scholarly journals Numerical Performance Investigation of Parabolic Dish Solar-Assisted Cogeneration Plant Using Different Heat Transfer Fluids

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Muhammad Sajid Khan ◽  
Muhammad Abid ◽  
Khuram Pervez Amber ◽  
Hafiz Muhammad Ali ◽  
Mi Yan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Solar Collector ◽  
Integrated System ◽  
Operating Conditions ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Pressurized Water ◽  
Parabolic Dish ◽  
Process Heating

Parabolic dish solar collectors gain higher solar to thermal conversion efficiency due to their maximum concentration ratio. The present research focuses by integrating the parabolic dish solar collector to the steam cycle producing power and rate of process heating. Pressurized water, therminol VP1, and supercritical carbon dioxide are the examined working fluids in the parabolic dish solar collector. The aim of the current research is to observe the optimal operating conditions for each heat transfer fluid by varying inlet temperature and flow rate of the working fluid in the parabolic dish solar collector, and combination of these parameters is predicted to lead to the maximum energy and exergy efficiencies of the collector. The operating parameters are varied to investigate the overall system efficiencies, work output, and process heating rate. Findings of the study declare that water is an efficient heat transfer fluid at low temperature levels, whereas therminol VP1 is effective for a higher temperature range. The integrated system efficiencies are higher at maximum flow rates and low inlet temperatures. The efficiency map of solar collector is located at the end of study, and it shows that maximum exergy efficiency gains at inlet temperature of 750 K and it is observed to be 37.75%.

Thermodynamic Performance Evaluation of a Solar Parabolic Dish Assisted Multigeneration System

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Muhammad Abid ◽  
Muhammad Sajid Khan ◽  
Tahir Abdul Hussain Ratlamwala
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Integrated System ◽  
Heat Transfer Fluid ◽  
Outlet Temperature ◽  
Parabolic Dish ◽  
Single Effect

The concentration ratio of the parabolic dish solar collector (PDSC) is considered to be one of the highest among the concentrated solar power technologies (CSPs); therefore, such system is capable of generating more heat rate. The present paper focuses on the integration of the PDSC with the combined cycle (gas cycle as the toping cycle and steam cycle as the bottoming cycle) along with the utilization of waste heat from the power cycle to drive the single effect lithium bromide/water absorption cycle. Molten salt is used as a heat transfer fluid in the solar collector. The engineering equation solver (EES) is employed for the mathematical modeling and simulation of the solar integrated system. The various operating parameters (beam radiation, inlet and ambient temperatures of heat transfer fluid, mass flow rate of heat transfer fluid, evaporator temperature, and generator temperature) are varied to analyze their influence on the performance parameters (power output, overall energetic and exergetic efficiencies, outlet temperature of the receiver, and as coefficient of performance (COP) and exergy efficiencies) of the integrated system. The results show that the overall energy and exergy efficiencies are observed to be 39.9% and 42.95% at ambient temperature of 27 °C and solar irradiance of 1000 W/m2. The outlet temperature of the receiver is noticed to decrease from 1008 K to 528 K for an increase in the mass flow rate from 0.01 to 0.05 kg/s. The efficiency rate of the power plant is 38%, whereas COP of single effect absorption system is 0.84, and it will decrease from 0.87 to 0.79. However, the evaporator load is decreased to approximately 9.7% by increasing the generator temperature from 47 °C to 107 °C.

The Effects of Spraying Parameters on Spray Cooling Heat Transfer Performance in the Non-Boiling Regime

2017 ◽  
Author(s):  
Azzam S. Salman ◽  
Jamil A. Khan
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Target Surface ◽  
Spray Cooling ◽  
Operating Conditions ◽  
Droplet Velocity ◽  
Inlet Pressure ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Spraying Parameters

Experiments were conducted in a closed loop spray cooling system working with deionized water as a working fluid. This study was performed to investigate the effect of the spraying parameters, such as Sauter mean diameter (SMD), the droplet velocity, and the residual velocity on the spray cooling heat transfer in the non-boiling region. Thermal effects on plain and modified surfaces with circular grooves were examined under different operating conditions. The inlet pressure of the working fluid was varied from 78.6 kPa to 183.515kPa, and the inlet temperature was kept between 21–22 °C. The distance between the nozzle and the target surface 10 mm. The results showed that increasing the coolant inlet pressure increases the droplet velocity and the number of droplets produced while decreasing the droplet size. As a consequence of these changes, increasing inlet pressure improved the heat transfer characteristics of both surfaces.

