scholarly journals Numerical Simulation Research on Radial Force of Centrifugal Pump with Guide Vanes

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dongrong Meng ◽  
Ting Jiang ◽  
Hongling Deng ◽  
Gaoyang Hou
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Guide Vane ◽  
Radial Force ◽  
Flow State ◽  
Simulation Research ◽  
Flow Rates ◽  
Guide Vanes ◽  
Vector Distribution ◽  
Unsteady Numerical Simulation

To reveal the internal unsteady flow state of the guide vane centrifugal pump, in this paper, the standard SST k‐ω turbulent flow model is used for unsteady numerical simulation of the centrifugal pump. The characteristics of the flow field inside the centrifugal pump are analyzed, the resultant force and vector distribution of the radial force of the guide vane and impeller of the centrifugal pump under different flow rates are obtained, which were verified by experiments. The results show that the main reason of radial force of the impeller is the pressure asymmetry in each flow passage. The radial force will show periodic fluctuations due to the rotor-stator interference between the impeller and the guide vanes under different flow rates. The radial force on the impeller decreases gradually with the increase of the flow, the distribution is hexagonal or hexagonal shape, and the number of impeller blades is the same. The results can provide reference for the design of impeller and guide vane of centrifugal pump.

Analysis of unsteady radial forces of multistage centrifugal pump with double volute

2018 ◽  
Vol 35 (3) ◽  
pp. 1500-1511 ◽  
Author(s):  
Baoling Cui ◽  
Xiaodi Li ◽  
Kun Rao ◽  
Xiaoqi Jia ◽  
Xiaolin Nie
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Static Pressure ◽  
Radial Force ◽  
Radial Vibration ◽  
Flow Rates ◽  
Content Type ◽  
Blade Passing Frequency ◽  
Multistage Centrifugal Pump ◽  
Radial Forces

Purpose Radial vibration of horizontal centrifugal pump has a close association with radial exciting forces. The purpose of this paper is to analyze the unsteady radial force in multistage centrifugal pump with double volute in detail and investigate the relevance of static pressure, radial force and radial vibration. Design/methodology/approach The unsteady numerical simulation with realizable k-ε turbulence model was carried out for a multistage centrifugal pump with double volute using computational fluid dynamics codes Fluent. The performance tests were conducted by use of a closed loop system and performance curves from numerical simulation agree with that of experiment. Vibration tests were carried out by vibration probes instrumented on the bearing cover of pump near no-driven end. Fast Fourier transform was used to obtain the frequency components of radial forces on the impellers from numerical simulation, which are compared with ones of radial vibration from experiment in Y and Z direction. And the static pressure distributions in the impeller were analyzed under different flow rates. Findings The symmetrical double volute can effectively balance radial forces. The maximum radial force and vibration velocity appear at 0.6 Q among the three flow rates 0.6 Q, Q and 1.2 Q. The frequencies corresponding to relatively large amplitude of vibration velocities and radial forces on the impellers in Y direction are blade passing frequency of the impellers. Blade passing frequency of first-stage impeller and shaft frequency are predominating in Z direction. It indicates that the radial vibration of centrifugal pump is closely related to the unsteady radial force. Originality/value The unsteady radial forces of the impeller in multistage centrifugal pump with double volute were comprehensively analyzed. The radial forces should be considered to balance during the design of multistage centrifugal pump.

Hydraulic Characteristics of the New Type Bulb Turbine With Micro-Head

2013 ◽  
Author(s):  
Lingyu Li ◽  
Yuan Zheng ◽  
Daqing Zhou ◽  
Zihao Mi
Keyword(s):  
Numerical Simulation ◽  
Cfd Simulation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Flow Distribution ◽  
Three Dimensions ◽  
Guide Vanes ◽  
Runner Blade ◽  
Cfd Method ◽  
Bulb Turbine

The head of low-head hydropower stations is generally higher than 2.5m in the world, while micro-head hydropower resources which head is less than 2.5m are also very rich. In the paper, three-dimensional CFD method has been used to simulate flow passage of the micro-head bulb turbine. The design head and unit flow of the turbine was 1m and 3m3/s respectively. With the numerical simulation, the bulb turbine is researched by analyzing external characteristics of the bulb turbine, flow distribution before the runner, pressure distribution of the runner blade surface, and flow distribution of the outlet conduit under three different schemes. The turbine in second scheme was test by manufactured into a physical model. According to the results of numerical simulation and model test, bulb turbine with no guide vane in second scheme has simpler structure, lower cost, and better flow capacity than first scheme, which has traditional multi-guide vanes. Meanwhile, efficiency of second scheme has just little decrease. The results of three dimensions CFD simulation and test results agree well in second scheme, and higher efficiency is up to 77% which has a wider area with the head of 1m. The curved supports in third scheme are combined guide vanes to the fixed supports based on 2nd scheme. By the water circulations flowing along the curved supports which improve energy transformation ability of the runner, the efficiency of the turbine in third scheme is up to 82.6%. Third scheme, which has simpler structure and best performance, is appropriate for the development and utilization of micro-head hydropower resources in plains and oceans.

