scholarly journals Numerical Simulation of Fine Particle Solid-Liquid Two-Phase Flow in a Centrifugal Pump

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Yanping Wang ◽  
Bozhou Chen ◽  
Ye Zhou ◽  
Jianfeng Ma ◽  
Xinglin Zhang ◽  
...  
Keyword(s):  
Particle Size ◽  
Internal Pressure ◽  
Centrifugal Pump ◽  
Fine Particle ◽  
Volume Concentration ◽  
Two Phase Flow ◽  
Solid Particles ◽  
Phase Flow ◽  
Two Phase ◽  
Solid Liquid

To study the effect of fine particle size and volume concentration on the performance of solid-liquid two-phase centrifugal pump, the mixture multiphase flow model, RNG k-ε turbulence model, and SIMPLEC algorithm were used to simulate the two-phase flow of the centrifugal pump. The effects of particle size and volume concentration on internal pressure distribution, solid volume distribution, and external characteristics were analyzed. The results show that under the design discharge conditions, with the increase of particle size and volume concentration, the internal pressure of the flow field will decrease, and the volume fraction of solid phase in the impeller passage will also decrease as a whole. The solid particles gradually migrate from the suction surface to the pressure surface, and the particles in the volute channel are mainly concentrated in the flow channel near the outlet side of the volute. With the increase of particle size and volume concentration, the negative pressure value at the inlet of centrifugal pump increases, the total pressure difference at the inlet and outlet decreases, and the head and efficiency decrease accordingly.

scholarly journals Wear Characteristics of Dense Fine Particles Solid-Liquid Two-Phase Fluid Centrifugal Pump with Open Impellers

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Yanping Wang ◽  
Chuanfeng Han ◽  
Ye Zhou ◽  
Zhe Lin ◽  
Jianfeng Ma ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Volume Concentration ◽  
Fine Particles ◽  
Two Phase Flow ◽  
Middle Part ◽  
Phase Flow ◽  
Particle Volume ◽  
Two Phase ◽  
Wear Characteristics

The demand for a centrifugal pump with open impellers for conveying dense fine particles in solid-liquid two-phase flow has increased significantly in actual engineering. The wear of dense fine particles on the centrifugal pump is also exceedingly prominent, which affects the engineering efficiency and economic benefits. The two-phase flow in the open centrifugal pump is three-dimensional and unsteady; the movement of high-volume concentration particles in the centrifugal pump and its mutual influence on the two-phase flow, which results in the calculation of wear, are very intricate. To study the wear characteristics of the centrifugal pump with open impeller with high-volume concentration particles more accurately, numerical simulation and experimental comparison are carried out for the impeller wear of dense fine particles transported by the centrifugal pump with open impellers. Considering the relationship between particles and walls, we used the Fluent 18.0 built-in rebound function and wear model. The RNG k-ε model and the DDPM model were adopted in the numerical simulation, and the numerical solution for centrifugal pump wear was performed under flow rate (9.6 m3·h−1, 12.8 m3·h−1, 16 m3·h−1, and 19.2 m3·h−1), different particle sizes (0.048 mm, 0.106 mm, 0.15 mm, 0.27 mm, and 0.425 mm), and different particle volume concentrations (10%, 15%, 20%, 25%, and 30%), respectively. By comparing the serious wear positions of the impeller, the experimental results correspond well with the numerical simulation, which can be used to predict and study the wear characteristics of the impeller. The results show that the most serious area of blade wear is the middle part of the pressure surface, followed by the middle part of the upper part of the blade. The wear of the impeller is greatly affected by relevant parameters, such as pump flow rate, particle diameter, and particle volume concentration. These results can provide some basis for the wear-resistant design of dense fine particle impeller.

