ◽  
Ft Ir ◽  
The Degree Of Crystallinity ◽  
By Products

Pure form,single phase and high crystalline zeolite 4A samples were synthesized during hydrothermal treatment of by-products in polysilicon production process. The effects of the different crystallization time on the degree of crystallinity, skeleton structure, morphology, size of the particle and its distribution of zeolite 4A samples were investigated using XRD,FT-IR,SEM and Zetasizer. The results indicated that the zeolite 4A sample featured high crystallinity degree, excellent dispersivity, high purity and single structure.

scholarly journals Characterization of Serpentines from Different Regions by Transmission Electron Microscopy, X-ray Diffraction, BET Specific Surface Area and Vibrational and Electronic Spectroscopy

Fibers ◽  
2019 ◽  
Vol 7 (5) ◽  
pp. 47 ◽  
Author(s):  
Miguel A. Rivero Crespo ◽  
Dolores Pereira Gómez ◽  
María V. Villa García ◽  
José M. Gallardo Amores ◽  
Vicente Sánchez Escribano
Keyword(s):  
Electron Microscopy ◽  
Relative Intensity ◽  
Electronic Spectroscopy ◽  
Visible Region ◽  
Band Gap Energy ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Oh Groups ◽  
X Ray ◽  
Xrd Patterns

Serpentinite powdered samples from four different regions were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), SBET and porosity measurements, UV-Vis and Infrared Spectroscopy of the skeletal region and surface OH groups. SEM micrographs of the samples showed a prismatic morphology when the lizardite was the predominant phase, while if antigorite phase prevailed, the particles had a globular morphology. The few fibrous-shaped particles, only observed by SEM and weakly detected by XRD on MO-9C and MO13 samples, were characteristic of the chrysotile phase. All diffraction XRD patterns showed characteristic peaks of antigorite and lizardite serpentine phases, with crystallite sizes in the range 310–250 Å and with different degrees and types of carbonation processes, one derived from the transformation of the serpentine, generating dolomite, and another by direct precipitation of calcite. The SBET reached values between 38–24 m2∙g−1 for the samples less crystalline, in agreement with the XRD patterns, while those with a higher degree of crystallinity gave values close to 8–9 m2∙g−1. In the UV region all electronic spectra were dominated by the absorption edge due to O2− → Si4+ charge transfer transition, with Si4+ in tetrahedral coordination, corresponding to a band gap energy of ca 4.7 eV. In the visible region, 800–350 nm, the spectra of all samples, except Donai, presented at least two weak and broad absorptions centred in the range 650–800 and 550–360 nm, associated with the presence of Fe3+ ions from the oxidation of structural Fe2+ ions in the serpentinites ((MgxFe2+1−x)3Si2O5(OH)4). The relative intensity of the IR bands corresponding to the stretching modes of the OH’s groups indicated the prevalence of one of the two phases, antigorite or lizardite, in the serpentinites. We proposed that the different relative intensity of these bands could be considered as diagnostic to differentiate the predominance of these phases in serpentinites.

scholarly journals Hemp Fibre Reinforced Poly(Lactic Acid) Composites

2007 ◽  
Vol 29-30 ◽  
pp. 337-340 ◽  
Author(s):  
M.A. Sawpan ◽  
K.L. Pickering ◽  
Alan Fernyhough
Keyword(s):  
Lactic Acid ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Hemp Fibre ◽  
Reinforcing Material ◽  
Fibre Loading ◽  
The Degree Of Crystallinity

The potential of hemp fibre as a reinforcing material for Poly(lactic acid) (PLA) was investigated. Good interaction between hemp fibre and PLA resulted in increases of 100% for Young’s modulus and 30% for tensile strength of composites containing 30 wt% fibre. Different predictive ‘rule of mixtures’ models (e.g. Parallel, Series and Hirsch) were assessed regarding the dependence of tensile properties on fibre loading. Limited agreement with models was observed. Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) studies showed that hemp fibre increased the degree of crystallinity in PLA composites.