Numerical Research of the Effect of the Outlet Diameter of Diffuser on the Performance and the Radial Force in a Single-Stage Centrifugal Pump

2014 ◽  
Author(s):  
Jiang Wei ◽  
Li Guojun ◽  
Liu Pengfei ◽  
Zhang Lisheng ◽  
Qing Hongyang
Keyword(s):  
Centrifugal Pump ◽  
Radial Force ◽  
Numerical Results ◽  
Operating Conditions ◽  
Single Stage ◽  
Navier Stokes ◽  
Computational Domain ◽  
Ansys Fluent ◽  
Vaned Diffuser ◽  
Unsteady Numerical Simulation

In this paper, a single-stage pump with diffuser vanes of different outlet diameters has been investigated both numerically and experimentally. The influence of the diffuser vane outlet diameter on pump hydraulic performance and on the radial force of the impeller is explored. Pumps equipped with three different diffusers but with impellers and volutes of the same parameters were simulated by 3D Navier-Stokes solver ANSYS-FLUENT in order to study the effect of the outlet diameter of vaned diffuser on performance of the centrifugal pump. Structured grids of high quality were applied on the whole computational domain. Experimental results were acquired by prototype experiments and were then compared with the numerical results. Both experimental and numerical results show that the performance of a pump with a diffuser of smaller outlet diameter is better than of bigger outlet diameter under all operating conditions. The radial force imposed on the impeller obtained by unsteady numerical simulation was analyzed. The results also indicated that an appropriate decrease in the outlet diameter of the diffuser vane could increase the radial force.

Numerical study on instantaneous radial force of a centrifugal pump for different working conditions

2019 ◽  
Vol 37 (2) ◽  
pp. 458-480
Author(s):  
Xiaoqi Jia ◽  
Sheng Yuan ◽  
Zuchao Zhu ◽  
Baoling Cui
Keyword(s):  
Numerical Simulation ◽  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Working Conditions ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Radial Force ◽  
Leakage Rate ◽  
Content Type ◽  
Three Components

Purpose Instantaneous radial force induced from unsteady flow will intensify vibration noise of the centrifugal pump, especially under off-design working conditions, which will affect safety reliability of pump operation in severe cases. This paper aims to conduct unsteady numerical computation on one centrifugal pump; thus, unsteady fluid radial force upon the impeller and volute is obtained, so as to study the evolution law of instantaneous radial force, the internal relationship between radial force and pressure pulsation, the relationship among each composition of radial force that the impeller received and the influence of leakage rate of front and back chamber on radial force. Design/methodology/approach The unsteady numerical simulation with SST k-ω turbulence model was carried out for a low specific-speed centrifugal pump using computational fluid dynamics codes FLUENT. The performance tests and pressure tests were conducted by a closed loop system. The performance curves and the pressure distribution from numerical simulation agree with that of the experiment conducted. The unsteady pressure distributions and the instantaneous radial forces induced from unsteady flow were analyzed under different flow rates. Contribution degrees of three components of the radial force on the impeller and the relation between the radial force and leakage rate were analyzed. Findings Radial force on the volute and pressure pulsation on the volute wall have the same distribution tendency, but in contrast to the distribution trend of the radial force on the impeller. In the component of radial force that the impeller received, radial force on the blade accounts for the main position. With the decrease of flow rate, ratio of the radial force on front and back casings will be increased; under large flow rate, vortex and flow blockage at volute section will enhance the pressure and radial force fluctuation greatly, and the pulsation degree may be much more intense than that of a smaller flow rate. Originality/value This paper revealed the relation of the radial force and the pressure pulsation. Meanwhile, contribution degrees of three components of the radial force on the impeller under different working conditions as well as the relation between the radial force and leakage rate of front and rear chambers were analyzed.

scholarly journals Flow field analysis of multi-stage middle-open centrifugal pump inter-stage flow passage

2020 ◽  
Vol 155 ◽  
pp. 01014
Author(s):  
Xiao Zhang ◽  
He Huang
Keyword(s):  
Energy Loss ◽  
Centrifugal Pump ◽  
Guide Vane ◽  
Fluid Flows ◽  
Field Analysis ◽  
Original Design ◽  
Flow Passage ◽  
Guide Vanes ◽  
Multi Stage ◽  
Flow Field Analysis

In order to study the flow velocity, static pressure and turbulent kinetic energy distribution of the inter-stage flow passage, the numerical calculation of the inter-stage flow passage of the multistage split centrifugal pump was carried out under the design condition. The results show that the fluid flows along the inter-stage water flow channel, and backflow and vortices are generated at the guide vanes at the end of the bridge, which causes certain energy loss. In this paper, based on the original design, three different improvement schemes are proposed by changing the shape and position of the guide vane for the backflow and vortex generated near the guide vanes. The improved scheme is numerically simulated, and the energy loss values of the four different flow passages are calculated by integration. After comparison and analysis, the second scheme is determined as the best scheme, and the accuracy of simulation is verified by experiments.

