scholarly journals Investigation of Dynamic, Mechanical, and Thermal Properties of Calotropis procera Particle-Reinforced PLA Biocomposites

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
K. Yoganandam ◽  
Vigneshwaran Shanmugam ◽  
A. Vasudevan ◽  
D. Vinodh ◽  
N. Nagaprasad ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Heat Dissipation ◽  
Melt Flow Index ◽  
Calotropis Procera ◽  
Flow Index ◽  
Injection Molding Process ◽  
Mechanical And Thermal Properties ◽  
Molding Process ◽  
Weight Percentage ◽  
Dynamic Mechanical

The thermal behavior of the biodegradable Calotropis procera (CP) particle-reinforced polylactic acid (PLA) biocomposites was investigated. The injection molding process was used to make the composites, and the CP particle weight percentage was varied during the process (0%, 5%, 10%, 15%, and 20%). The melt flow index, heat deflection temperature, Vicat softening point, and the thermal properties of the composites were determined using dynamic mechanical testing. The results were analyzed and compared to the thermal properties of the neat PLA. The results revealed the increase in thermal stability of the PLA due to the addition of CP particles. The CP particles aided in the restriction of polymer mobility, which elevated the glass transition temperature of the composite. Incorporating CP particles in the PLA can increase the PLA/CP composite utilization in heat dissipation applications.

scholarly journals Effect of the Compounding Conditions of Polyamide 6, Carbon Fiber, and Al2O3 on the Mechanical and Thermal Properties of the Composite Polymer

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3047 ◽  
Author(s):  
Young Shin Kim ◽  
Jae Kyung Kim ◽  
Euy Sik Jeon
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Injection Molding ◽  
Mechanical Strength ◽  
Melt Flow Index ◽  
Polyamide 6 ◽  
Extrusion Process ◽  
Flow Index ◽  
Process Conditions ◽  
Mechanical And Thermal Properties

Among the composite manufacturing methods, injection molding has higher time efficiency and improved processability. The production of composites via injection molding requires a pre-process to mix and pelletize the matrix polymer and reinforcement material. Herein, we studied the effect of extrusion process conditions for making pellets on the mechanical and thermal properties provided by injection molding. Polyamide 6 (PA6) was used as the base, and composites were produced by blending carbon fibers and Al2O3 as the filler. To determine the optimum blending ratio, the mechanical properties, thermal conductivity, and melt flow index (MI) were measured at various blending ratios. With this optimum blending ratio, pellets were produced by changing the temperature and RPM conditions, which are major process variables during compounding. Samples were fabricated by applying the same injection conditions, and the mechanical strength, MI values, and thermal properties were measured. The mechanical strength increased slightly as the temperature and RPM increased, and the MI and thermal conductivity also increased. The results of this study can be used as a basis for specifying the conditions of the mixing and compounding process such that the desired mechanical and thermal properties are obtained.

Mechanical and thermal characterization of polypropylene-reinforced nanocrystalline cellulose nanocomposites

2020 ◽  
pp. 089270572092512
Author(s):  
Mohammad Y Al-Haik ◽  
Saud Aldajah ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Stability ◽  
Thermal Properties ◽  
Thermal Characterization ◽  
Nanocrystalline Cellulose ◽  
Injection Molding Process ◽  
Mechanical And Thermal Properties ◽  
Molding Process ◽  
Point Bend ◽  
Cellulose Nanocomposites

This article addresses the effect of nanocrystalline cellulose (NCC) on the mechanical and thermal properties of polypropylene (PP). A new approach was adopted to produce mechanically improved and thermally stable PP-NCC nanocomposite. This approach involved producing optimized PP-NCC nanocomposite by adding NCC nanoparticles to PP matrix at different concentrations by means of injection molding process. The aim of this work was to find the optimum NCC concentration to enhance the mechanical and thermal properties of the PP matrix. The mechanical and thermal behavior of PP-NCC nanocomposite was studied by performing three-point bend, nanoindentation, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), scanning electron microscope (SEM), and Fourier transform infrared (FTIR) spectroscopy tests. The results showed that the mechanical properties of strength, modulus, and hardness of the nanocomposites increased with the addition of NCC by 6.5%, 19%, and 150%, respectively. DSC results showed that the addition of NCC to PP does not affect the thermal stability (melting temperature). However, TGA showed that upon inclusion of NCC nanoparticles, the thermal stability of the samples improved compared to pure PP except for the 5% added NCC. This is attributed to the presence of NCC rod-like particles that dissipated heat by generating tortuous paths, as depicted in the SEM results and verified by FTIR results.

Thermal and mechanical properties of glass fibre reinforced polyphenylene ether/polystyrene/nylon-6 ternary blends

2020 ◽  
pp. 096739112094949
Author(s):  
Prakash Hadimani ◽  
HN Narasimha Murthy ◽  
Rajalakshmi Mudbidre
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Maleic Anhydride ◽  
Injection Moulding ◽  
Melt Flow Index ◽  
Nylon 6 ◽  
Flow Index ◽  
Mechanical And Thermal Properties ◽  
Ternary Blends ◽  
Compression Moulding

This paper deals with fabrication and characterization of unique polyphenylene ether/polystyrene/nylon-6/glass composites. Compounding of ternary blends with glass fibres was performed using twin screw co-rotating extruder. Test specimens were fabricated by compression moulding and injection moulding. Effect of maleic anhydride, fibre type (chopped and long), fibre content (30 wt. % and 40 wt. %) and fabrication method (compression moulding and injection moulding) on mechanical and thermal properties was studied. Maleic anhydride negatively influenced mechanical and thermal properties. Composites with 40 wt. % chopped fibres showed superior mechanical strength and those with 30 wt. % long fibres showed superior thermal properties, tensile and flexural moduli. Injection moulded specimens exhibited superior mechanical and thermal properties. The composites were studied for moisture content, density, melt flow index, glass transition temperature, thermal degradation temperature and mechanical properties. Interfacial strength was examined using scanning electron microscopy.

