scholarly journals The Study of Three-Dimensional Granular Stream Flowing through the Test Hopper-Shaped Target

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Chengwen Qiang ◽  
Weifeng Yang ◽  
Long Li ◽  
Fei Wang ◽  
Weiping Deng ◽  
...  
Keyword(s):  
Flow Rate ◽  
Inclination Angle ◽  
Granular Flow ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Rotation Frequency ◽  
Gravity Flow ◽  
Screw Conveyor ◽  
Dense Flow ◽  
Elevated Frequency

The experiments are carried out in a three-dimensional channel with a screw conveyor, which plays the role of granular drives for the granular flow system and determines the injection of granular in the test target section. The jam-to-dense transition of granular flow is studied with the different inclination angle. The results show that, with a fixed diameter of hopper orifice and initial filling position, there is a change from jam to dense when the inclination angle larger than 22°. Variation of the flow rate with elevated frequency of the screw conveyor is further studied. The flow pattern is changed from dilute to dense with increasing rotation frequency of the screw rod. When the rotation frequency is larger than 5 Hz, the flow is dense. The dynamic balance of the interface between dilute to dense granular is observed in the main target section. We further research the dynamic interface by measuring the highest and lowest location with time and also simulate the gravity flow rate and screw conveyor flow rate with EDEM. From the results, we find that the interface between dilute flow and dense flow is influenced by the combined action of crew conveyor flow and dense gravity flow.

Dilute-to-dense flow transition and flow-rate behavior of lateral bifurcated granular flow

2021 ◽  
Vol 383 ◽  
pp. 536-541
Author(s):  
Xiaoyan Zhou ◽  
Shikun Liu ◽  
Zihan Zhao ◽  
Xin Li ◽  
Changhao Li ◽  
...  
Keyword(s):  
Flow Rate ◽  
Granular Flow ◽  
Flow Transition ◽  
Dense Flow ◽  
Rate Behavior

Experiment Study and Optimization of Merging Granular Flow

2014 ◽  
Vol 487 ◽  
pp. 400-403 ◽  
Author(s):  
Guo Cheng Yang ◽  
Qi Yi Liu ◽  
Mao Bin Hu ◽  
Rui Jiang ◽  
Qing Song Wu ◽  
...  
Keyword(s):  
Flow Pattern ◽  
Flow Rate ◽  
Granular Flow ◽  
Important Process ◽  
Experiment Study ◽  
Chute Flow ◽  
Dense Flow

Granular flow is an important process in industry, agriculture and mining. This paper studies the flow pattern and optimization of two channels of granular chute flow merging into one channel. Experiment shows that the flow pattern in each channel can be dilute flow, shock or dense flow. Base on the discovery, one can optimize the flow rate in this system.

GRANULAR FLOW IN THE PRESENCE OF AN ELECTRIC FIELD

2002 ◽  
Vol 16 (17n18) ◽  
pp. 2536-2541
Author(s):  
KUNQUAN LU ◽  
WEI CHEN ◽  
MEIYING HOU ◽  
ZEHUI JIAN
Keyword(s):  
Electric Field ◽  
Flow Rate ◽  
Granular Flow ◽  
Applied Field ◽  
Critical Value ◽  
Vertical Pipe ◽  
Initial State ◽  
Dense Flow ◽  
Two Phases ◽  
Controlled Flow

The granular flow in a vertical pipe in the presence of electric field E is studied. Depending upon its initial state and the applied field voltage the controlled flow rate remains in two phases, dilute flow or dense flow. For dilute flow, the electric field has no effect on the flow rate until V reaches a critical value V 1. At V = V 1, the flow rate drops abruptly and a transition of the particulate from dilute to dense flow occurs. For dense flow, the flow rate decreases monotonically with increasing V. A two-dimensional computer simulation has been done and the results agree qualitatively well with the experimental measurements.

