scholarly journals Wideband Slot Array Antenna Fed by Gap Waveguide with Right-Handed Circular Polarization and High Gain

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Pejman Mahmoudi Kanesbi ◽  
Nasrin Amiri
Keyword(s):  
Circular Polarization ◽  
Millimeter Wave ◽  
Axial Ratio ◽  
High Gain ◽  
Array Antenna ◽  
Impedance Bandwidth ◽  
Frequency Range ◽  
Circularly Polarized ◽  
Metal Layers ◽  
Final Array

A wideband and high-gain circularly polarized (CP) 16 × 16 array antenna based on gap waveguide technology is presented for millimeter-wave applications at 28 GHz frequency range. Four cavity-backed slots with linear polarized (LP) radiation are used as the subarray. CP is obtained by a 4 × 4 sequential feeding network which is also expanded to achieve high gain. The feeding network of the final array antenna consists of two layers based on the ridge gap waveguide (RGW), and it has four unconnected metal layers. It is shown by simulation that the proposed antenna has 20.5% impedance bandwidth over 25.8–31.7 GHz and 3 dB axial ratio bandwidth near 10% over 27.2–30 GHz. In addition, the maximum gain value for this antenna is 31.6 dBi at a frequency of 29 GHz, which shows good performance compared to other structures.

scholarly journals Metallic Reflector-Based X-Band Circularly Polarized Hollow Dielectric Resonator Antenna for High Gain in UWB Applications

2021 ◽  
Author(s):  
SACHIN KUMAR YADAV ◽  
Amanpreet Kaur ◽  
Rajesh Khanna
Keyword(s):  
Circular Polarization ◽  
Dielectric Resonator ◽  
Near Field ◽  
Axial Ratio ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Circularly Polarized ◽  
X Band ◽  
Peak Gain

Abstract A circularly polarized hollow dielectric resonator antenna (CPHDRA) is designed for X-band applications. Rectangular dielectric resonator (RDR) is used as a radiator element, fed by a quarter-wave transformer (QWT) feedline. By performance of the RDR antenna, an air cylindrical rod structure is extracted from RDR to enhance the gain and impedance bandwidth. Two parasitic strips are placed on the top of the RDR to achieve circular polarization with reported ≤ 3-dB axial ratio (AR) bandwidth for X-band applications. In this article, UWB antenna covers range from 2.74 to 10.4GHz by using asymmetrical defective ground structure (DGS). In near field of the dielectric resonator, three different radiating modes namely HE11δ, HE21δ, HE23δ, and HE32δ are at 4.4, 6, 8.8, and 9.9 GHz. For the generation of circular polarization (CP), two orthogonal modes are generated at 8.8 and 9.9 GHz as per XZ and YZ planes. It has reported 23.8 % (8 to 10.1 GHz) of 3-dB AR bandwidth. The simulated and measured impedance bandwidths are 118.46 % and 121.12 % along with a peak gain of 6.55 dB without the use of a metallic reflector. By using a metallic reflector suspended in the bottom side of the substrate with a distance of 13.1mm is reported along with the peak gain of 9.8 dBi.

A Broadband Circularly Polarized Cross-slotted Patch Antenna with Horizontal Meandered Strip (HMS)

Frequenz ◽  
2020 ◽  
Vol 74 (5-6) ◽  
pp. 191-199
Author(s):  
M. K. Verma ◽  
Binod K. Kanaujia ◽  
J. P. Saini ◽  
Padam S. Saini
Keyword(s):  
Circular Polarization ◽  
Patch Antenna ◽  
Impedance Matching ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Radiation Patterns ◽  
Circularly Polarized ◽  
Feeding Technique

AbstractA broadband circularly polarized slotted square patch antenna with horizontal meandered strip (HMS) is presented and studied. The HMS feeding technique provides the good impedance matching and broadside symmetrical radiation patterns. A set of cross asymmetrical slots are etched on the radiating patch to realize the circular polarization. An electrically small stub is added on the edge of the antenna for further improvement in performance. Measured 10-dB impedance bandwidth (IBW) and 3-dB axial ratio bandwidth (ARBW) of the proposed antenna are 32.31 % (3.14–4.35 GHz) and 20.91 % (3.34–4.12 GHz), respectively. The gain of the antenna is varied from 3.5 to 4.86dBi within 3-dB ARBW. Measured results matched well with the simulated results.