Geothermal Power Cycle Analysis for Commercial Applicability Using Sequestered Supercritical CO2 as a Heat Transfer or Working Fluid

2011 ◽  
Author(s):  
Brian Janke ◽  
Thomas Kuehn
Keyword(s):  
Heat Transfer ◽  
Binary System ◽  
Power Plants ◽  
Power Production ◽  
Operating Conditions ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Direct System ◽  
Geothermal Power ◽  
The Impact

Thermodynamic analysis has been conducted for geothermal power cycles using a portion of deep ground sequestered CO2 as the working fluid. This allows energy production from much shallower depths and in geologic areas with much lower temperature gradients than those of current geothermal systems. Two different system designs were analyzed for power production with varying reservoir parameters, including reservoir depth, temperature, and CO2 mass flow rate. The first design is a direct single-loop system with the CO2 run directly through the turbine. This system was found to provide higher system efficiency and power production, however design complications such as the need for high pressure turbines, two-phase flow through the turbine and the potential for water-CO2 brine mixtures, could require the use of numerous custom components, driving up the cost. The second design is a binary system using CO2 as the heat transfer fluid to supply thermal energy to an Organic Rankine Cycle (ORC). While this system was found to have slightly less power production and efficiency than the direct system, it significantly reduces the impact of design complications associated with the direct system. This in turn reduces the necessity for certain custom components, thereby reducing system cost. While performance of these two systems is largely dependent on location and operating conditions, the binary system is likely applicable to a larger number of sites and will be more cost effective when used in combination with current off-the-shelf ORC power plants.

scholarly journals Heat Transfer Augmentation of Concentrated Solar Absorber Using Modified Surface Contour

2021 ◽  
Vol 11 (1) ◽  
pp. 24-33
Author(s):  
Ramalingam Senthil ◽  
Arvind Chezian ◽  
Zackir Hussain Ajmal Arsath
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Cavity Surface ◽  
Solar Absorbers ◽  
Surface Contour ◽  
Parabolic Dish ◽  
Plain Surface ◽  
Surface Modified

This work aims to compare the cavity surface contour’s thermal performance to that of the solar absorber’s plain surface contour for Scheffler type parabolic dish collectors. The absorber is tested for the temperature range up to 600°C without working fluid and 180°C with the working fluid. The modified absorber surface's thermal performance is compared with the flat surface absorber with and without heat transfer fluid. The peak temperature reached by the surface modified absorber (534°C) is about 8.6% more than that of the unmodified absorber (492°C) during an outdoor test without fluid. The energy efficiency of cavity surface absorber and plain surface absorber are 67.65% and 61.84%, respectively. The contoured cavity surface produces a more uniform temperature distribution and a higher heat absorption rate than the plain surface. The results are beneficial to the design of high-temperature solar absorbers for concentrated solar collectors.

Numerical Model for Storage Systems Based on Phase-Change Materials

2011 ◽  
Author(s):  
Adriano Sciacovelli ◽  
Vittorio Verda ◽  
Francesco Colella
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Materials ◽  
Storage Systems ◽  
Numerical Procedure ◽  
Thermal Storage ◽  
Operating Conditions ◽  
Heat Transfer Fluid ◽  
Inlet Temperature ◽  
Technical Problems

Phase-change materials (PCM) are particularly promising for thermal storage in various energy plants as solar plants, district heating, heat pumps, etc. mainly because of the possibility to reduce the volume of storage tanks, but also because the problems related with thermal stratification are considerably reduced. On the other hand, research is necessary in order to address technical problems, mainly related to the heat transfer in the medium, which needs to be enhanced in order to achieve reasonable charging and discharging processes. The present paper describes the application of computational fluid-dynamics (CFD) for the analysis of PCM thermal storage systems. The numerical analysis is directed at understanding the role of buoyancy-driven convection during constrained solidification and melting inside a shell-and-tube geometry. The 2D model is based on a finite-volume numerical procedure that adopts the enthalpy method to take in account the phase change phenomenon. The time-dependent simulations show the melting phase front and melting fraction of the PCM and incorporate the fluid flow in the liquid phase. The obtained temperature profiles are compared to a set of experimental data available in the literature. The results show that during the melting process natural convection within the PCM has non negligible effects on the behavior of the system. The numerical simulations of the solidification process show that the increasing solid fraction of the PCM inhibits the buoyancy in the remaining liquid portion of the phase-change-material. Furthermore, the paper discusses the effects on the phase-change processes of the main operating conditions, including inlet temperature and mass flow rate of the heat transfer fluid.

