scholarly journals Study on the Production Mode of Horizontal Well from Water Huff and Puff to Segmented Injection and Production in Tight Reservoir

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Shiying Di ◽  
Shiqing Cheng ◽  
Cao Wei ◽  
Wenpeng Bai ◽  
Ruyuan Shang ◽  
...  
Keyword(s):  
Dynamic Fracture ◽  
Oil Recovery ◽  
Recovery Rate ◽  
Water Injection ◽  
Fracture Network ◽  
Natural Fracture ◽  
Natural Fractures ◽  
Tight Reservoir ◽  
Tight Reservoirs ◽  
Cumulative Recovery

Water huff and puff in horizontal wells in tight reservoirs has achieved good results in replenishing formation energy. However, after multiple rounds of treatment, a rapid decrease in formation pressure takes place making it difficult to maintain stable production. To improve the oil recovery rate of tight reservoirs, it is imminent to change the development mode. In this work, the stress distribution characteristics at fracture tips were analyzed based on Irwin theory and elastic theory. A model of propagation and closure length of fractures was established based on the propagation mechanism of water injection-induced natural fracture and the energy balance principle of fracture mechanics. Surfactant imbibition experiments were carried out according to the imbibition principle of surfactant system, and the propagation law of natural fractures was described with numerical simulation to analyze the seepage characteristics of dynamic fracture network. On the basis of the above works, alternating water huff and puff into segmented injection and production was proposed according to the distribution law of dynamic fracture network. The developing process of an actual well case by these two developing modes was simulated to predict 18 years of cumulative recovery, pressure distribution, and recovery rate. Results showed that when stress intensity factor exceeds the fracture toughness, the natural fractures will extend along their original directions and get connected, forming an irregular fracture network. The lengths of fractures after propagation and closure will not bring about water channeling for they are far shorter than well and interval spacing. Surfactant could diminish the resistance of boundary layer by reducing the wetting contact angle, ending up with an improvement in imbibition efficiency. Radial displacement and dynamic imbibition occur simultaneously in a dynamic fracture network during the early stage of water injection, while static imbibition mainly occurs during injection shutdown period and well soaking. According to comparison, the swept area of segmented injection and production was larger, ending up with a continuous increase of simulated recovery rate and cumulative recovery. The findings of this study show alternating water huff and puff after to segmented injection and production in fractured tight reservoir can allow full play of dynamic fracture network’s potential and achieve effective enhancement in oil recovery rate.

Method for calculating the fracture porosity of tight-fracture reservoirs

Geophysics ◽  
2016 ◽  
Vol 81 (4) ◽  
pp. IM57-IM70 ◽  
Author(s):  
Jingling Xu ◽  
Baoying Zhang ◽  
Yuxing Qin ◽  
Guangwei Cao ◽  
Hui Zhang
Keyword(s):  
Correlation Coefficient ◽  
Natural Fracture ◽  
Natural Fractures ◽  
Tight Sandstone ◽  
Fracture Porosity ◽  
Response Characteristics ◽  
Tight Reservoir ◽  
Tight Reservoirs ◽  
The Difference ◽  
Shale Reservoirs

Identifying fractures and evaluating the parameters of tight reservoirs are important problems. Developing methods to accurately interpret logging data for tight sandstone and shale reservoirs is of great significance, especially when only conventional logging data can be obtained. Identifying natural fractures with limited available data is challenging. Comparing and analyzing the log response characteristics of the natural fracture zone of a tight reservoir indicate that acoustic (AC) and density (DEN) data are highly sensitive to fractures in tight reservoirs. First, we have obtained the characteristics and differences of the log response of natural fractures. Second, we established a model that is based on these sensitive log-response characteristics (AC and DEN) to identify fractures (correlation coefficient method with window lengths), and we analyzed the cut-off of the correlation coefficient. Then, we established a model (the revised Wyllie difference method) to characterize the fracture porosity based on the difference in the sensitive log responses of the fracture (the difference in the AC and DEN curves). Finally, we applied this methodology to a case study of a tight reservoir in the Sichuan Basin, China, and the AC-DEN correlation coefficient and fracture porosity are calculated. The AC-DEN correlation coefficient adequately identifies fractures, and the calculated fracture porosity is consistent with the fracture porosity from full borehole microresistivity imaging. Thus, this method is applicable to evaluating fractures in tight-fracture reservoirs.