scholarly journals Avalanche simulation with SAMOS

2004 ◽  
Vol 38 ◽  
pp. 393-398 ◽  
Author(s):  
Peter Sampl ◽  
Thomas Zwinger
Keyword(s):  
Granular Flow ◽  
Flow Model ◽  
Three Dimensional ◽  
Coupled Model ◽  
Powder Flow ◽  
Transition Model ◽  
Snow Layer ◽  
Hazard Zoning ◽  
Order Of Magnitude ◽  
Dense Flow

AbstractDry snow avalanches consist of two distinct layers. A dense-flow layer is superposed by a powder-snow layer, a cloud of relatively small ice particles suspended in air. The density of this suspension is one order of magnitude smaller than that of the dense flow. A simulation model for dry avalanches has been developed, based on separate sub-models for the two layers. The sub-models are coupled by an additional transition model, describing the exchange of mass and momentum between the layers. The fundamentals of the two-dimensional granular flow model for the dense flow and of the three-dimensional turbulent mixture model for the powder flow are presented. Results of the complete coupled model, SAMOS (Snow Avalanche MOdelling and Simulation), applied to observed catastrophic avalanche events, are discussed, and the prediction of powder-snow pressures acting on a tunnel bridge is briefly described. SAMOS is used routinely for hazard zoning at the Austrian Federal Service for Torrent and Avalanche Control.

scholarly journals A Numerical Study of Sub-Millisecond Integrated Mix-and-Inject Microfluidic Devices for Sample Delivery at Synchrotron and XFELs

2021 ◽  
Vol 11 (8) ◽  
pp. 3404
Author(s):  
Majid Hejazian ◽  
Eugeniu Balaur ◽  
Brian Abbey
Keyword(s):  
Molecular Dynamics ◽  
Flow Rate ◽  
Numerical Study ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Liquid Jets ◽  
Mixing Efficiency ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
Time Required

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

scholarly journals Energy Loss in Steep Open Channels with Step-Pools

Water ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 72
Author(s):  
Suresh Kumar Thappeta ◽  
S. Murty Bhallamudi ◽  
Venu Chandra ◽  
Peter Fiener ◽  
Abul Basar M. Baki
Keyword(s):  
Energy Loss ◽  
Flow Rate ◽  
Recirculation Zone ◽  
Three Dimensional ◽  
Nonlinear Function ◽  
Open Channels ◽  
Geometrical Parameters ◽  
Transition Flow ◽  
Cumulative Energy ◽  
Zone Velocity

Three-dimensional numerical simulations were performed for different flow rates and various geometrical parameters of step-pools in steep open channels to gain insight into the occurrence of energy loss and its dependence on the flow structure. For a given channel with step-pools, energy loss varied only marginally with increasing flow rate in the nappe and transition flow regimes, while it increased in the skimming regime. Energy loss is positively correlated with the size of the recirculation zone, velocity in the recirculation zone and the vorticity. For the same flow rate, energy loss increased by 31.6% when the horizontal face inclination increased from 2° to 10°, while it decreased by 58.6% when the vertical face inclination increased from 40° to 70°. In a channel with several step-pools, cumulative energy loss is linearly related to the number of step-pools, for nappe and transition flows. However, it is a nonlinear function for skimming flows.

Thermal Characterization of Interlayer Microfluidic Cooling of Three-Dimensional Integrated Circuits With Nonuniform Heat Flux

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Yoon Jo Kim ◽  
Yogendra K. Joshi ◽  
Andrei G. Fedorov ◽  
Young-Joon Lee ◽  
Sung-Kyu Lim
Keyword(s):  
Integrated Circuits ◽  
Mass Flow Rate ◽  
Thermal Management ◽  
Mass Flow ◽  
Flow Rate ◽  
Single Phase ◽  
Hot Spot ◽  
Three Dimensional ◽  
Two Phase ◽  
Two Phase Cooling

