scholarly journals Morphological and Mechanical Properties of Poly (Butylene Terephthalate)/High-Density Polyethylene Blends

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Nga Thi-Hong Pham ◽  
Van-Thuc Nguyen
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
High Density Polyethylene ◽  
Polyester Resin ◽  
High Density ◽  
Heterogeneous Mixture ◽  
Two Phase ◽  
Butylene Terephthalate ◽  
Polyethylene Blends ◽  
Sem Microstructure

Poly (butylene terephthalate) (PBT) is a popular thermoplastic polyester resin but has low strength and low melting point. To improve its properties, PBT is often mixed with other resins, such as high-density polyethylene (HDPE). In this study, PBT/HDPE samples with 100% PBT, 5%, 10%, 15%, and 100% HDPE are generated and tested. The samples are analyzed by tensile strength, flexural strength, impact strength, and SEM tests. Adding HDPE will reduce tensile strength compared to pure PBT, in which 5%, 10%, and 15% PBT/HDPE samples obtain the values 40.23, 38.11, and 27.77 MPa, respectively. These values are lower than that of pure PBT but still higher than that of HDPE. Improving the HDPE portion mostly results in decreasing flexural strength. The flexural strengths of these samples are 87.79, 70.47, 55.3, 58.98, and 19.14 MPa corresponding to 100% PBT, 5%, 10%, 15%, and 100% HDPE samples, respectively. Moreover, the SEM microstructure of PBT and HDPE indicates a two-phase heterogeneous mixture with little or no adhesion between these phases.

Effects of PMDI Modified on Physico-Mechanical Properties of Silvergrass Reinforced High Density Polyethylene Composites

2013 ◽  
Vol 750-752 ◽  
pp. 38-42
Author(s):  
Wang Wang Yu ◽  
Juan Li ◽  
Yun Ping Cao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
High Density Polyethylene ◽  
High Density ◽  
Hydroxyl Groups ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
Methylene Diphenyl Diisocyanate

In this study, the silvergrass (SV) was used to reinforce HDPE composites. The effects of polymeric methylene diphenyl diisocyanate (PMDI) content, slivergrass fibers content on the mechanical, water absortion of wood plastic composites (WPCs) were investigated. It was found that the mechanical properties of the SV reinforced HDPE composites can be improved by PMDI treatment. The highest tensile strength and flexural strength of the composites can be reached with 50% SV contents at the SV: PMDI=6:1. It has been proved that the hydroxyl groups of SV fibers which can react with the-NCO by FTIR. It also can be concluded that the water absorption of PMDI treated WPCs was lower than untreated ones.

Effects of MAPE Modified on Physico-Mechanical Properties of Silvergrass Reinforced High Density Polyethylene Composites

2013 ◽  
Vol 423-426 ◽  
pp. 53-57
Author(s):  
Wang Wang Yu ◽  
Cai Hong Li ◽  
Juan Li ◽  
Jian Peng Zhang ◽  
Chang Wei Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Injection Molding ◽  
Differential Scanning Calorimeter ◽  
High Density Polyethylene ◽  
Nucleating Agent ◽  
High Density ◽  
Tensile Fracture ◽  
Sem Images

In this study, silvergrass (SV) reinforced high density polyethylene (HDPE) composites (WPCs) were prepared by injection molding. The effects of maleated polyethylene (MAPE), slivergrass fibers content on the mechanical, Differential scanning calorimeter, morphologies of WPCs were investigated. It was found that the mechanical properties of the SV reinforced HDPE composites can be improved by MAPE treatment. The highest tensile strength and flexural strength of the composites can be reached with 40% and 50% SV contents at the fixed 8% MAPE respectively. The SV can be the nucleating agent with the addition of MAPE. SEM images of tensile fracture surfaces of treated composites demonstrated better fiber-matrix adhesion.

