scholarly journals Nonlinear Creep Behavior and Viscoelastic-Plastic Constitutive Model of Rock-Concrete Composite Mass

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Yang Liu ◽  
Da Huang ◽  
Baoyun Zhao ◽  
Chen Wang ◽  
Duofeng Cen
Keyword(s):  
Mechanical Properties ◽  
Creep Rate ◽  
Composite Structures ◽  
Testing Machine ◽  
Confining Pressure ◽  
Creep Process ◽  
Nonlinear Creep ◽  
Creep Tests ◽  
Triaxial Compressive Strength ◽  
Confining Pressures

The joint force deformation of rock-concrete composite structures is different from that of simple rock specimens or concrete specimens, such as the tunnel surrounding rock-lining concrete, dam foundations, and concrete. In order to study the creep mechanical properties of rock-concrete composite structures under long-duration load, the TFD-2000 microcomputer servo triaxial creep testing machine is used to carry out step loading creep tests on rock-concrete composite specimens (hereinafter referred to as composite specimens) under different confining pressures (including the confining pressures σ3 = 0 MPa). The creep test results show that, under the same confining pressure, when axial deviatoric stress is applied step-by-step according to 10%, 20%, 30%, 40%, 50%, and so forth of the UCS (σ3 = 0 MPa) and TCS (triaxial compressive strength) of the composite specimens, the failure stress that the specimen can bear is closely related to the confining pressure. When the confining pressures are 0 MPa, 7 MPa, 15 MPa, and 22 MPa, respectively, the failure stresses that the composite specimens can bear are 60% (corresponds to 0 MPa), 50%, 30%, and 20% of the TCS under the current confining pressures, respectively. Under the same confining pressure, the initial creep rate of the composite specimen on each step shows a U-shaped change trend. Meanwhile, the instantaneous creep rate and failure creep rate of the specimen increase as the confining pressure increases. When the failure creep rate is excluded, the initial creep rate of other stepped loads at the same confining pressure level decreases step-by-step. The improved Nishihara model can better describe the whole creep process of rock-concrete composite specimens, especially in the accelerating creep step. The testing data and research results in this paper can serve as references for further research on mechanical properties of rock-concrete composite structures.

scholarly journals Physical and Mechanical Properties of a Bulk Lightweight Concrete with Expanded Polystyrene (EPS) Beads and Soft Marine Clay

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1662 ◽  
Author(s):  
Jianguo Wang ◽  
Bowen Hu ◽  
Jia Hwei Soon
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Cement Content ◽  
Mass Density ◽  
Physical And Mechanical Properties ◽  
Confining Pressure ◽  
Expanded Polystyrene ◽  
Triaxial Tests ◽  
Filling Material ◽  
Confining Pressures

The variation of physical and mechanical properties of the lightweight bulk filling material with cement and expanded polystyrene (EPS) beads contents under different confining pressures is important to construction and geotechnical applications. In this study, a lightweight bulk filling material was firstly fabricated with Singapore marine clay, ordinary Portland cement and EPS. Then, the influences of EPS beads content, cement content, curing time and confining pressure on the mass density, stress–strain behavior and compressive strength of this lightweight bulk filling material were investigated by unconsolidated and undrained (UU) triaxial tests. In these tests, the mass ratios of EPS beads to dry clay (E/S) were 0%, 0.5%, 1%, 2%, and 4% and the mass ratios of cement to dry clay (C/S) were 10% and 15%. Thirdly, a series of UU triaxial tests were performed at a confining pressure of 0 kPa, 50 kPa, 100 kPa, and 150 kPa after three curing days, seven curing days, and 28 curing days. The results show that the mass density of this lightweight bulk filling material was mainly controlled by the E/S ratio. Its mass density decreased by 55.6% for the C/S ratio 10% and 54.9% for the C/S ratio 15% when the E/S ratio increased from 0% to 4% after three curing days. Shear failure more easily occurred in the specimens with higher cement content and lower confining pressure. The relationships between compressive strength and mass density or failure strain could be quantified by the power function. Increasing cement content and reducing EPS beads content will increase mass density and compressive strength of this lightweight bulk filling material. The compressive strength with curing time can be expressed by a logarithmic function with fitting correlation coefficient ranging from 0.83 to 0.97 for five confining pressures. These empirical formulae will be useful for the estimation of physical and mechanical properties of lightweight concretes in engineering application.

scholarly journals Study on Damage Model and Damage Evolution Characteristics of Backfill with Prefabricated Fracture under Seepage-Stress Coupling