Study on Internal Flow and External Performance of a Semi-open Impeller Centrifugal Pump with Different Tip Clearances

2015 ◽  
Vol 32 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Xiao-Qi Jia ◽  
Bao-Ling Cui ◽  
Yu-Liang Zhang ◽  
Zu-Chao Zhu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Tip Clearance ◽  
Evolution Process ◽  
And Performance ◽  
Unsteady Numerical Simulation

AbstractTo study the influence of tip clearance on internal flow characteristics and external performance of a prototype centrifugal pump with a semi-open impeller, the unsteady numerical simulation and performance experiments are carried out in this paper. The evolution process of leakage vortex with time

Based on CFX Numerical Simulation of Francis Turbine Runner

2013 ◽  
Vol 456 ◽  
pp. 207-210
Author(s):  
Fang He
Keyword(s):  
Numerical Simulation ◽  
Guide Vane ◽  
Prediction Method ◽  
Internal Flow ◽  
Francis Turbine ◽  
Flow State ◽  
Hydro Turbine ◽  
Runner Blade ◽  
Vibration Prediction ◽  
Turbine Runner

This paper presents a vibration prediction method for Francis turbine: Provided with advanced CFX software, Numerical simulation of movable guide vane and Turbine runner’s internal flow state. From the source of hydraulic vibration, Focus on numerical analysis, numerical simulation for the cutting thickness of the runner blade. After analysis of the influence of the blade of hydraulic vibration. To explore new ways for the hydro turbine control hydraulic vibration.

Lateral Fluid Forces on Whirling Centrifugal Impeller (1st Report: Theory)

1987 ◽  
Vol 109 (2) ◽  
pp. 94-99 ◽  
Author(s):  
H. Shoji ◽  
H. Ohashi
Keyword(s):  
Potential Flow ◽  
Guide Vane ◽  
Flow Theory ◽  
Operating Conditions ◽  
Centrifugal Impeller ◽  
Flow Rates ◽  
Guide Vanes ◽  
Fluid Forces ◽  
Damping Effect ◽  
Whirling Motion

Lateral fluid forces acting on a rotating centrifugal impeller in whirling motion are analyzed using unsteady potential flow theory. Impellers operating in diffusers with and without vanes are modeled and the fluid forces calculated for different whirl speeds and flow rates. The influences of these parameters are clarified by parametric calculations. The results for whirling impellers operating in vaneless diffusers show that the fluid forces exert a damping effect on the rotor whirling motion at all operating conditions. The results for impellers operating in vaned diffusers or guide vanes show that the time averaged values of fluid forces remain almost unchanged, while there are significant instantaneous fluctuations due to the impeller/guide vane interactions.

Study on Radial Forces of Centrifugal Pumps With Various Collectors

2011 ◽  
Author(s):  
Zhongyong Pan ◽  
Junjie Li ◽  
Shuai Li ◽  
Shouqi Yuan
Keyword(s):  
Numerical Simulation ◽  
Pressure Distribution ◽  
Radial Force ◽  
Time Dependent ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Trade Off ◽  
Blade Passage ◽  
Design Choice ◽  
Radial Forces

Numerical simulation is presented to study the steady and unsteady radial forces in a centrifugal pump with various collectors. The radial forces are obtained by integrating the pressure distribution around the impeller circumference. The calculated radial forces both time-dependent and independent at different flow rates caused by the collectors are compared. The results show that some conclusions do not consistent with the conventional experience as the collectors with double volute and vaned volute significantly decrease the radial forces and the radial force close a circle during the period of one blade passage passing. The combination of impeller and double volute is a trade-off design choice as it has significantly decreased the radial forces than that of single volute and its configuration is more compact than that of vaned collector.

scholarly journals Effects of impeller trim on performance of two-stage self-priming centrifugal pump

2017 ◽  
Vol 9 (2) ◽  
pp. 168781401769249 ◽  
Author(s):  
Kai Wang ◽  
Zixu Zhang ◽  
Linglin Jiang ◽  
Houlin Liu ◽  
Yu Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Guide Vane ◽  
Radial Force ◽  
Design Flow ◽  
Two Stage ◽  
Rate Condition ◽  
Application Range ◽  
Save Energy

In order to save energy by broadening its application range, the influence of impeller trim on the performance of a two-stage self-priming centrifugal pump was numerically studied. The hydraulic performance experiments and self-priming experiments were carried out. And the unsteady performance of pressure fluctuation and radial force in the pump was analyzed. The results show that with the increase in impeller trim quantity, the best efficiency point of the pump would move to the small flow rate condition. Under the design flow rate, when both the two stages of the impeller were trimmed by 6%, head of the pump was reduced by 13%, efficiency of the pump was as well decreased by 1.69 percentage points, and self-priming time was increased by 1.7%. Thus, impeller trim can be used to meet the operating requirements in the head range of 94–107 m. With the increase in impellers trim quantity, the pressure fluctuation in the positive channel of the radial guide vane and the volute was smaller, while the radial force on the wall of radial guide vane and volute was also smaller.

Sign in / Sign up

Export Citation Format

Share Document