Solid–liquid two-phase flow and erosion calculation of butterfly valves at small opening based on DEM method

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Benliang Xu ◽  
Zuchao Zhu ◽  
Zhe Lin ◽  
Dongrui Wang
Keyword(s):  
Peer Review ◽  
Two Phase Flow ◽  
Solid Particles ◽  
Phase Flow ◽  
Butterfly Valve ◽  
Two Phase ◽  
Content Type ◽  
Small Opening ◽  
Solid Liquid ◽  
The Impact

Purpose The study aims to decrease the effect of solid particles on a butterfly valve, which will cause seal failure and leakage, providing a reference for anti-wear design. Design/methodology/approach In this paper, computational fluid dynamics discrete element method (CFD-DEM) simulation was conducted to study the solid–liquid two-phase flow characteristics and erosion characteristics of a butterfly valve with a different opening. Findings Abrasion at 10% opening is affected by high-speed jets in upper and lower parts of the pipeline, where the erosion is intense. The impact of the jet on the upper part of 20% opening begins to weaken. With the top backflow vortex disappearing, the effect of lower jet is enhanced. Meanwhile, the bottom backflow vortex phenomenon is obvious, and the abrasion position moves downward. At 30% opening, the velocity is further weakened, and the circulation effect of lower flow channel is more obvious than that of the upper one. Originality/value It is the first time to use DEM to investigate the two-phase flow and erosion characteristics at a small opening of a butterfly valve, considering the effect of inter-particle collision. Therefore, this study carries on the thorough analysis and discussion. At the same opening degree, with increasing of the particle size, the abrasion of valve frontal surface increases when the size is less than 150 µm and decreases when it is greater than 150 µm. For the valve backflow surface, this boundary value becomes 200 µm. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2020-0264/

scholarly journals Study on the Effects of the Wear-Rings Clearance on the Solid-Liquid Two-Phase Flow Characteristics of Centrifugal Pumps

Symmetry ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2003
Author(s):  
Chaoshou Yan ◽  
Jianfei Liu ◽  
Shuihua Zheng ◽  
Bin Huang ◽  
Jiacheng Dai
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Centrifugal Pumps ◽  
Suction Surface ◽  
Two Phase ◽  
Wear Area ◽  
Fluid Medium ◽  
Solid Liquid

In order to study the wear law of the centrifugal pump flowing surface under different wear-rings clearance, the McLaury wear model was used to conduct the full-passage numerical simulation of solid-liquid two-phase flow in a single-stage single-suction centrifugal pump. The reliability of the numerical calculation method is verified by comparing the experimental data and numerical simulation results. The clearance is 0.1, 0.15, 0.2, 0.3 and 0.5 mm, respectively. The results show that the wear of the centrifugal pump blades is mainly concentrated in the end part and the inlet part of the blade, and the wear of the pressure surface at the end of the suction surface and the front of the blade is more serious. As the clearance increases, the maximum wear value in the impeller increases first and then decreases, reaching a maximum at 0.15 mm. With the increase of the clearance, the wear degree and the wear rate of the volute wall surface first increase and then decrease, and reach the maximum at 0.2 mm. With the increase of the clearance and the concentration of the fluid medium, the wear at the clearance of the centrifugal pump is more serious, and the severe wear area exhibits a point-like circumferential distribution.

Numerical and experimental research on the erosion of solid-liquid two-phase flow in transport butterfly valve based on DEM method

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Benliang Xu ◽  
Zuchao Zhu ◽  
Zhe Lin ◽  
Dongrui Wang ◽  
Guangfei Ma
Keyword(s):  
Particle Size ◽  
Turbulence Model ◽  
High Speed ◽  
Two Phase Flow ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Butterfly Valve ◽  
Two Phase ◽  
Content Type ◽  
Solid Liquid

