scholarly journals Micromechanical Properties of Steel-Fiber-Reinforced Cementitious Composites Characterized with Nanoindentation

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Yan-Ru Zhao ◽  
Lei Wang ◽  
Yan-Ying Dong
Keyword(s):  
Silica Fume ◽  
Steel Fiber ◽  
Cement Matrix ◽  
Indentation Hardness ◽  
Input Energy ◽  
Micromechanical Properties ◽  
Total Input ◽  
Binder Ratio ◽  
Fiber Reinforced Cementitious Composites ◽  
Water Binder Ratio

The micromechanical properties of the steel-fiber-reinforced cementitious composites with different water-binder ratios and silica fume contents were studied by nanoindentation. The elastic modulus, indentation hardness, total input energy, and ratio of the elastic deformation energy to the total input energy were analyzed in the interfacial transition zone (ITZ) and the cement matrix. The results show that with the reduction of water-binder ratio in the range of 0.18–0.24, the elastic modulus, indentation hardness, elastic deformation capacity, and energy dissipation capacity increased in the ITZ and cement matrix, and the increase of the ITZ was greater than that of the matrix, yet the ITZ did not disappear. With the increase of silica fume content in the range of 0–30%, the weak ITZ was gradually strengthened or even disappeared. In terms of obtaining the stronger ITZ, adding silica fume is more effective than reducing the water-binder ratio. When the water-binder ratio was high at 0.24, large silica fume contents (30%) had significant effects on enhancing the micromechanical properties of the ITZ and matrix. At a low water-binder ratio of 0.18, large silica fume contents (30%) enhanced the micromechanical properties of the ITZ while degrading those of the cement matrix.

Cropped Steel Fiber Reinforced Chemically Bonded Ceramic (CBC) Composites

1987 ◽  
Vol 114 ◽  
Author(s):  
Sean Wise ◽  
Kevan Jones ◽  
Claudio Herzfeld ◽  
David D. Double
Keyword(s):  
Silica Fume ◽  
Steel Fiber ◽  
High Strength ◽  
Cement Matrix ◽  
Metal Fiber ◽  
Morphological Form ◽  
The Matrix ◽  
Compressive And Flexural Strengths ◽  
Equivalent Properties ◽  
Very High

ABSTRACTVery high strength castable chemically bonded ceramic (CBC) materials have been prepared which consist of finely chopped steel fibers and steel aggregate in a silica modified portland cement matrix. This paper examines the effect of metal fiber addition on compressive and flexural strengths. The overall chemistry of the matrix is held constant but the morphological form of silica used and the cure conditions are altered to examine their effect. Compressive strengths in excess of 500 MPa and flexural strengths in excess of 80 MPa can be obtained.It is found that flexural strength increases proportionally with fiber content over the range of 0 to 10% by volume. Compressive strengths are not affected. Use of silica fume in the mixes produces higher strengths at low temperatures than mixes which contain only crystalline silica. High temperature curing/drying (400°C), which produces the highest strengths, produces equivalent properties for formulations with and without silica fume. Higher water/cement ratios are found to reduce compressive strengths but have relatively little effect on the flexural properties.

Effect of Heat Treatment on Properties of Portland Cement Pastes: Determination through Ultra-Microhardness Test

2015 ◽  
Vol 820 ◽  
pp. 492-496
Author(s):  
D.C.S. Garcia ◽  
Roberto Braga Figueiredo ◽  
Maria Teresa Paulino Aguilar
Keyword(s):  
Heat Treatment ◽  
Portland Cement ◽  
Optical Microscopy ◽  
Silica Fume ◽  
Ordinary Portland Cement ◽  
Cement Pastes ◽  
Microhardness Test ◽  
Material Hardness ◽  
Binder Ratio ◽  
Water Binder Ratio

The aim of this paper was to investigate the influence of heat treatment on hardness evolution of cement pastes containing silica fume. The specimens were prepared with Ordinary Portland Cement, water/binder ratio of 0,40 and 25% wt. silica fume. The specimens were cast at room temperatures and after 24 hours, they were placed in a furnace for 24 hours, with heat regimes of 100°C, 200°C and 300°C and then submitted to the ultra-microhardness test. The microstructure was analyzed using optical microscopy. The results showed that the silica fume prevents the production of calcium hydroxide and the heat treatment increases the material hardness.

scholarly journals INFLUENCE OF SILICA COLLOID ON RHEOLOGY OF CEMENT PASTE WITH SUPERPLASTICIZER

2017 ◽  
Vol 25 (1) ◽  
pp. 73-80
Author(s):  
T.H. Chuong ◽  
P.V. Nga
Keyword(s):  
Experimental Data ◽  
Rheological Property ◽  
Silica Fume ◽  
Cement Paste ◽  
Rheological Behavior ◽  
Concrete Mixture ◽  
Silica Colloid ◽  
Binder Ratio ◽  
High Silica ◽  
Water Binder Ratio

Information of rheological behavior of binder paste is important for proportioning high slump concrete mixture at low water to cement ratios. This paper presents experimental data on the rheological property of silica colloid incorporated binder paste using naphthalene based and polycarboxylate based superplasticizer, compared to that of silica fume incorporated binder paste. Experimental data showed that silica colloid incorporated binder is compatible to tested superplasticizers in the all investigated range of silica colloid content, whereas the pastes incorporated with high silica fume content (over 10%) indicated incompatibility, especially to naphthalene based superplasticizer. There was also found out saturated content of superplasticizer corresponding to every kind of binder and water-binder ratio, with and without set retarding admixture. 

scholarly journals Use of condensed silica fume for making high-strength, self-consolidating concrete