Physical and mechanical performance of bentonite and barite loaded low density polyethylene composites: Influence of surface silanization of minerals

2020 ◽  
Vol 54 (28) ◽  
pp. 4359-4368 ◽  
Author(s):  
Hesham Elkawash ◽  
Seha Tirkes ◽  
Firat Hacioglu ◽  
Umit Tayfun
Keyword(s):  
Mechanical Performance ◽  
Water Repellency ◽  
Surface Characteristics ◽  
Melt Flow Index ◽  
Low Density Polyethylene ◽  
Flow Index ◽  
Injection Molding Process ◽  
Low Density ◽  
Melt Flow ◽  
Molding Process

In this study, two kinds of mineral fillers, bentonite (BNT) and barite (BRT), were incorporated into low density polyethylene (LDPE) by extrusion process. Silane treatment was applied to BRT and BNT surfaces in order to increase their compatibility with LDPE matrix. Surface characteristics of fillers were examined by Fourier transformed infrared spectroscopy (FTIR). LDPE-based composites were prepared at a constant concentration of 10%wt for each additives. Test samples were shaped by injection molding process. Mechanical, thermo-mechanical, water repellency, melt-flow and morphological characterizations of LDPE and its composites were performed by tensile and impact tests, dynamic mechanical analysis (DMA), water absorption test, melt flow index (MFI) measurements and scanning electron microscopy (SEM) technique, respectively. Test results showed that surface treatments led to increase for final properties of composites since they promoted to stronger adhesion between minerals and LDPE matrix compared to untreated ones. Tensile and impact strength values, storage modulus and glass transition temperature of LDPE were improved by inclusion of silane treated minerals. BRT and BNT additions caused no remarkable changes with regard to MFI of LDPE. Additionally, silane modified mineral filled composites exhibited remarkable water resistance behavior. According to SEM analysis of composites, silane treated BNT and BRT containing samples displayed homogeneous dispersions into LDPE phase whereas debondings were observed for untreated BNT and BRT filled composites due to their weak adhesion to polymer matrix.

Effect of Algerian Halloysite on the Mechanical and Thermal Properties of Starch-Grafted-Polyethylene Nanocomposites

2018 ◽  
Vol 762 ◽  
pp. 192-196 ◽  
Author(s):  
Walid Fermas ◽  
Remo Merijs Meri ◽  
Mustapha Kaci ◽  
Janis Zicans
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Melt Flow Index ◽  
Halloysite Nanotubes ◽  
Polymer Chains ◽  
Flow Index ◽  
Mechanical And Thermal Properties ◽  
Melt Compounding

This paper deals with the characterization of the physico-mechanical properties of starch-grafted-polyethylene (Starch-g-PE)/unmodified Algerian halloysite nanotubes (HNT) nanocomposites prepared by melt compounding. The nanoclay was incorporated at various filler contents, i.e., 1.5, 3 and 5 wt%. Rheological and tensile properties of the nanocomposites were evaluated by different techniques and the results obtained are compared with those of virgin Starch-g-PE matrix. The study shows a decrease in melt flow index (MFI) values upon increasing the HNT content, which indicates a restriction in the polymer chains mobility due to the confinement effect of HNT. Further, a tensile strength is also improved.

Characterization of microwave-treated oil palm empty fruit bunch/glass fibre/polypropylene composites

2015 ◽  
Vol 30 (7) ◽  
pp. 986-1002 ◽  
Author(s):  
MR Islam ◽  
A Gupta ◽  
M Rivai ◽  
MDH Beg
Keyword(s):  
Glass Fibre ◽  
Oil Palm ◽  
Melt Flow Index ◽  
Flow Index ◽  
Mechanical And Thermal Properties ◽  
Empty Fruit Bunch ◽  
Scanning Calorimetry ◽  
Fixed Temperature ◽  
Polypropylene Composites ◽  
Degradation Temperature

Composites were prepared from recycled polypropylene (RPP), oil palm empty fruit bunch (EFB) and/or glass fibre (GF) using extrusion and injection moulding techniques. Two types of maleic anhydride-grafted polypropylene such as Polybond 3200 and Fusabond P 613 were used to improve the interfacial adhesion between fibres and matrix. The EFB: GF ratio was fixed as 70:30 and fibre loading was considered as 40 wt%. Microwave was used to treat the EFB fibre, which was soaked in a fixed mass concentration (12.5%) of alkali solution at different temperatures (70, 80 and 90°C) for a fixed period of time (60 min) and for different times (60, 90 and 120 min) at a fixed temperature (90°C). A magnetron controller was developed to control the time and temperature accurately for the treatment of fibre. Various characterization techniques such as density, melt flow index, tensile, Izod impact, flexural, field-emission scanning electron microscopy and water uptake testing were performed for the composites. Besides, thermogravimetric analysis and differential scanning calorimetry were also used to evaluate the thermal and crystalline properties of the composites, respectively. Result analyses revealed that microwave-treated fibre-based composites showed improved mechanical and thermal properties. EFB fibres treated at 90°C for 90 min were found to be suitable for better reinforcement into the composite in terms of mechanical, thermal and crystalline properties. Moreover, onset degradation temperature and water absorption properties were also found to be changed apparently due to treatment.

Sign in / Sign up

Export Citation Format

Share Document