ANALYSIS PERFORMANCE OF SINGLY-FED CIRCULARLY POLARIZED MICROSTRIP ANTENNA FOR WIRELESS COMMUNICATION

2016 ◽  
Vol 78 (5-9) ◽  
Author(s):  
Muhammad Fauzan Edy Purnomo ◽  
Hadi Suyono ◽  
Panca Mudjirahardjo ◽  
Rini Nur Hasanah
Keyword(s):  
Wireless Communication ◽  
Circular Polarization ◽  
Microstrip Antenna ◽  
Axial Ratio ◽  
Microstrip Antennas ◽  
Impedance Bandwidth ◽  
Antenna Structure ◽  
Circularly Polarized ◽  
Large Bandwidth ◽  
Doubly Fed

The circularly polarized (CP) microstrip antennas, both of singly- and doubly-fed types, possess inherent limitation in gain, impedance and axial-ratio bandwidths. These limitations are caused mainly by the natural resonance of the patch antenna which has a high unloaded Q-factor and the frequency-dependent excitation of two degenerative modes (TM01 and TM10) when using a single feed. Many applications which require circular polarization, large bandwidth, and good performance, especially in the field of wireless communication, are still difficult to be designed by using antenna software. Some consideration to take will include the application target and design specification, the materials to be used, and the method to choose (formula, numerical analysis, etc). This paper explains and analyzes the singly-fed microstrip antenna with circular polarization and large bandwidth. This singly-fed type of microstrip antenna provides certain advantage of requiring no external circular polarizer, e.g. the 900 hybrid, as it only needs to apply some perturbation or modification to a patch radiator with a standard geometry. The design of CP and large-bandwidth microstrip antenna is done gradually, by firstly truncating one tip, then truncating the whole three tips, and finally modifying it into a pentagonal patch structure and adding an air-gap to obtain larger bandwidths of impedance, gain and axial ratio. The last one antenna structure results in a novelty because it is a rare design of antenna which includes all types of bandwidth (impedance, gain, and axial ratio) being simultaneously larger than the origin antenna. The resulted characteristic performance of the 1-tip (one-tip) antenna shows respectively 1.9% of impedance bandwidth, 3.1% of gain bandwidth, and 0.45% of axial-ratio bandwidth. For the 3-tip (three-tip) step, the resulted bandwidths of respectively impedance, gain, and axial ratio are 1.7%, 3.3% and 0.5%. The pentagonal structure resulted in the bandwith values of 15.67%, 52.16% and 4.11% respectively for impedance, gain, and axial ratio. 

Reconfigurable circularly polarized capacitive coupled microstrip antenna

2016 ◽  
Vol 9 (4) ◽  
pp. 843-850 ◽  
Author(s):  
Dinesh Kumar Singh ◽  
Binod Kumar Kanaujia ◽  
Santanu Dwari ◽  
Ganga Prasad Pandey ◽  
Sandeep Kumar
Keyword(s):  
Circular Polarization ◽  
Microstrip Antenna ◽  
Axial Ratio ◽  
Dual Band ◽  
Single Frequency ◽  
Impedance Bandwidth ◽  
Pin Diode ◽  
Dual Frequency ◽  
Pin Diodes ◽  
Circularly Polarized

The design and measurement of reconfigurable circularly polarized capacitive fed microstrip antenna are presented. Small isosceles right angle triangular sections are removed from diagonally opposite corners for the generation of circular polarization (CP) of axial ratio bandwidth of 11.1%. Horizontal slits of different lengths are inserted at the edges of the truncated patch to provide the dual-band CP and by switching PIN diodes across the slits ON and OFF, reconfigurable circularly polarized antenna is realized. The antenna shows dual-band behavior with reconfigurable CP. In order to enhance the operation bandwidth of the antenna, an inclined slot was embedded on the patch along with PIN diodes across the horizontal slits. This proposed antenna gave an impedance bandwidth of 66.61% (ON state) ranging from 4.42 to 8.80 GHz and 68.42% (OFF state) ranging from 4.12 to 8.91 GHz and exhibits dual-frequency CP with PIN diode in OFF state and single-frequency CP with PIN diode in ON state with good axial ratio bandwidth. The axial ratio bandwidth of 4.42, 2.35, and 2.72% is obtained from the antenna. The antenna has a similar radiation pattern in all the three different CP bands and almost constant gain within the bands of CP operation.