Purpose The purpose of this paper is to analyze the mechanism of particle erosion in butterfly valve pipelines under hydraulic transportation conditions. The results will affect the sealing and safety of butterfly valve pipelines and hopefully serve as reference for the anti-erosion design of butterfly valve pipelines. Design/methodology/approach Through the discrete element method (DEM) simulation that considers the force between particles, the detached eddy simulation (DES) turbulence model based on realizable k-epsilon is used to simulate the solid-liquid two-phase flow-induced erosion condition when the butterfly valve is fully opened. The simulation is verified by building an experimental system correctness. The solid-liquid two-phase flow characteristics, particle distribution and erosion characteristics of the butterfly valve pipeline under transportation conditions are studied. Findings The addition of particles may enhance the high-speed area behind the valve. It first increases and then decreases with increasing particle size. With increasing particle size, the low-velocity particles change from being uniformly distributed in flow channel to first gathering in the front of the valve and, then, to gathering in lower part of it. Fluid stagnation at the left arc-shaped flange leads to the appearance of two high-speed belts in the channel. With increasing fluid velocity, high-speed belts gradually cover the entire valve surface by focusing on the upper and lower ends, resulting in the overall aggravation of erosion. Originality/value Considering the complexity of solid-liquid two-phase flow, this is the first time that the DEM method with added inter-particle forces and the DES turbulence model based on realizable k-epsilon has been used to study the flow characteristics and erosion mechanism of butterfly valves under fully open transportation conditions.

Measurement of flow rate in solid-liquid two-phase flow in pipes at low volume concentration with venturimeter

Measurement ◽  
2019 ◽  
Vol 138 ◽  
pp. 409-415
Author(s):  
Liyan Wang ◽  
Saiwei Li ◽  
Ye Yuan ◽  
Zhiqiang Sun ◽  
Tian Zhou
Keyword(s):  
Flow Rate ◽  
Volume Concentration ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Low Volume ◽  
Solid Liquid

Numeration Simulation of Solid-Liquid Two-Phase Flow in Centrifugal Sewerage Pump

2010 ◽  
Vol 44-47 ◽  
pp. 345-348 ◽  
Author(s):  
Jian Hua Liu ◽  
Ming Yi Zhu
Keyword(s):  
Particle Size ◽  
Solid Particle ◽  
Working Condition ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Phase Flow ◽  
Operation Condition ◽  
Two Phase ◽  
And Performance ◽  
Solid Liquid

By Means of Fluent 6.3，the paper simulated the solid-liquid two-phase flow to a centrifugal sewerage pump，using Eulerian Mixture Model under different working condition and different particle size. The simulation draws some conclusion on distributive rules of solid particle inside impeller passage. The results for this simulation were as following: Distributive rules of solid particle inside impeller passage mainly relate to particle size. Meanwhile，the volume fraction of particles and operation condition have influence on distributive rules of solid particle. The simulated results can explain commendably that attrition took place inside pump passage when pump transported solid-liquid two-phase flow. Meanwhile，the simulated results have reference price to improve the design for pump and performance of pump.

Turbulent Solid-Liquid Two-Phase Flow Simulation With Turbulence Intensity and Time Scale Model

2009 ◽  
Author(s):  
Z. Mansoori ◽  
M. Saffar-Avval ◽  
B. Nojabaii ◽  
F. Behzad ◽  
G. Ahmadi
Keyword(s):  
Time Scale ◽  
Model Comparison ◽  
Two Phase Flow ◽  
Solid Phase ◽  
Solid Particles ◽  
Scale Model ◽  
Particle Collision ◽  
Phase Flow ◽  
Two Phase ◽  
Solid Liquid

Two-dimensional simulation of turbulent solid-liquid flow is carried out. The modeling is established for a two-phase flow of solid particles in a vertical pipe water flow. Governing equations of flow and turbulence field are solved in an Eulerian-Lagrangian approach by the use of k-τ (turbulence time scale) model and trajectories of the particles are obtained using the Lagrangian method with a deterministic inter-particle collision model. Comparison between the results of the model for mean and r.m.s velocities of the liquid and solid phase with the experimental results shows a good agreement. The effect of variation of particle density and concentration are studied.

Sign in / Sign up

Export Citation Format

Share Document