scholarly journals Behavior of Elastic Therapeutic Tapes under Dynamic and Static Conditions

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Hermela Ejegu ◽  
Bipin Kumar ◽  
Priyanka Gupta
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Internal Stress ◽  
Dynamic Condition ◽  
Physical And Mechanical Properties ◽  
Static Condition ◽  
Strain Rates ◽  
Lower Strain Rate ◽  
Lower Strain ◽  
Static Conditions

The aim of this paper is to determine the relaxation behavior of the therapeutic tape under different thermomechanical conditions over different time spans and to analyze the physical and mechanical properties of selected kinesiology tapes. The relaxation test was conducted under a static condition with two extended levels (25% and 50%) for one hour and a dynamic condition for 300 cycles with different loading-unloading values, strain rates, and temperatures. For both static and dynamic conditions, at a lower strain rate and higher load and temperature, the therapeutic tapes showed higher loss of internal stress and faster losses of efficiency. Under all selected conditions, the tape’s stress has decreased rapidly.

Influence of Mg Content, Grain Size and Strain Rate on Mechanical Properties and DSA Behavior of Al-Mg Alloys Processed by ECAP and Annealing

2014 ◽  
Vol 794-796 ◽  
pp. 870-875 ◽  
Author(s):  
Min Zha ◽  
Yan Jun Li ◽  
Ragnvald H. Mathiesen ◽  
Christine Baumgart ◽  
Hans J. Roven
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Strain Rate ◽  
Room Temperature ◽  
Uniform Elongation ◽  
Mg Alloys ◽  
Lower Strain Rate ◽  
Lower Strain ◽  
Mg Content ◽  
Al Mg Alloys

Ultrafine-grained (UFG) binary Al-xMg (x=1, 5 and 7 wt %) alloys were processed by equal channel angular pressing (ECAP) at room temperature via route Bccombined with inter-pass annealing. The effects of Mg content, grain size and strain rate on mechanical properties and dynamic strain aging (DSA) behaviour of the Al-Mg alloys upon tensile testing at room temperature were studied. An increase in Mg content from 5 to 7 wt % leads to a pronounced increase in strength and uniform elongation in both the as-homogenized and as-ECAP Al-Mg alloys. Thereby, the Al-7Mg alloy, either prior to or after ECAP processing, possess significantly higher strength and comparable or even higher uniform elongation than the more dilute Al-Mg alloys. However, the as-ECAP Al-Mg alloys exhibit significantly higher strength but little work hardening and hence rather limited uniform elongation. In general, decreasing grain size leads to significant increase in strength while dramatic decrease in ductility. Moreover, DSA serration amplitudes increase with reducing grain size in the micrometer range. However, the UFG Al-Mg alloys exhibit much less DSA effect than the micrometer scaled grain size counterparts, i.e. probably due to the high dislocation densities and special grain boundary features in the UFG materials. Also, the Al-Mg alloys, especially those with a UFG structure, exhibit higher strength and ductility at lower strain rate than at higher strain rate, due mainly to enhanced DSA effect and hence work hardening at a lower strain rate.

scholarly journals Mechanical properties and constitutive model of Sn-58Bi alloy

2021 ◽  
Author(s):  
Kebin Zhang ◽  
Wenbin Li ◽  
Ping Song ◽  
Changfang Zhao ◽  
Kewin Zhang
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Constitutive Model ◽  
Strain Rate ◽  
Compressive Stress ◽  
Split Hopkinson Pressure Bar ◽  
Testing Machine ◽  
Strain Rates ◽  
Stress Strain ◽  
Static Conditions

Abstract Sn-58Bi alloy is a strain-rate-sensitive material. To study the mechanical properties of Sn-58Bi alloy, an MTS universal testing machine and split-Hopkinson pressure bar were used to conduct quasi-static and dynamic testing on Sn-58Bi alloy, obtaining the stress-strain curve of Sn-58Bi alloy at the strain rate of 0.001–6316 s−1. By comparing the tensile and compressive stress–strain curves of Sn-58Bi alloy under quasi-static conditions, it is found that Sn-58Bi alloy is brittle, with its tensile yield strength lower than its compressive yield strength. By comparing the compressive stress–strain curves of Sn-58Bi alloy at different strain rates, it is found that the yield strength of Sn-58Bi alloy increases with increasing strain rate, and a strain-hardening phenomenon is manifested at high strain rate. By revising the Johnson–Cook constitutive model, the constitutive model of Sn-58Bi alloy at different strain rates was established, with the calculated results of the model in good agreement with the experimental results.

