scholarly journals Effect of Low Ambient Pressure on Spray Cone Angle of Pressure Swirl Atomizer

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Zhengyan Guo ◽  
Yi Jin ◽  
Kai Zhang ◽  
Kanghong Yao ◽  
Yunbiao Wang ◽  
...  
Keyword(s):  
High Speed ◽  
Ambient Pressure ◽  
Cone Angle ◽  
Spray Angle ◽  
High Speed Photography ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

Pressure swirl atomizers are widely used in gas turbine combustor; this paper is aimed at researching the effect of low ambient pressure (0.1 MPa to 0.01 MPa, lower than an atmosphere) on the spray cone angle of pressure swirl atomizer. The spray angle is captured by high-speed photography; then, an image post program is used to process the spray angle magnitude. A mathematical model of a single droplet’s movement and trajectory based on force analysis is proposed to validate the spray angle variation. The maximum variation of the spray cone angle, which is observed when fuel supply pressure drop through the atomizer is 1 MPa as the ambient pressure decreases from 0.1 MPa to 0.01 MPa, is found to be 23.9%. The experimental results show that the spray cone angle is expected to increase with the ambient pressure decrease; meanwhile, mathematical results agree well with this trend.

scholarly journals Influence of orifice geometry on atomization characteristics of pressure swirl atomizer

2020 ◽  
Vol 103 (3) ◽  
pp. 003685042095018
Author(s):  
Huilong Zheng ◽  
Zhaomiao Liu ◽  
Kaifeng Wang ◽  
Jiayuan Lin ◽  
Zexuan Li
Keyword(s):  
High Speed ◽  
Cone Angle ◽  
Spray Angle ◽  
Orifice Diameter ◽  
High Speed Photography ◽  
Spray Cone Angle ◽  
Experimental Conditions ◽  
Spray Cone ◽  
Velocity Magnitude ◽  
Pressure Swirl

The spray characteristics of the pressure swirl nozzle are experimentally studied using particle dynamics analysis (PDA) and high-speed photography system in this paper, specifically focusing on the dependence of geometrical dimensions of orifice on the spray SMD, velocity magnitude and droplet distribution, and the spray cone angle. It is indicated that the increase of orifice diameter makes the initial swirling velocity lower and the spray liquid film thicker. When the spray cone is fully expanded, the flow rate of 900 μm orifice diameter nozzle increases by 30–40% and the SMD of 900 μm orifice diameter nozzle increases by 8.5% compared with that of 700 μm orifice diameter nozzle. According to the experimental conditions, the relationship between Re and spray angle was calculated as θ = 29.97*Re0.087, ignoring the factors that had little influence on spray angle. The decrease of the orifice length makes the distance of gas-medium shearing action shorten so that thinner oil film near wall cannot be formed by the extrusion of air core, leading to the swirling intensity reducing and the suction effect weakened. The spray cone angle of the 450 μm orifice length atomizer is about 5° smaller than the nozzle of 500 μm orifice length, and more small SMD droplets are not sucked, resulting in the distribution range of spray SMD declining.

Numerical Analysis of Pressure Swirl Atomizer

2015 ◽  
Vol 798 ◽  
pp. 190-194
Author(s):  
Mehmet Kahraman ◽  
Guven Komurgoz ◽  
Ibrahim Ozkol
Keyword(s):  
Cone Angle ◽  
Computational Cost ◽  
Internal Flow ◽  
Combustion Engines ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

Atomization quality of liquids has a great importance on the performance of combustion engines. In this study the internal flow phenome of pressure swirl atomizer is investigated by using numerical method. The design of swirl atomizer is performed based on the requested atomizer characteristics which are sauter mean diamer (SMD), spray cone angle and break up length. Prediction and understanding of liquid film dynamics in the atomizer inside are the fundamental ways to explore atomizer performance. The purpose of this study is to estimate the air core size and film thickness in pressure swirl atomizer by setting single phase numeric computations. This article concludes that the CFD validated swirl atomizer design can be achieved with the lower computational cost using stream function methodology.

Effect of Liquid/Gas Density Ratio on Primary Jet Breakup of Pressure Swirl Atomizer: Experimental and Numerical Study

2019 ◽  
Author(s):  
Edin Michael ◽  
Santhosh Kumar Keerthi ◽  
Krishna Kant ◽  
Pankaj Kolhe ◽  
Raja Banerjee ◽  
...  
Keyword(s):  
Numerical Study ◽  
Cone Angle ◽  
Density Ratio ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Gas Density ◽  
Jet Breakup ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

Abstract This work reports experimental and numerical study of primary jet breakup of a pressure swirl atomizer. Experiments were performed in a constant volume spray chamber and the spray pattern was characterized as a function of different liquid/gas density ratios which was achieved by changing the ambient pressure. The liquid/gas density ratio was varied between ≈ 102 to 103 and the axial Reynold number was maintained at 6 × 103. Diffused backlight imaging in conjunction with high speed videography was used to visualize the spray. Parameters like spray cone angle, spray breakup length and flapping frequency was estimated. Additionally, POD analysis was performed to find the sheet instability modes. A corresponding numerical study using Coupled Level Set VOF method was performed keeping the liquid/gas density ratio of 10 and 102 to simulate the primary jet breakup using an in-house two-phase solver developed using OpenFOAM libraries. The solver was validated by following the numerical work of Fuster et al. Effect of computational mesh size on parameters like spray cone angle, breakup length was estimated.