Resistance Welding Process Development and Optimization for Recycled High-Density Polyethylene (HDPE)

2015 ◽  
Author(s):  
Peter F. Baumann ◽  
Lucas Sendrowski
Keyword(s):  
Tensile Strength ◽  
Response Surface ◽  
High Density Polyethylene ◽  
Heating Temperature ◽  
Base Material ◽  
Heating Time ◽  
High Density ◽  
Hot Plate ◽  
Initial Testing ◽  
Hot Plate Welding

Large recycled high-density polyethylene (HDPE) structural members, difficult to manufacture by extrusion processes, have been created by the hot plate welding of simple plastic lumber sections. Hot plate welding generates better joint strength than any other welding method currently employed in plastic manufacturing. However, to achieve the desired temperature of the thick plate to melt the polymer uniformly, the process needs a high amount of heat energy requiring furnace (or resistance) heating of a considerable mass. A new method which could combine the heating element and a thin plate into one source could be more efficient in terms of heat loss and thus energy used. The premise of this investigation is to replace the hot plate with a very thin piece of high resistance nickel-chromium alloy ribbon to localize the application of heat within a plastic weld joint in order to reduce energy loss and its associated costs. This resistance ribbon method uses electrical current to reach an adequate temperature to allow for the welding of the HDPE plastic. The ribbon is only slightly larger than the welding surface and very thin to reduce the loss of excess heat through unused surface area and thick sides. The purpose of this project was to weld recycled high-density polyethylene (HDPE) using resistance welding and to match the tensile strength results considered acceptable in industry for hot plate welding, that is, equal to or greater than 80% of the base material strength. Information obtained through literature review and previous investigations in our laboratories established welding (heating) temperature and time as testing factors. Designed experimentation considered these factors in optimizing the process to maximize the weld tensile strength. A wide-ranging full-factorial experimental design using many levels was created for the initial testing plan. Tensile strengths obtained after welding under the various condition combinations of weld temperature and time revealed a region of higher strength values in the response surface. After the wide-range initial testing, the two control parameters, heating temperature and heating time, were ultimately set up in a focused Face Centered Cubic (FCC) Response Surface Method (RSM) testing design and the tensile strength response was then analyzed using statistical software. The results obtained indicated a strong correlation between heating time and heating temperature with strength. All welded samples in the final testing set exhibited tensile strength of over 90% base material, meeting the goal requirements. A full quadratic equation relationship for tensile strength as a function of welding time and temperature was developed and the maximum tensile strength was achieved when using 280°C for 60 seconds.

Gamma radiation curing of nitrile rubber/high density polyethylene blends

2012 ◽  
Vol 293 (3) ◽  
pp. 941-947 ◽  
Author(s):  
E. Elshereafy ◽  
Maysa A. Mohamed ◽  
M. M. EL-Zayat ◽  
A. A. El Miligy
Keyword(s):  
Gamma Radiation ◽  
High Density Polyethylene ◽  
Nitrile Rubber ◽  
High Density ◽  
Radiation Curing ◽  
Polyethylene Blends

scholarly journals In-Situ Synthesis and Property Evaluation of High-Density Polyethylene Reinforced Groundnut Shell Particulate Composite

2021 ◽  
Vol 6 (4) ◽  
pp. 305-311
Author(s):  
Abdulmumin Adebisi ◽  
Tajudeen Mojisola ◽  
Umar Shehu ◽  
Muhammed Sani Adam ◽  
Yusuf Abdulaziz
Keyword(s):  
Tensile Strength ◽  
Water Absorption ◽  
Impact Energy ◽  
High Density Polyethylene ◽  
In Situ Synthesis ◽  
High Density ◽  
Compression Moulding ◽  
Melt Mixing ◽  
Groundnut Shell