scholarly journals Hot Workability of 300M Steel Investigated by In Situ and Ex Situ Compression Tests

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 880 ◽  
Author(s):  
Rongchuang Chen ◽  
Haifeng Xiao ◽  
Min Wang ◽  
Jianjun Li
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Working ◽  
Ex Situ ◽  
Lower Strain Rate ◽  
Hot Workability ◽  
Compression Tests ◽  
300M Steel ◽  
Lower Strain

In this work, hot compression experiments of 300M steel were performed at 900–1150 °C and 0.01–10 s−1. The relation of flow stress and microstructure evolution was analyzed. The intriguing finding was that at a lower strain rate (0.01 s−1), the flow stress curves were single-peaked, while at a higher strain rate (10 s−1), no peak occurred. Metallographic observation results revealed the phenomenon was because dynamic recrystallization was more complete at a lower strain rate. In situ compression tests were carried out to compare with the results by ex situ compression tests. Hot working maps representing the influences of strains, strain rates, and temperatures were established. It was found that the power dissipation coefficient was not only related to the recrystallized grain size but was also related to the volume fraction of recrystallized grains. The optimal hot working parameters were suggested. This work provides comprehensive understanding of the hot workability of 300M steel in thermal compression.

scholarly journals A Review on Mechanical Properties of Natural Fibre Reinforced Polymer Composites under Various Strain Rates

2021 ◽  
Vol 5 (5) ◽  
pp. 130
Author(s):  
Tan Ke Khieng ◽  
Sujan Debnath ◽  
Ernest Ting Chaw Liang ◽  
Mahmood Anwar ◽  
Alokesh Pramanik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Polymer Composites ◽  
Stress Transfer ◽  
Natural Fibre ◽  
Transfer Efficiency ◽  
Strain Rates ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Fibre Matrix

With the lightning speed of technological evolution, the demand for high performance yet sustainable natural fibres reinforced polymer composites (NFPCs) are rising. Especially a mechanically competent NFPCs under various loading conditions are growing day by day. However, the polymers mechanical properties are strain-rate dependent due to their viscoelastic nature. Especially for natural fibre reinforced polymer composites (NFPCs) which the involvement of filler has caused rather complex failure mechanisms under different strain rates. Moreover, some uneven micro-sized natural fibres such as bagasse, coir and wood were found often resulting in micro-cracks and voids formation in composites. This paper provides an overview of recent research on the mechanical properties of NFPCs under various loading conditions-different form (tensile, compression, bending) and different strain rates. The literature on characterisation techniques toward different strain rates, composite failure behaviours and current challenges are summarised which have led to the notion of future study trend. The strength of NFPCs is generally found grow proportionally with the strain rate up to a certain degree depending on the fibre-matrix stress-transfer efficiency. The failure modes such as embrittlement and fibre-matrix debonding were often encountered at higher strain rates. The natural filler properties, amount, sizes and polymer matrix types are found to be few key factors affecting the performances of composites under various strain rates whereby optimally adjust these factors could maximise the fibre-matrix stress-transfer efficiency and led to performance increases under various loading strain rates.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

scholarly journals Strain-Rate and Grain‒Size Effects in Ice

1987 ◽  
Vol 33 (115) ◽  
pp. 274-280 ◽  
Author(s):  
David M. Cole
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Transition Point ◽  
Boundary Migration ◽  
Peak Stress ◽  
Strain Rates ◽  
Thin Sections ◽  
Fine Grained ◽  
Lower Strain ◽  
Polycrystalline Ice