Pressure-Scaling of Pressure-Swirl Atomizer Cone Angles

2008 ◽  
Vol 130 (6) ◽  
Author(s):  
D. R. Guildenbecher ◽  
R. R. Rachedi ◽  
P. E. Sojka
Keyword(s):  
Pressure Drop ◽  
Ambient Pressure ◽  
Cone Angle ◽  
Spray Angle ◽  
Subsequent Increase ◽  
A Value ◽  
Nozzle Pressure ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

An experimental investigation was conducted to study the effects of increased ambient pressure (up to 6.89MPa) and increased nozzle pressure drop (up to 2.8MPa) on the cone angles for sprays produced by pressure-swirl atomizers having varying amounts of initial swirl. This study extends the classical results of DeCorso and Kemeny, (1957, “Effect of Ambient and Fuel Pressure on Nozzle Spray Angle,” ASME Transactions, 79(3), pp. 607–615). Shadow photography was used to measure cone angles at x∕D0=10, 20, 40, and 60. Our lower pressure results for atomizer swirl numbers of 0.50 and 0.25 are consistent with those of DeCorso and Kemeny, who observed a decrease in cone angle with an increase in nozzle pressure drop, ΔP, and ambient density, ρair, until a minimum cone angle was reached when ΔPρair1.6∼100MPa(kg∕m3)1.6 (equivalent to 200psi(lbm∕ft3)1.6). Results for atomizers having higher initial swirl do not match the DeCorso and Kemeny results as well, suggesting that their correlation be used with caution. Another key finding is that an increase in ΔPρair1.6 to a value of 600MPa(kg∕m3)1.6 leads to continued decrease in cone angle, but that a subsequent increase to 2000MPa(kg∕m3)1.6 has little effect on cone angle. Finally, there was little effect of nozzle pressure drop on cone angle, in contrast to findings of previous workers. These effects are hypothesized to be due to gas entrainment.

Influence of Ambient Air Pressure on Pressure-Swirl Atomization

1987 ◽  
Author(s):  
X. F. Wang ◽  
A. H. Lefebvre
Keyword(s):  
Drop Size ◽  
Cone Angle ◽  
Ambient Air ◽  
Air Pressure ◽  
Spray Angle ◽  
Flow Number ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Continuous Increase ◽  
Pressure Swirl

The spray characteristics of six simplex atomizers are examined in a pressure vessel using a standard light diffraction technique. Attention is focused on the effects of liquid properties, nozzle flow number, spray cone angle, and ambient air pressure on mean drop size and drop-size distribution. For all nozzles and all liquids it is found that continuous increase in air pressure above the normal atmospheric value causes the SMD to first increase up to a maximum value and then decline. An explanation for this characteristic is provided in terms of the measurement technique employed and the various competing influences on the overall atomization process. The basic effect of an increase in air pressure is to improve atomization, but this trend is opposed by contraction of the spray angle which reduces the relative velocity between the drops and the surrounding air, and also increases the possibility of droplet coalescence.

Experimental investigations of kerosene sprays in pressurized evaporating environments

2018 ◽  
Vol 233 (3) ◽  
pp. 413-427 ◽  
Author(s):  
Tao Liu ◽  
Wei Fu ◽  
Bolun Yi ◽  
Lanbo Song ◽  
Qizhao Lin ◽  
...  
Keyword(s):  
Experimental Data ◽  
Ambient Temperature ◽  
High Speed ◽  
Ambient Pressure ◽  
Cone Angle ◽  
Experimental Investigations ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Ambient Temperatures ◽  
Performance And Emissions

Experiments of kerosene spray with single-hole solenoid injector in the pressurized nonevaporating and evaporating environments, in which the ambient pressure ranges from 1.4 MPa to 4.8 MPa and the ambient temperature includes 300 K, 343 K, and 423 K, are carried out with high-speed Schlieren photography to investigate the breakup regimes and the macro-characteristics like penetration, projected spray area, and spray cone angle. Repetitive experiments are conducted to analyze the penetration repeatability. The comparison between the experimental penetrations and the predicted ones by the existing correlations reveals that the deviations between the experimental data and the predictions rise as the ambient temperature rises. Therefore, a new modified correlation is proposed to predict the penetration of kerosene spray in the nonevaporating and evaporating environments, which fits the experimental data better than the existing correlations. The breakup regimes in primary breakup and secondary breakup are discussed respectively. The projected spray area is analyzed under different ambient pressures at different ambient temperatures. Finally, it is found that the spray cone angle remains almost the same under different ambient pressures after it reduces sharply before 0.5 ms. The macro-characteristics discussed in the present study are important for the performance and emissions of aeronautical engines or diesel engines fuelled by kerosene as a substitution.