2000 ◽  
Vol 27 (4) ◽  
pp. 620-627 ◽  
Author(s):  
A KH Kwan
Keyword(s):  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Self Consolidating Concrete ◽  
Concrete Mix ◽  
Binder Ratio ◽  
Condensed Silica Fume ◽  
Water Binder Ratio

A high concrete strength can be achieved by lowering the water/binder ratio and a high workability by adding a higher dosage of superplasticizer. However, a high-performance concrete with both high strength and high workability cannot be produced by just these means because lowering the water/binder ratio leads to lower workability and there is a limit to the increase in workability that can be attained by adding superplasticizer. To produce a high-strength, high-workability concrete, the concrete strength needs to be increased without lowering the water/binder ratio. This can be done by adding condensed silica fume. In this study, a series of trial mixing aimed at developing high-strength, self-consolidating concrete (mean cube strength >80 MPa and needs no compaction for consolidation) was carried out. Several mixes suitable for making such high-performance concrete have been developed and it was found that the addition of condensed silica fume may, under favourable conditions, increase not only the strength but also the workability of the concrete mix. Based on the trial mix results, charts for the design of high-strength, high-workability concrete mixes made of the studied constituents are presented.Key words: condensed silica fume, high-strength concrete, self-consolidating concrete.

Study on the Effect of Fly Ash or Silica Fume to Hydration Heat of Cement

2011 ◽  
Vol 250-253 ◽  
pp. 4001-4004 ◽  
Author(s):  
Li Guo Ma ◽  
Yun Sheng Zhang
Keyword(s):  
Fly Ash ◽  
Binary System ◽  
Silica Fume ◽  
Cement Paste ◽  
Heat Evolution ◽  
Hydration Heat ◽  
Dormant Period ◽  
Binder Ratio ◽  
Isothermal Calorimeter ◽  
Water Binder Ratio

The hydration heat evolution process is studied on the pure cement paste, the cement- fly ash binary system and the cement- silica fume binary system with water binder ratio(w/b) of 0.53, 0.35 and 0.23 by using isothermal calorimeter(TAM Air). The fly ash replacement in the cement-fly ash binary system is 10%, 30% and 50% respectively. The silica fume replacement in cement-silica fume binary system is 4%, 8% and 12% respectively. The experiments results indicate that w/b had great impact on the hydration heat evolution and the hydration heat decrease with the decrease in w/b. The addition of fly ash greatly decrease the exothermic rate and total hydration heat. The addition of silica fume shortens dormant period and increases the peak exothermic rate, but reduces the total hydration heat.

scholarly journals Effect of Silica Fume on the Rheological Properties of Cement Paste with Ultra-Low Water Binder Ratio

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 554
Author(s):  
Juan He ◽  
Congmi Cheng ◽  
Xiaofen Zhu ◽  
Xiaosen Li
Keyword(s):  
Hysteresis Loop ◽  
Rheological Properties ◽  
Yield Stress ◽  
Silica Fume ◽  
Plastic Viscosity ◽  
Rheological Parameters ◽  
Loop Area ◽  
Binder Ratio ◽  
Hysteresis Loop Area ◽  
Water Binder Ratio

The effect of silica fume on the rheological properties of a cement–silica fume–high range water reducer–water mixture with ultra-low water binder ratio (CSHWM) was studied. The results indicate that the W/B ratio and silica fume content have different effects on the rheological parameters, including the yield stress, plastic viscosity, and hysteresis loop area. The shear-thickening influence of CSHWM decreased with the increased silica fume content. When the silica fume content increased from 0% to 35%, the mixture with W/B ratio of 0.19 and 0.23 changed from a dilatant fluid to a Newtonian fluid, and then to a pseudoplastic fluid. When the silica fume content was less than 15%, the yield stress was close to 0. With the increase of silica fume content, the yield stress increased rapidly. The plastic viscosity and hysteresis loop area decreased slightly with the addition of a small amount of silica fume, but increased significantly with the continuous increase of silica fume. Compared with the Bingham and modified Bingham models, the Herschel–Buckley model is more applicable for this CSHWM.

scholarly journals Effect of the water/binder ratio on the hydration process of Portland cement pastes with silica fume and metakaolin

2022 ◽  
Vol 15 (1) ◽  
Author(s):  
Mara Monaliza Linhares Pereira ◽  
Ana Luiza Rocha de Souza ◽  
Valdirene Maria Silva Capuzzo ◽  
Rodrigo de Melo Lameiras
Keyword(s):  
Portland Cement ◽  
Silica Fume ◽  
Cementitious Materials ◽  
Hydration Process ◽  
X Ray Diffraction ◽  
Cement Pastes ◽  
X Ray ◽  
Binder Ratio ◽  
Water Binder Ratio ◽  
Mineralogical Phases

abstract: The microstructure of cement pastes is important to understand the effect of some parameters in the hydration process. In this context, this study had as objective to evaluate the effect of different water/binder (w/b) ratios in the hydration process of cementitious pastes produced with and without incorporation of silica fume and metakaolin. The pastes were obtained with water/binder ratios of 0.3, 0.4 e 0.5, with replacement, by weight, of Portland cement for silica fume and metakaolin, in the contents of 10% and 20%, respectively. It was performed the X-ray diffraction test of the pastes in the ages of 1, 3, 7, and 28 days, to evaluate the hydration evolution of the cementitious materials. According to the results obtained, it was observed that the cementitious pastes presented similar mineralogical phases, except for the pastes containing metakaolin due to the formation of new aluminate phases. With the increase of the water/binder ratio, the pozzolanic reactions and hydration occurred in greater proportion, standing out the metakaolin with greater reactivity.

Sign in / Sign up

Export Citation Format

Share Document