AbstractThis paper presents and discusses the results of constant deformation-rate tests on laboratory-prepared polycrystalline ice. Strain-rates ranged from 10−7to 10−1s−1, grain–size ranged from 1.5 to 5.8 mm, and the test temperature was −5°C.At strain-rates between 10−7and 10−3s−1, the stress-strain-rate relationship followed a power law with an exponent ofn= 4.3 calculated without regard to grain-size. However, a reversal in the grain-size effect was observed: below a transition point near 4 × 10−6s−1the peak stress increased with increasing grain-size, while above the transition point the peak stress decreased with increasing grain-size. This latter trend persisted to the highest strain-rates observed. At strain-rates above 10−3s−1the peak stress became independent of strain-rate.The unusual trends exhibited at the lower strain-rates are attributed to the influence of the grain-size on the balance of the operative deformation mechanisms. Dynamic recrystallization appears to intervene in the case of the finer-grained material and serves to lower the peak stress. At comparable strain-rates, however, the large-grained material still experiences internal micro-fracturing, and thin sections reveal extensive deformation in the grain-boundary regions that is quite unlike the appearance of the strain-induced boundary migration characteristic of the fine-grained material.

scholarly journals New Approach In The Properties Evaluation Of Ultrafine-Grained OFHC Copper

2015 ◽  
Vol 60 (2) ◽  
pp. 605-614 ◽  
Author(s):  
T. Kvačkaj ◽  
A. Kováčová ◽  
J. Bidulská ◽  
R. Bidulský ◽  
R. Kočičko
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Tensile Tests ◽  
Coarse Grained ◽  
Wear Behaviour ◽  
Ofhc Copper ◽  
Strain Rates ◽  
Ultrafine Grained ◽  
Reduction Of Area ◽  
Pin On Disk

AbstractIn this study, static, dynamic and tribological properties of ultrafine-grained (UFG) oxygen-free high thermal conductivity (OFHC) copper were investigated in detail. In order to evaluate the mechanical behaviour at different strain rates, OFHC copper was tested using two devices resulting in static and dynamic regimes. Moreover, the copper was subjected to two different processing methods, which made possible to study the influence of structure. The study of strain rate and microstructure was focused on progress in the mechanical properties after tensile tests. It was found that the strain rate is an important parameter affecting mechanical properties of copper. The ultimate tensile strength increased with the strain rate increasing and this effect was more visible at high strain rates$({\dot \varepsilon} \sim 10^2 \;{\rm{s}}^{ - 1} )$. However, the reduction of area had a different progress depending on microstructural features of materials (coarse-grained vs. ultrafine-grained structure) and introduced strain rate conditions during plastic deformation (static vs. dynamic regime). The wear behaviour of copper was investigated through pin-on-disk tests. The wear tracks examination showed that the delamination and the mild oxidational wears are the main wear mechanisms.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

scholarly journals Mechanical properties of wrought magnesium alloys

2021 ◽  
Author(s):  
Sanjida Begum
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Magnesium Alloys ◽  
Bauschinger Effect ◽  
Fatigue Crack Initiation ◽  
Hysteresis Loops ◽  
Cyclic Hardening ◽  
Strain Ratio ◽  
Strain Hardening Exponent ◽  
Lower Strain

Lightweight magnesium alloys are being increasingly used in automotive and other transportation industries to achieve energy efficiency. The objective of this thesis was to study the mechanical properties of two wrought alloys AZ31 and AM30. With increasing strain rate the yield strength and ultimate tensile strength increased and the strain hardening exponent decreased for AM30 and increased for AZ31. Both alloys exhibited stable cyclic characteristics at lower strain amplitudes and cyclic hardening characteristics at higher strain amplitudes. The Bauschinger effect was pronounced at higher strain amplitudes, resulting in asymmetric hysteresis loops in both alloys. The influence of strain ratio (Rs), strain rate, and initial straining direction on the cyclic deformation characteristics and fatigue life was evaluated. At low Rs, both alloys exhibited strong cyclic hardening, which decreased as Rs increased. Fatigue crack initiation was observed to occur from the specimen surface and crack propagation was basically characterized by striation-like features.

Sign in / Sign up

Export Citation Format

Share Document