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Jifeng Hou ◽  
Zhongping Guo ◽  
Weizhen Liu ◽  
Hengze Yang ◽  
WenWu Xie
Keyword(s):  
Mechanical Properties ◽  
Damage Evolution ◽  
Coupling Effect ◽  
Water Pressure ◽  
Damage Model ◽  
Confining Pressure ◽  
Seepage Water ◽  
Confining Pressures ◽  
Initial Fracture ◽  
Total Damage

Aiming at the backfill with prefabricated fracture under seepage-stress coupling, the concepts of fracture macrodamage, loaded mesodamage, seepage mesodamage, and total damage of backfill were proposed. Based on the macroscopic statistical damage model, the coupling effect of seepage, stress, and initial fracture was considered comprehensively and the damage model of backfill with prefabricated fracture under seepage-stress coupling was established. The mechanical properties of backfill with prefabricated fracture under different seepage water pressures and confining pressures were tested and the rationality of the model was verified. The research shows that the mechanical properties of backfill with prefabricated fracture under the seepage-stress coupling are determined by the seepage water pressure, the load, the initial fracture, and the coupling effect. Fracture and seepage have significant effects on the damage of the backfill. When the seepage water pressure is low, the fracture damage dominates; however, when the seepage water pressure is high, the seepage damage dominates; the total damage under the coupling action is more serious than the single factor. The development laws of the total damage evolution curves under different seepage water pressures and confining pressures are basically the same, and they show the S-shaped distribution law with the increase of the axial strain. With the increase of confining pressure, the damage effect of fracture and seepage on the backfill is weakened, indicating that the confining pressure has a certain inhibitory effect on the damage evolution of the backfill. The research results can provide a theoretical basis for the study of the stability of backfill with geological defects such as joints and fractures in deep high-stress and high-seepage water pressure coal mines.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

IMPACT OF WATER AND CO2 ON THE MECHANICAL PROPERTIES OF LOW PERMEABLE ROCKS

2021 ◽  
Vol 7 (2) ◽  
pp. 130-146
Author(s):  
Anatolii A. KISLITSYN ◽  
Nikita V. Lipatov
Keyword(s):  
Mechanical Properties ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Pore Fluid ◽  
Co2 Injection ◽  
Core Samples ◽  
Different Temperatures ◽  
Confining Pressures ◽  
Temporary Decrease

This article features experiments on triaxial compression of low-permeable dolomite samples with different confining pressures (2-20 MPa), different pore fluids (dry air, water, CO2), and different temperatures (25-150 °C). The authors have studied the effect of confining pressure, pore fluid and temperature on the strength properties of the studied samples. The results show an increase in the strength with grwoing confining pressure. When the confining pressure increases from 2 to 20 MPa, the compressive strength increases from 86 to 370 MPa. Temperature has a significant effect on rock strength under low confining pressure conditions. With the increasing confining pressure reaching 15 MPa, increasing temperature has little effect on the strength of dolomite samples. Under an effective confining pressure of 5 MPa, the temperature weakening occurs on the dolomite specimens when the temperature exceeds 90 °C. During compression, liquid diffusion occurs in the specimens. Higher water viscosity can cause a temporary decrease in effective confining pressure, which can increase the strength of the rock. More prominent fractures are observed in the samples, and more fluid is injected under CO2 injection conditions, which may be useful for increasing the permeability of the geothermal reservoir. Two groups of experiments have been performed on the samples in this study: the first group of experiments investigated the effect of confining pressure on the fracture stress of core samples, without pore fluid injection; the second group of experiments investigated the effect of water or CO2 and temperature on the mechanical properties of core samples.

scholarly journals An Improved Nishihara Model for Frozen Loess considering the Influence of Temperature

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Xin Li ◽  
Enlong Liu ◽  
Bingtang Song ◽  
Xingyan Liu
Keyword(s):  
Creep Behavior ◽  
Microscopic Analysis ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Frozen Soil ◽  
Experimental Results ◽  
Creep Process ◽  
Model Parameters ◽  
Creep Tests ◽  
Deviator Stress