Coupled Flow/Geomechanics Modeling of Interfracture Water Injection To Enhance Oil Recovery in Tight Reservoirs

SPE Journal ◽  
2020 ◽  
Author(s):  
Yongzan Liu ◽  
Lijun Liu ◽  
Juliana Y. Leung ◽  
Kan Wu ◽  
George Moridis
Keyword(s):  
Oil Recovery ◽  
Horizontal Well ◽  
Water Injection ◽  
Injection Rate ◽  
Natural Fracture ◽  
Tight Oil ◽  
Coupled Flow ◽  
Fracture Spacing ◽  
Tight Reservoirs ◽  
Enhance Oil Recovery

Summary Unconventional tight reservoirs that are typically characterized by low permeability and low porosity have contributed significantly to the global hydrocarbon production in recent years. Although hydraulic fracturing, along with horizontal well drilling, enables the economic development of such reservoirs, the production rate often declines sharply and results in low primary hydrocarbon recovery. The application of enhanced-oil-recovery (EOR) techniques in tight reservoirs has received much interest. In this study, the feasibility and efficiency of interfracture water injection to enhance oil recovery in multistage fractured tight oil reservoirs are analyzed through an efficient coupled flow/geomechanics model with an embedded discrete-fracture model (EDFM). A combined finite-volume/finite-element scheme is used to discretize the governing equations for flow and geomechanics, and the coupled problem is solved sequentially using a fixed-stress splitting algorithm. A basic numerical model consisting of a 15-stage fractured horizontal well is constructed using the petrophysical and geomechanical properties of a tight oil formation in Ordos Basin, China. Fractures indexed with even numbers are switched into injecting fractures when the production rate has dropped to less than a certain threshold. The improvement of oil recovery is analyzed by comparing the production profiles with and without water injection. In this coupled model, the fracture closure/opening during production/injection is considered according to the constitutive relations between fracture aperture and effective normal stress acting on the fracture faces. The poromechanical response of matrix is modeled by the Biot (1941) theory. The effects of fracture spacing, injection rate, and the presence of a natural-fracture network on oil-recovery enhancement are discussed through sensitivity analysis. The main mechanisms of interfracture water injection for enhancing oil recovery are waterflooding and reservoir-pressure maintenance. Small fracture spacing tends to reduce the oil recovery because of fracture interference and a limited drainage area; therefore, the primary depletion stage is shortened as the fracture spacing is reduced. The influence of interfracture water injection is more pronounced with smaller fracture spacing because the pressure-transient responses near the producing fractures are more dramatic considering the close proximity between the injecting fracture and the producing fracture. Although a higher injection rate results in higher oil recovery, the injectivity in low-permeability reservoirs limits the maximum-allowable injection rate. When secondary (natural)-fracture networks are considered, neighboring hydraulic fractures can be connected to one another via the secondary fractures, particularly if the interfracture spacing is small. Water can break through in the producing fractures quickly, which could also lead to high water cut and suboptimal oil-recovery performance. This study tests the feasibility and efficiency of interfracture injection to enhance tight oil recovery. The results indicate that interfracture injection can be a promising EOR technique for tight oil reservoirs, which sheds lights on future completion strategies and production design in tight reservoirs.

scholarly journals Analysis of hydraulic fracture behavior and well pattern optimization in anisotropic coal reservoirs

2020 ◽  
pp. 014459872096083
Author(s):  
Yulong Liu ◽  
Dazhen Tang ◽  
Hao Xu ◽  
Wei Hou ◽  
Xia Yan
Keyword(s):  
Hydraulic Fracture ◽  
Coalbed Methane ◽  
Fracture Network ◽  
Simulation Software ◽  
Natural Fracture ◽  
Hydraulic Fractures ◽  
Natural Fractures ◽  
Well Pattern ◽  
Well Pattern Optimization ◽  
The Impact

Macrolithotypes control the pore-fracture distribution heterogeneity in coal, which impacts stimulation via hydrofracturing and coalbed methane (CBM) production in the reservoir. Here, the hydraulic fracture was evaluated using the microseismic signal behavior for each macrolithotype with microfracture imaging technology, and the impact of the macrolithotype on hydraulic fracture initiation and propagation was investigated systematically. The result showed that the propagation types of hydraulic fractures are controlled by the macrolithotype. Due to the well-developed natural fracture network, the fracture in the bright coal is more likely to form the “complex fracture network”, and the “simple” case often happens in the dull coal. The hydraulic fracture differences are likely to impact the permeability pathways and the well productivity appears to vary when developing different coal macrolithtypes. Thus, considering the difference of hydraulic fracture and permeability, the CBM productivity characteristics controlled by coal petrology were simulated by numerical simulation software, and the rationality of well pattern optimization factors for each coal macrolithotype was demonstrated. The results showed the square well pattern is more suitable for dull coal and semi-dull coal with undeveloped natural fractures, while diamond and rectangular well pattern is more suitable for semi-bright coal and bright coal with more developed natural fractures and more complex fracturing fracture network; the optimum wells spacing of bright coal and semi-bright coal is 300 m and 250 m, while that of semi-dull coal and dull coal is just 200 m.