scholarly journals A Millimeter-Wave Wideband Circularly Polarized Planar Spiral Antenna Array with Unequal Amplitude Feeding Network

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Huakang Chen ◽  
Yu Shao ◽  
Zhangjian He ◽  
Changhong Zhang ◽  
Zhizhong Zhang
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Axial Ratio ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Archimedean Spiral ◽  
Circularly Polarized

A 2 × 2 wideband circularly polarized (CP) antenna array operating at millimeter wave (mmWave) band is presented. The array element is a wideband CP Archimedean spiral radiator with special-shaped ring slot. The elements are fed by an unequal amplitude (UA) feeding network based on a microstrip line (MSL) power divider. The side lobe level is improved by this UA feeding network. In addition, a cross slot is employed to isolate the elements for decoupling. A prototype is fabricated, and the measured results show that the proposed array achieves an impedance bandwidth (IBW) of 6.31 GHz (22.5% referring to 28 GHz) and an axial ratio bandwidth (ARBW) of 7.32 GHz (26.1% referring to 28 GHz). The peak gain of the proposed array is 11.3 dBic, and the gain is greater than 9.3 dBic within the whole desired band (from 25 GHz to 31 GHz). The proposed array consists of only one substrate layer and can be built by the conventional printed circuit board technology. Attributed to the characteristics of wide bandwidth, simple structure, low profile, and low cost, the proposed antenna array has a great potential in mmWave wireless communications.

scholarly journals High-Gain Circularly-Polarized Elliptically-Annular Antenna-Array with Reduced Side-Lobe Level

2020 ◽  
Vol 9 (4) ◽  
pp. 2319-2325
Keyword(s):  
Circular Polarization ◽  
Antenna Array ◽  
Satellite Communication ◽  
Axial Ratio ◽  
Side Lobe ◽  
High Gain ◽  
Side Lobe Level ◽  
Single Element ◽  
Circularly Polarized ◽  
Gain Enhancement

A single feed microstrip patch elliptically annular antenna array has been proposed for high gain circularly polarized (CP) radiation. An array of elliptically annular patches antenna resonates at a frequency of 3.77 GHz which can be used in satellite communication and radar application. A corporate feed network with quarter-wave transformer has been used for uniform excitation of all the array elements. Thus a good circular polarization is obtained by using a single feed with enhanced gain 15.62 dB compared to single patch. The radiation pattern, axial ratio and input impedance of the proposed elliptically annular antenna array is compared with single element elliptically annular antenna. A substantial gain enhancement with low side lobe level (SLL) is observed keeping circular polarization intact. Further, simulated and measured results of the proposed antenna array have been compared and found that axial ratio and gain are in good agreement.

scholarly journals Circularly Polarized Triband Printed Quasi-Yagi Antenna for Millimeter-Wave Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Dalia M. Elsheakh ◽  
Magdy F. Iskander
Keyword(s):  
Circular Polarization ◽  
Printed Circuit Board ◽  
Ground Plane ◽  
Axial Ratio ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
60 Ghz ◽  
Antenna Structure ◽  
Circularly Polarized ◽  
Yagi Antenna

This paper describes the design and development of a triband with circularly polarized quasi-Yagi antenna for ka-band and short range wireless communications applications. The proposed antenna consists of an integrated balun-fed printed dipole, parasitic folded dipole and a short strip, and a modified ground plane. The antenna structure, together with the parasitic elements, is designed to achieve circular polarization and triband operating at resonant frequencies of 13.5 GHz, 30 GHz, and 60 GHz. Antenna design was first simulated using HFSS ver.14, and the obtained results were compared with experimental measurements on a prototype developed on a single printed circuit board. Achieved characteristics include −10 dB impedance bandwidth at the desired bands, circular polarization axial ratioAR<3 dB, front to back ratio of 6 dB, gain value of about 4 dBi, and average radiation efficiency of 60%. The paper includes comparison between simulation and experimental results.