Pressure-Scaling of Pressure-Swirl Atomizer Cone Angles

2006 ◽  
Author(s):  
D. R. Guildenbecher ◽  
R. R. Rachedi ◽  
P. E. Sojka
Keyword(s):  
Pressure Drop ◽  
Ambient Pressure ◽  
Cone Angle ◽  
Subsequent Increase ◽  
Gas Entrainment ◽  
A Value ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer ◽  
Measure Cone

An experimental investigation was conducted to study the effects of increased ambient pressure (up to 6.89 MPa) and increased nozzle pressure drop (up to 2.8 MPa) on the cone angles for sprays produced by pressure-swirl atomizers having varying amounts of initial swirl. This study extends the classical results of DeCorso and Kemeny [1]. Shadow photography was used to measure cone angles at x/D0=10, 20, 40, and 60. Our lower pressure results for atomizer swirl numbers of 0.50 and 0.25 are consistent with those of DeCorso and Kemeny [1], who observed a decrease in cone angle with an increase in a pressure drop-ambient density product until a minimum cone angle was reached at ΔPρair1.6~200. Results for atomizers having higher swirl numbers do not match the DeCorso and Kemeny [1] results as well, suggesting that their correlation be used with caution. Another key finding is that an increase in ΔPρair1.6 to a value of 1000 leads to continued decreases in cone angle, but that a subsequent increase to 4000 has little effect on cone angle. Finally, there was little influence of atomizer pressure drop on cone angle, in contrast to findings of previous workers. These effects are hypothesized to be due to gas entrainment.

Experimental Investigations of Performance Parameters of Pressure Swirl Atomizer for Kerosene Type Fuel

2009 ◽  
Author(s):  
Saurabh Dikshit ◽  
Salim Channiwala ◽  
Digvijay Kulshreshtha ◽  
Kamlesh Chaudhari
Keyword(s):  
Drop Size ◽  
Mechanical Energy ◽  
Cone Angle ◽  
Experimental Investigations ◽  
Performance Parameters ◽  
Spray Cone ◽  
Spray Penetration ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

The process of atomization is one in which a liquid jet or sheet is disintegrated by the kinetic energy of the liquid itself, or by exposure to high velocity air or gas, or as a result of mechanical energy applied externally. Combustion of liquid fuels in engines and industrial furnaces is dependent on effective atomization to increase the specific surface area of the fuel and thereby achieve high rate of mixing and evaporation. The pressure swirl atomizer is most common type atomizer used for combustion in gas turbine engines and industrial furnaces. The spray penetration is of prime importance for combustion designs. Over penetration of the spray leads to impingement of the fuel on walls of furnaces and combustors. On the other hand, if spray penetration is inadequate, fuel–air mixing is unsatisfactory. Optimum engine performance is obtained when the spray penetration is matched to the size and geometry of combustors. Methods for calculating penetration are therefore essential to sound engine design. Equally important are the spray cone angles and the drop size distribution in the sprays. An attempt is being made to experimentally investigate pressure swirl atomizer performance parameters such as spray cone angle, penetration length and drop size at different injection pressures ranging from 6 bar to 18 bar.

Influence of Ambient Air Pressure on Pressure-Swirl Atomizer Spray Characteristics

2001 ◽  
Author(s):  
Arvind K. Jasuja ◽  
Arthur H. Lefebvre
Keyword(s):  
Gas Turbines ◽  
Drop Size ◽  
Cone Angle ◽  
Ambient Air ◽  
Air Pressure ◽  
Spray Characteristics ◽  
Spray Cone ◽  
Swirl Atomizer ◽  
Pressure Swirl ◽  
Pressure Swirl Atomizer

A single-component PDPA is used to evaluate the spray characteristics of a simplex pressure-swirl atomizer when operating at high liquid flow rates and elevated ambient air pressures. Attention is focused on the effects of air pressure on mean drop size, drop-size distribution, mean velocity, volume flux, and number density. Using a constant flow rate of 75 g/s, measurements are carried out along the spray radii at a fixed distance downstream from the atomizer face of 50 mm. The air pressures of 1, 8, and 12 bars chosen for these tests correspond to air densities of 1.2, 9.6, and 14.4 kg/m3. The purpose of the investigation is to supplement the existing body of information on pressure-swirl spray characteristics, most of which were obtained at normal atmospheric ambient pressures, with new data that correspond more closely to the conditions prevailing in the primary combustion zones of modern gas turbines. The results obtained are explained mainly in terms of the influence of air pressure on spray structure, in particular spray cone angle and Weber number.

Sign in / Sign up

Export Citation Format

Share Document