scholarly journals Heat Transfer Augmentation of Concentrated Solar Absorber Using Modified Surface Contour

2021 ◽  
Vol 11 (1) ◽  
pp. 24-33
Author(s):  
Ramalingam Senthil ◽  
Arvind Chezian ◽  
Zackir Hussain Ajmal Arsath
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Cavity Surface ◽  
Solar Absorbers ◽  
Surface Contour ◽  
Parabolic Dish ◽  
Plain Surface ◽  
Surface Modified

This work aims to compare the cavity surface contour’s thermal performance to that of the solar absorber’s plain surface contour for Scheffler type parabolic dish collectors. The absorber is tested for the temperature range up to 600°C without working fluid and 180°C with the working fluid. The modified absorber surface's thermal performance is compared with the flat surface absorber with and without heat transfer fluid. The peak temperature reached by the surface modified absorber (534°C) is about 8.6% more than that of the unmodified absorber (492°C) during an outdoor test without fluid. The energy efficiency of cavity surface absorber and plain surface absorber are 67.65% and 61.84%, respectively. The contoured cavity surface produces a more uniform temperature distribution and a higher heat absorption rate than the plain surface. The results are beneficial to the design of high-temperature solar absorbers for concentrated solar collectors.

Investigating the effect of using nanofluids on the performance of a double-effect absorption refrigeration cycle combined with a solar collector

2019 ◽  
Vol 234 (7) ◽  
pp. 981-993 ◽  
Author(s):  
Mohamad Aramesh ◽  
Fathollah Pourfayaz ◽  
Mehdi Haghir ◽  
Alibakhsh Kasaeian ◽  
Mohammad H Ahmadi
Keyword(s):  
Heat Transfer ◽  
Ag Nanoparticles ◽  
Pure Water ◽  
Double Effect ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Refrigeration Cycle ◽  
Outlet Temperature ◽  
Absorption Refrigeration

In this article, the performance of a double-effect LiBr-H2O absorption refrigeration cycle is studied and is improved by applying solar energy and utilizing nanofluids. A trough collector is used to preheat the working fluid before entering the generator of the cycle. In addition, four different nanofluids are considered as the heat transfer fluid of the collector: Al2O3, Ag, Cu, and CuO. The effects of using nanofluids on the outlet temperature of the heat transfer fluid, the temperature of the working fluid entering the generator, the heat produced by the generator, and COP of the cycle are studied. Different concentrations of the nanoparticles from 0 to 2.5% are considered for the nanofluids. The results indicate that in all the concentrations, Ag nanoparticles will have a better performance comparing to the other types. Furthermore, it was concluded that the higher concentrations of the nanoparticles and along with it the higher inlet temperature of the generator will decrease the generator heat production rate up to 4%. Moreover, considering the constant cooling capacity of the cycle, usage of the Ag nanoparticles in the concentration of 2.5% increases the value of COP up to 3.9%, with respect to the pure water.

Heat transfer characteristic modelling and the effect of operating conditions on re-cooled cycle for a scramjet

2011 ◽  
Vol 115 (1164) ◽  
pp. 83-90 ◽  
Author(s):  
W. Bao ◽  
J. Qin ◽  
W. X. Zhou
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Transfer Characteristic ◽  
Cooling Capacity ◽  
Sensitivity Study ◽  
Performance Model ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Fuel Flow ◽  
Temperature And Pressure

Abstract A re-cooled cycle has been proposed for a regeneratively cooled scramjet to reduce the hydrogen fuel flow for cooling. Upon the completion of the first cooling, fuel can be used for secondary cooling by transferring the enthalpy from fuel to work. Fuel heat sink (cooling capacity) is thus repeatedly used and fuel heat sink is indirectly increased. Instead of carrying excess fuel for cooling or seeking for any new coolant, the cooling fuel flow is reduced, and fuel onboard is adequate to satisfy the cooling requirement for the whole hypersonic vehicle. A performance model considering flow and heat transfer is build. A model sensitivity study of inlet temperature and pressure reveals that, for given exterior heating condition and cooling panel size, fuel heat sink can be obviously increased at moderate inlet temperature and pressure. Simultaneously the low-temperature heat transfer deterioration and Mach number constrains can also be avoided.

Sign in / Sign up

Export Citation Format

Share Document