scholarly journals Series-Fed Microstrip Array Antenna with Circular Polarization

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Tuan-Yung Han
Keyword(s):  
Circular Polarization ◽  
Simulated Data ◽  
Axial Ratio ◽  
Array Element ◽  
Array Antenna ◽  
Antenna Design ◽  
Circularly Polarized ◽  
Feed Network ◽  
Microstrip Array ◽  
Microstrip Array Antenna

This study proposes a novel 2 × 2 array antenna design with broadband and circularly-polarized (CP) operation. The proposed design uses a simple series-fed network to increase the CP bandwidth without requiring one-by-one adjustment of each array element or a complex feed network. Selecting the appropriate spacing between each array element allows the proposed array antenna to generate CP radiation with a low axial ratio. Experimental results based on a prototype show that this 2 × 2 microstrip array antenna achieves a wide 3 dB axial ratio bandwidth of more than 10%. Simulated data are also provided to confirm the measured results.

scholarly journals Dual Circularly Polarized Planar Four-Port MIMO Antenna with Wide Axial-Ratio Bandwidth

Sensors ◽  
2020 ◽  
Vol 20 (19) ◽  
pp. 5610
Author(s):  
Sachin Kumar ◽  
Gwan Hui Lee ◽  
Dong Hwi Kim ◽  
Hyun Chul Choi ◽  
Kang Wook Kim
Keyword(s):  
Circular Polarization ◽  
Multiple Input Multiple Output ◽  
Vector Current ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Mimo Antenna ◽  
Left Hand ◽  
Input Multiple Output ◽  
Polarization Mechanism

A broadband compact-sized planar four-port multiple-input–multiple-output (MIMO) antenna with polarization diversity is presented. The proposed dual circularly polarized (CP) MIMO antenna consists of four G-shaped monopole elements, two of which are left-hand CP and the other two are right-hand CP. A vertical line strip in the G-shaped radiating element acts in balancing the vertical and horizontal electric field components to obtain 90° phase difference between them for circular polarization. Also, an I-shaped strip is incorporated between the ground planes of the G-shaped antenna elements to obtain equal voltage level in the proposed MIMO configuration. The dual circular polarization mechanism of the proposed MIMO/diversity antenna is analysed from the vector current distributions. The impedance bandwidth (S11 ≤ –10 dB) of the MIMO antenna is 105.9% (4–13 GHz) and the 3 dB axial ratio bandwidth (ARBW) is 67.7% (4.2–8.5 GHz), which is suitable for C-band applications. The overall size of the MIMO antenna is 70 × 68 × 1.6 mm3, and the minimum isolation between the resonating elements is 18 dB. The envelope correlation coefficient is less than 0.25, and the peak gain within the resonating band is 6.4 dBi.

scholarly journals X-Slotted circularly polarized antenna with parasitic patches

2017 ◽  
Vol 7 (1.1) ◽  
pp. 534
Author(s):  
B T P Madhav ◽  
Habibulla Khan ◽  
B Sri Harsha ◽  
P Sai Kumar ◽  
M Lavanya ◽  
...  
Keyword(s):  
Comparative Analysis ◽  
Circular Polarization ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Circularly Polarized

A compact circularly polarized antenna having x-slot in the parasitic patches have been proposed in this article. Four driven patches which are capacitively loaded with the help of the feeding loop and four parasitic patches which generate circular polarization because of the sequentially rotated structures are noticed in the proposed modal. With combination of the CP mode with the feeding loop we can observe the broadened axial ratio bandwidth. Comparative analysis has been observed for each side facing driven elements and side and edge facing parasitic elements with X-slot have been observed. The proposed antenna works at the bands of 5.04-5.83GHz and 6.34-6. 81GHz which works for WLAN application. The proposed modal and its iterations have been analyzed using ANSYS EM Software. The results show an enhanced impedance bandwidth of 22 percent and axial ratio bandwidth of over 15percent has been noticed in the proposed modal. A constant gain has been noticed all over the analyzed modals.

Sign in / Sign up

Export Citation Format

Share Document