A series of triaxial creep tests under the constant confining pressure are performed on frozen loess specimens, and the creep behavior of the frozen loess with respect to variations in both temperature and deviator stress is examined. Experimental results illustrate that the frozen loess specimens present the attenuation creep at the lower deviatoric stress, whereas the nonattenuation creep under the higher deviatoric stress level, and with a drop in the temperature, the deviator stress value which the exhibition of nonattenuation creep needs will increase under the constant confining pressure condition. According to the microscopic analysis on deformation characteristics in the creep process of frozen soil, both temperature and external stress will cause the hardening and weakening effects, affecting the creep properties of frozen loess. By introducing the hardening variable and damage variable to consider the hardening and weakening effects of the frozen loess, an improved Nishihara model is proposed. The correlations between model parameters and the temperature as well as deviator stress are determined. The comparisons between model predictions and experimental results show that the improved creep constitutive model proposed here can not only describe the whole creep process well, but also reveal the influences of the temperature and deviator stress on the creep behavior of frozen loess, which demonstrate its accuracy and usefulness.

scholarly journals The Mechanical and Microstructural Properties of Composite Structures Made of a Cement-Tailing Backfill and Rock Core

Minerals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 159
Author(s):  
Yu-ye Tan ◽  
Kai Zhang ◽  
Xin Yu ◽  
Wei-dong Song ◽  
Jie Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Composite Structures ◽  
Failure Process ◽  
Strain Curve ◽  
Special Structure ◽  
Basic Knowledge ◽  
Rock Pillar ◽  
Triaxial Compressive Strength ◽  
The Difference

In underground metal mines that use sublevel or stage open-stope and backfilling mining methods (SSOBMMs), there is a special structure around which both sides of the rock pillar are wrapped by backfill. As a permanent part of an underground mine, how much can backfill improve the rock pillar’s compressive strength? What is the difference in the mechanical properties between the special structure and the signal rock? To explore these questions, a composite structure made of a cement-tailing backfill (CTB) and rock core (RC) was designed. Uniaxial and triaxial compressive strength tests and scanning electron microscope (SEM) were used to research the mechanical properties, failure process, failure characteristics, and microstructure characteristics of the cement-tailing backfill and rock core (CTB-RC) specimens. It was found that the full stress–strain curve of the CTB-RC specimen under triaxial compressive strength (TCS) test had two times the stress increases reaching a lower peak deviator stress two times after the RC was destroyed. The CTB can reduce the destruction and slow down the deformation speed of the inner rock cor (IRC). It can also prevent rigid slip of the IRC after it is damaged and maintain the stability and integrity of the overall structure. The findings of this study can provide some basic knowledge on the mechanical properties of the CTB-RB and provide theoretical guidance for the optimization direction of the width of the rock pillar and the room in mines using SSOBMMs.

scholarly journals Creep Investigation on Shale-Like Material with Preexisting Fissure under Coupling Temperatures and Confining Pressures

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Yongyan Wang ◽  
Hongwei Wang ◽  
Xiao Shi
Keyword(s):  
Steady State ◽  
Creep Rate ◽  
Strain Rate ◽  
Confining Pressure ◽  
Steady State Creep ◽  
Steady State Creep Rate ◽  
Creep Experiment ◽  
Uniaxial Creep ◽  
Confining Pressures ◽  
Triaxial Creep

In order to investigate the influence of temperature, confining pressure, and preexisting fissure on creep characteristics of rock mass, multistage creep experiments were performed on shale-like material, with preexisting fissure under different temperatures and confining pressures. The results showed that new microcracks generated and propagated with the increase of temperature in both uniaxial and triaxial creep experiments, and the generation and propagation were most pronounced at 60°C and least at 20∼50°C in uniaxial creep experiments. The generation and propagation were restricted by confining pressure. Temperature had less influence on the creep strain rate in triaxial creep experiment, whereas it had a significant influence on the steady-state creep rate in uniaxial creep experiment. The influence of confining pressure on the steady-state creep rate was slight when confining pressure was 1 MPa, whereas it was obvious when confining pressure was 3∼7 MPa. The closure of preexisting fissure promoted the creep strain rate, and the closure was incomplete when confining pressure was below 3 MPa, whereas it was complete when confining pressure at 5 and 7 MPa.

Prefabricated Structures Surface Marble Rheological Tests and Constitutive Model Analysis

2014 ◽  
Vol 501-504 ◽  
pp. 419-425
Author(s):  
Qing Xu ◽  
Jiang Da He ◽  
Hong Qiang Xie ◽  
Ming Li Xiao ◽  
Jian Feng Liu
Keyword(s):  
Mechanical Properties ◽  
Rheological Properties ◽  
Flow Rate ◽  
Axial Stress ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Rheological Parameters ◽  
Structural Plane ◽  
High Confining Pressure ◽  
Confining Pressures