It is now widely recognized that the three-dimensional (3D) system integration is a key enabling technology to achieve the performance needs of future microprocessor integrated circuits (ICs). To provide modular thermal management in 3D-stacked ICs, the interlayer microfluidic cooling scheme is adopted and analyzed in this study focusing on a single cooling layer performance. The effects of cooling mode (single-phase versus phase-change) and stack/layer geometry on thermal management performance are quantitatively analyzed, and implications on the through-silicon-via scaling and electrical interconnect congestion are discussed. Also, the thermal and hydraulic performance of several two-phase refrigerants is discussed in comparison with single-phase cooling. The results show that the large internal pressure and the pumping pressure drop are significant limiting factors, along with significant mass flow rate maldistribution due to the presence of hot-spots. Nevertheless, two-phase cooling using R123 and R245ca refrigerants yields superior performance to single-phase cooling for the hot-spot fluxes approaching ∼300 W/cm2. In general, a hybrid cooling scheme with a dedicated approach to the hot-spot thermal management should greatly improve the two-phase cooling system performance and reliability by enabling a cooling-load-matched thermal design and by suppressing the mass flow rate maldistribution within the cooling layer.

scholarly journals Porous PLAs with Controllable Density by FDM 3D Printing and Chemical Foaming Agent

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 866
Author(s):  
A. R. Damanpack ◽  
André Sousa ◽  
M. Bodaghi
Keyword(s):  
3D Printing ◽  
Flow Rate ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Layer By Layer ◽  
Printing Technology ◽  
Material Density ◽  
Foaming Agent ◽  
3D Printing Technology ◽  
Fabrication Parameters

This paper shows how fused decomposition modeling (FDM), as a three-dimensional (3D) printing technology, can engineer lightweight porous foams with controllable density. The tactic is based on the 3D printing of Poly Lactic Acid filaments with a chemical blowing agent, as well as experiments to explore how FDM parameters can control material density. Foam porosity is investigated in terms of fabrication parameters such as printing temperature and flow rate, which affect the size of bubbles produced during the layer-by-layer fabrication process. It is experimentally shown that printing temperature and flow rate have significant effects on the bubbles’ size, micro-scale material connections, stiffness and strength. An analytical equation is introduced to accurately simulate the experimental results on flow rate, density, and mechanical properties in terms of printing temperature. Due to the absence of a similar concept, mathematical model and results in the specialized literature, this paper is likely to advance the state-of-the-art lightweight foams with controllable porosity and density fabricated by FDM 3D printing technology.

scholarly journals A Three-Dimensional Shock Loss Model Applied to an Aft-Swept, Transonic Compressor Rotor

1996 ◽  
Author(s):  
Steven L. Puterbaugh ◽  
William W. Copenhaver ◽  
Chunill Hah ◽  
Arthur J. Wennerstrom
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Numerical Results ◽  
Design Flow ◽  
Design System ◽  
Loss Model ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Shock Loss

An analysis of the effectiveness of a three-dimensional shock loss model used in transonic compressor rotor design is presented. The model was used during the design of an aft-swept, transonic compressor rotor. The demonstrated performance of the swept rotor, in combination with numerical results, is used to determine the strengths and weaknesses of the model. The numerical results were obtained from a fully three-dimensional Navier-Stokes solver. The shock loss model was developed to account for the benefit gained with three-dimensional shock sweep. Comparisons with the experimental and numerical results demonstrated that shock loss reductions predicted by the model due to the swept shock induced by the swept leading edge of the rotor were exceeded. However, near the tip the loss model under-predicts the loss because the shock geometry assumed by the model remains swept in this region while the numerical results show a more normal shock orientation. The design methods and the demonstrated performance of the swept rotor is also presented. Comparisons are made between the design intent and measured performance parameters. The aft-swept rotor was designed using an inviscid axisymmetric streamline curvature design system utilizing arbitrary airfoil blading geometry. The design goal specific flow rate was 214.7 kg/sec/m2 (43.98 lbm/sec/ft2), the design pressure ratio goal was 2.042, and the predicted design point efficiency was 94.0. The rotor tip sped was 457.2 m/sec (1500 ft/sec). The design flow rate was achieved while the pressure ratio fell short by 0.07. Efficiency was 3 points below prediction, though at a very high 91 percent. At this operating condition the stall margin was 11 percent.

Sign in / Sign up

Export Citation Format

Share Document