An Investigation on Structural and Optical Properties of Nanocrystalline Bismuth Ferrite and Manganese Sillenite Powders

2020 ◽  
Vol 835 ◽  
pp. 317-323
Author(s):  
D.A. Rayan ◽  
E.A. Abdel-Mawla ◽  
S.K. Mohamed ◽  
A.A. Mohamed ◽  
Mohamed M. Rashad
Keyword(s):  
Optical Properties ◽  
Bismuth Ferrite ◽  
Ammonium Hydroxide ◽  
Band Gap Energy ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Munk Function ◽  
Ft Ir ◽  
Uv Visible ◽  
Co Precipitation

Nanocrystalline bismuth ferrite BFO; BiFeO3 and manganese sillenite, BMO; Bi12MnO20 (BMO) powders have been successfully elaborated using a facile co-precipitation approach. The formed materials were examined using X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FE-SEM). Furthermore, the change in the optical properties was performed based on Fourier transform infrared spectroscopy (FT-IR) and UV-visible spectrophotometer. Typical, pure BiFeO3 and Bi12MnO20 phases were detected for the precursors precipitated at pH 10 based on ammonium hydroxide as a base then annealed at 500°C for 2h. Eventually, the optical band gap energy of BFO and BMO using Kubelka–Munk function based on Tauc’s plot was found to be 2.12 and 2.79 eV, respectively.

Study of the structure and thermal characteristics of nanocomposites based on polyvinyl alcohol and intercalated montmorillonite

2019 ◽  
pp. 089270571987919
Author(s):  
Volodymyr Krasinskyi ◽  
Ivan Gajdos ◽  
Oleh Suberlyak ◽  
Viktoria Antoniuk ◽  
Tomasz Jachowicz
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Acrylic Acid ◽  
Polyvinyl Alcohol ◽  
Thermal Characteristics ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
The Degree Of Crystallinity

The structure and thermal characteristics of nanocomposites based on polyvinyl alcohol (PVA) and montmorillonite (MMT) intercalated with polyvinylpyrrolidone were investigated by X-ray diffraction analysis and differential scanning calorimetry. The modification of PVA with intercalated MMT reduces the degree of crystallinity of the resulting nanocomposites but significantly increases their thermal stability. Under ultrasound, the intercalated MMT was completely distributed in a PVA solution and formed a monocrystalline structure. Films based on PVA with modified MMT were cross-linked at 110°C in the presence of 5 wt% acrylic acid and 0.5 wt% Ferrous(II) sulfate as an initiator. The formed films have a homogeneous cross-linked structure.

The Synthesis and Crystallization of Poly(vinylidene fluoride) in Supercritical CO2

e-Polymers ◽  
2006 ◽  
Vol 6 (1) ◽  
Author(s):  
Zhendong Shi ◽  
Zhen Zheng ◽  
Xiaoli Su ◽  
Xinling Wang
Keyword(s):  
Vinylidene Fluoride ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Molecular Weights ◽  
Good Solubility ◽  
Poly Vinylidene Fluoride ◽  
Ft Ir ◽  
Application Fields ◽  
Crystallization Mode

AbstractA series of poly(vinylidene fluoride)s (PVDFs) is synthesized in supercritical carbon dioxide (sc-CO2). The influences of polymerization pressure, molecular weight distribution and H-H defect concentration on the crystallization of PVDF have been studied in combination with differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXRD) and Fourier transform infrared spectroscopy (FT-IR) measurements. The result shows that the morphology, molecular weights, polydispersity and head-to-head (H-H) defect concentrations of the PVDFs are affected by the reaction pressure and good solubility generated from sc-CO2. Especially, the sc-CO2 polymerization has greatly improved the crystallization mode of the obtained PVDFs such as the complete degree of crystallinity, crystallinity and the crystal phase. This will create more comprehensive application fields for PVDF.

scholarly journals Development and Characterization of Novel Polyurethane Films Impregnated with Tolfenamic Acid for Therapeutic Applications

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Hilal Istanbullu ◽  
Sofia Ahmed ◽  
Muhammad Ali Sheraz ◽  
Ihtesham ur Rehman
Keyword(s):  
Polymer Concentration ◽  
Tolfenamic Acid ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Release Studies ◽  
Evaporation Technique ◽  
Crystallinity Changes ◽  
The Degree Of Crystallinity

The present study deals with the preparation of polyurethane (PU) films impregnated with a nonsteroidal anti-inflammatory drug, tolfenamic acid (TA). Solvent evaporation technique has been employed for the preparation of TA-PU films in two different ratios of 1 : 2 and 1 : 5 in Tetrahydrofuran (THF) or THF-ethanol mixtures. The prepared films were characterized using X-Ray Diffraction (XRD), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and release studies. The results indicate transformation of crystalline TA to its amorphous form. The degree of crystallinity changes both by increasing the polymer concentration and solvent used for the film preparations. The release profiles of TA were also found to be affected, showing a decrease from approximately 50% to 25% from 1 : 2 to 1 : 5 ratios, respectively.

Sign in / Sign up

Export Citation Format

Share Document