The mechanical properties of intact rock and rock containing structural plane are very different. From the diversion tunnel of Jinping deep rock site to retrieve the complete block of marble, after a high confining pressure triaxial compression simulation tectonic movements, the formation of structural plane, it represents the mechanical properties of the original rock. On the surface of the marble structure containing triaxial compression creep tests, the results showed: at low confining pressure, the weak marble surface as micro-damage accumulation, the emergence of non-uniform partial destruction, while at high confining pressure, creep curve better continuity and integrity; different confining pressures, marble initial rheology and stability both appear rheological phase, accelerated phase rheological obvious; different confining pressures, the same stage of the axial stress steady flow rate compared with the confining pressure increases, the axial steady state flow rate becomes smaller; marble under test showed the rheological properties, the use of Nishihara model can better demonstrate the rheological properties and determine the rheological parameters for other practical engineering reference.

scholarly journals Experimental Study on Triaxial Unloading Failure of Deep Composite Coal-Rock

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Xin Li ◽  
Hao Li ◽  
Zhen Yang ◽  
Zhongxue Sun ◽  
Jiayu Zhuang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Failure Criterion ◽  
Confining Pressure ◽  
Exponential Relationship ◽  
Partial Fracture ◽  
Triaxial Compressive Strength ◽  
Confining Pressures ◽  
Unloading Rate ◽  
Coal Rock ◽  
And Control

With the deep mining of coal, the phenomenon of high ground stress is more likely to cause dynamic disaster. In view of the above problems, this paper takes the unloading process of coal mining as the background to study the effects of mining rates under different conditions on the mechanical properties and triaxial failure criterion of composite coal-rock, so as to provide a theoretical basis for the prevention and control of dynamic disasters in coal mines. The composite coal-rock models with a composite ratio of 1 : 1 : 1 were tested under different unloading rates or confining pressures. The results show that the triaxial unloading process of coal-rock can be divided into five stages: compaction, single elasticity, elastic-plastic unloading, partial fracture, and complete fracture. In this paper, the failure criterion of composite coal-rock triaxial unloading is derived. The unloading rate has an exponential relationship with the triaxial compressive strength, and the relationship between initial confining pressure and compressive strength is linear. The triaxial compressive strength is determined by both. The peak strains ε of all samples under different unloading conditions were around 0.01. And initial confining pressure had an influence on the strain variation trend during the unloading of composite coal-rock. The higher the initial confining pressure, the greater the elastic modulus. In addition, an increase of initial confining pressure led to the increase of the total energy converted into dissipated part in the process of fracture and caused the obvious increase of the rebound characteristics of the curve. However, the unloading rate had no influence on the strain trend.

Experimental Study on the Anisotropy of Layered Rock Mass under Triaxial Conditions

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Long Cheng ◽  
Hui Wang ◽  
Xu Chang ◽  
Yewei Chen ◽  
Feilu Xu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Confining Pressure ◽  
Peak Strength ◽  
Rock Composition ◽  
Rock Formations ◽  
Geological Conditions ◽  
Anisotropic Mechanical Properties ◽  
Confining Pressures ◽  
Dip Angle ◽  
Rock Specimens

Weak and hard inhomogeneous rock formations are typically encountered during tunnel excavations. The physical and mechanical properties and geological conditions of these rock formations vary significantly; thus, it is crucial to investigate the mechanical characteristics of deep bedded composite rock formations. Three-dimensional (3D) scanning and 3D printing were used to prepare composite rock specimens to simulate natural rock laminae. Triaxial compression tests were conducted to determine the influence of the bedding angle, rock composition, and confining pressure on the mechanical properties of the composite rock specimens. The anisotropic strength characteristics and the damage patterns of the composite rock specimens were analyzed under different confining pressures, and the failure mechanism during triaxial loading was revealed. The results show that the damage of the composite rock specimens with a bedding structure depends on the bedding dip angle and the rock formation. The stress-strain curves and peak strengths of the composite rock specimens have anisotropic characteristics corresponding to their failure modes. As the bedding dip angle increases, the peak strength of the three groups of specimens first decreases and then increases under different confining pressure levels. The compressive strength has a nonlinear relationship with the confining pressure, and the difference between the compressive strengths of specimens with different inclination angles decreases as the confining pressure increases. The Hoek–Brown strength criterion is a good predictor of the nonlinear increase in peak strength of the composite rock specimens under different confining pressures. The specimen with a β  = 60°dip angle shows the most significant increase in the strength difference with increasing confining pressure. The results can be used as a reference for testing and analyzing the anisotropic mechanical properties of bedded rock masses.

Sign in / Sign up

Export Citation Format

Share Document