scholarly journals Experimental Investigation on Oil Enhancement Mechanism of Hot Water Injection in tight reservoirs

Open Physics ◽  
2016 ◽  
Vol 14 (1) ◽  
pp. 703-713 ◽  
Author(s):  
Hao Yongmao ◽  
Lu Mingjing ◽  
Dong Chengshun ◽  
Jia Jianpeng ◽  
Su Yuliang ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Saturation ◽  
Water Injection ◽  
Hot Water ◽  
Water Flooding ◽  
Water Displacement ◽  
Pore Characteristics ◽  
Irreducible Water Saturation ◽  
Tight Reservoirs ◽  
Oil Water

AbstractAimed at enhancing the oil recovery of tight reservoirs, the mechanism of hot water flooding was studied in this paper. Experiments were conducted to investigate the influence of hot water injection on oil properties, and the interaction between rock and fluid, petrophysical property of the reservoirs. Results show that with the injected water temperature increasing, the oil/water viscosity ratio falls slightly in a tight reservoir which has little effect on oil recovery. Further it shows that the volume factor of oil increases significantly which can increase the formation energy and thus raise the formation pressure. At the same time, oil/water interfacial tension decreases slightly which has a positive effect on production though the reduction is not obvious. Meanwhile, the irreducible water saturation and the residual oil saturation are both reduced, the common percolation area of two phases is widened and the general shape of the curve improves. The threshold pressure gradient that crude oil starts to flow also decreases. It relates the power function to the temperature, which means it will be easier for oil production and water injection. Further the pore characteristics of reservoir rocks improves which leads to better water displacement. Based on the experimental results and influence of temperature on different aspects of hot water injection, the flow velocity expression of two-phase of oil and water after hot water injection in tight reservoirs is obtained.

scholarly journals Experimental Study on Enhanced Oil Recovery by Nitrogen-Water Alternative Injection in Reservoir with Natural Fractures

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiang Li ◽  
Yuan Cheng ◽  
Wulong Tao ◽  
Shalake Sarulicaoketi ◽  
Xuhui Ji ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Gas Injection ◽  
Water Injection ◽  
Injection Pressure ◽  
Injection Rate ◽  
Water Flooding ◽  
Orthogonal Experimental Design ◽  
Fractured Reservoir ◽  
Natural Fractures ◽  
Nitrogen Injection

The production of a low permeability reservoir decreases rapidly by depletion development, and it needs to supplement formation energy to obtain stable production. Common energy supplement methods include water injection and gas injection. Nitrogen injection is an economic and effective development method for specific reservoir types. In order to study the feasibility and reasonable injection parameters of nitrogen injection development of fractured reservoir, this paper uses long cores to carry out displacement experiment. Firstly, the effects of water injection and nitrogen injection development of a fractured reservoir are compared through experiments to demonstrate the feasibility of nitrogen injection development of the fractured reservoir. Secondly, the effects of gas-water alternate displacement after water drive and gas-water alternate displacement after gas drive are compared through experiments to study the situation of water injection or gas injection development. Finally, the reasonable parameters of nitrogen gas-water alternate injection are optimized by orthogonal experimental design. Results show that nitrogen injection can effectively enhance oil production of the reservoir with natural fractures in early periods, but gas channeling easily occurs in continuous nitrogen flooding. After water flooding, gas-water alternate flooding can effectively reduce the injection pressure and improve the reservoir recovery, but the time of gas-water alternate injection cannot be too late. It is revealed that the factors influencing the nitrogen-water alternative effect are sorted from large to small as follows: cycle injected volume, nitrogen and water slug ratio, and injection rate. The optimal cycle injected volume is around 1 PV, the nitrogen and water slug ratio is between 1 and 2, and the injection rate is between 0.1 and 0.2 mL/min.

A Mathematical Model for Natural Fracture Evolution in Water-Flooding Oil Reservoir

2013 ◽  
Vol 868 ◽  
pp. 535-541
Author(s):  
Hong Liu ◽  
Lin Wang ◽  
Yu Wu Zhou ◽  
Xi Nan Yu
Keyword(s):  
Oil Recovery ◽  
Rock Fracture ◽  
Fractured Reservoirs ◽  
Water Injection ◽  
Injection Pressure ◽  
Natural Fracture ◽  
Water Flooding ◽  
Oil Well ◽  
Fractured Reservoir ◽  
Naturally Fractured

The fractured low permeability reservoirs develop complex fracture network. As the of waterflooding recovery heightens, excessive high injection pressures and excessive water injection rate will result in open, initiation, propagation and coalescence of micro-fracture, connecting injection with production form the high permeability zone, which results in a one-way onrush of waterflooding, water cut in oil well water rise quickly, causing a severe oil well flooding and channeling, thereby reducing the ultimate oil recovery efficiency. The effect of the waterflooding seepage within natural fracture on fracture initiation is studied and analyzed here, applying the theory of rock fracture mechanics to analyze the interaction of fracture system for naturally fractured reservoirs in waterflooding developing process, studying the mechanical mechanism of opening, initiation, propagation and coalescence of natural fracture under injection pressure, which is important theoretical significance for studying the distribution law of fracture and defining appreciate water injection mode and injection pressure in the process of injection development of the naturally fractured reservoir and for delaying the directivity water break-through and water flooding rate of oil well in the process of injection development.

scholarly journals Numerical Simulation of Hydraulic Fracture Propagation in Coal Seams with Discontinuous Natural Fracture Networks

Processes ◽  
2018 ◽  
Vol 6 (8) ◽  
pp. 113 ◽  
Author(s):  
Shen Wang ◽  
Huamin Li ◽  
Dongyin Li
Keyword(s):  
Hydraulic Fracture ◽  
Fracture Propagation ◽  
Fracture Network ◽  
Natural Fracture ◽  
Cohesive Element ◽  
Natural Fractures ◽  
Fracture Networks ◽  
Coal Seams ◽  
Hydraulic Fracture Network ◽  
Hydraulic Fracture Propagation

To investigate the mechanism of hydraulic fracture propagation in coal seams with discontinuous natural fractures, an innovative finite element meshing scheme for modeling hydraulic fracturing was proposed. Hydraulic fracture propagation and interaction with discontinuous natural fracture networks in coal seams were modeled based on the cohesive element method. The hydraulic fracture network characteristics, the growth process of the secondary hydraulic fractures, the pore pressure distribution and the variation of bottomhole pressure were analyzed. The improved cohesive element method, which considers the leak-off and seepage behaviors of fracturing liquid, is capable of modeling hydraulic fracturing in naturally fractured formations. The results indicate that under high stress difference conditions, the hydraulic fracture network is spindle-shaped, and shows a multi-level branch structure. The ratio of secondary fracture total length to main fracture total length was 2.11~3.62, suggesting that the secondary fractures are an important part of the hydraulic fracture network in coal seams. In deep coal seams, the break pressure of discontinuous natural fractures mainly depends on the in-situ stress field and the direction of natural fractures. The mechanism of hydraulic fracture propagation in deep coal seams is significantly different from that in hard and tight rock layers.

Predicting Well Performance in Naturally Fractured Reservoir

2013 ◽  
Author(s):  
Yunsuk Hwang ◽  
Jiajing Lin ◽  
David Schechter ◽  
Ding Zhu
Keyword(s):  
Hydraulic Fracture ◽  
Fracture Network ◽  
Darcy Flow ◽  
Natural Fracture ◽  
Hydraulic Fractures ◽  
Natural Fractures ◽  
Well Performance ◽  
Fracture Networks ◽  
Complex Fracture ◽  
Complex Fracture Network

Multiple hydraulic fracture treatments in reservoirs with natural fractures create complex fracture networks. Predicting well performance in such a complex fracture network system is an extreme challenge. The statistical nature of natural fracture networks changes the flow characteristics from that of a single linear fracture. Simply using single linear fracture models for individual fractures, and then summing the flow from each fracture as the total flow rate for the network could introduce significant error. In this paper we present a semi-analytical model by a source method to estimate well performance in a complex fracture network system. The method simulates complex fracture systems in a more reasonable approach. The natural fracture system we used is fractal discrete fracture network model. We then added multiple dominating hydraulic fractures to the natural fracture system. Each of the hydraulic fractures is connected to the horizontal wellbore, and some of the natural fractures are connected to the hydraulic fractures through the network description. Each fracture, natural or hydraulically induced, is treated as a series of slab sources. The analytical solution of superposed slab sources provides the base of the approach, and the overall flow from each fracture and the effect between the fractures are modeled by applying the superposition principle to all of the fractures. The fluid inside the natural fractures flows into the hydraulic fractures, and the fluid of the hydraulic fracture from both the reservoir and the natural fractures flows to the wellbore. This paper also shows that non-Darcy flow effects have an impact on the performance of fractured horizontal wells. In hydraulic fracture calculation, non-Darcy flow can be treated as the reduction of permeability in the fracture to a considerably smaller effective permeability. The reduction is about 2% to 20%, due to non-Darcy flow that can result in a low rate. The semi-analytical solution presented can be used to efficiently calculate the flow rate of multistage-fractured wells. Examples are used to illustrate the application of the model to evaluate well performance in reservoirs that contain complex fracture networks.

Sign in / Sign up

Export Citation Format

Share Document