In-situ synthesis of high-density polyethylene (HDPE) reinforced groundnut shell particulate (GSP) composite with treated GSP within the range of 10-30 wt% at 10 wt% has been achieved. The adopted technique used in the production of the composite is melt mixing and compounding using two roll mills with a compression moulding machine. Properties such as hardness, tensile strength, impact energy and water absorption analysis were examined. The result revealed that addition of GSP increases the hardness value from 22.3 to 87 Hv. However, the tensile strength progressively decreased as the GSP increases in the HDPE. This trend arises due to the interaction between neighbouring reinforced particulate which appears to influence the matrix flow, thereby inducing embrittlement of the polymer matrix. It was also observed that water absorption rate steadily increased with an increase in the exposure time and the absorbed amount of water increases by increasing the wt% of the GSP. Analysing the obtained results, it was concluded that there were improvements in the hardness, tensile strength, impact energy and water absorption properties of the HDPE-GSP polymer composite when compared to unreinforced HDPE. On these premises, GSP was found as a promising reinforcement which can positively influence the HDPE properties of modern composites.

Tensile and flammability characterizations of corn straw slagging/high-density polyethylene composites

2019 ◽  
Vol 33 (11) ◽  
pp. 1466-1477
Author(s):  
Qingfa Zhang ◽  
Wenyu Lu ◽  
Liang Zhou ◽  
Donghong Zhang ◽  
Hongzhen Cai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Flame Retardant ◽  
High Density Polyethylene ◽  
Oxygen Index ◽  
High Density ◽  
Corn Straw ◽  
Scanning Calorimetry ◽  
Scanning Electron

Biocomposites were prepared with corn straw slagging (CSS) and high-density polyethylene (HDPE) at four loading levels (10, 20, 30, and 40 wt%) by extrusion method. CSS/HDPE composites were tested by tension, oxygen index meter, differential scanning calorimetry, X-ray diffraction, and the scanning electron microscopy. The scanning electron microscopy showed that CSS was dispersed uniformly in the HDPE matrix and strong interfacial interaction was achieved, which had an important influence on the tensile strength of the composites. The tensile strength of the composites could be improved with proper increase of CSS and reached maximum value at 30 wt% content. Furthermore, the addition of CSS played an important role in improving the flame-retardant ability of CSS/HDPE composites, and the limited oxygen index was 31.26% at 40 wt% content, good flame-retardant effect achieved.

scholarly journals Enhancement of the processing window and performance of polyamide 1010/bio‐based high‐density polyethylene blends by melt mixing with natural additives

2019 ◽  
Vol 69 (1) ◽  
pp. 61-71 ◽  
Author(s):  
Luis Quiles‐Carrillo ◽  
Nestor Montanes ◽  
Vicent Fombuena ◽  
Rafael Balart ◽  
Sergio Torres‐Giner
Keyword(s):  
High Density Polyethylene ◽  
High Density ◽  
Melt Mixing ◽  
Polyethylene Blends ◽  
Processing Window ◽  
And Performance ◽  
Polyamide 1010 ◽  
Natural Additives

Effect of Date Palm Fiber Loadings on the Mechanical Properties of High Density Polyethylene/Date Palm Fiber Composites

2018 ◽  
Vol 773 ◽  
pp. 94-99 ◽  
Author(s):  
Venitalitya Augustia ◽  
Achmad Chafidz ◽  
Lucky Setyaningsih ◽  
Muhammad Rizal ◽  
Mujtahid Kaavessina ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Water Absorption ◽  
High Density Polyethylene ◽  
Date Palm ◽  
Agricultural Waste ◽  
Natural Fibers ◽  
High Density ◽  
Palm Fiber ◽  
Test Result

The trend of using natural fibers as green filler in the fabrication of polymer composites is increasing. One of these natural fibers is date palm fiber (DPF). Date palm fiber is considered as agricultural waste in certain areas, such as Middle East countries. Therefore, the utilization of this fiber in the composites fabrication is an interesting topic of research. In the current study, composites were prepared by melt blending DPF with high density polyethylene (HDPE). Five different DPF loadings were studied (i.e. 0, 5, 10, 20, 30 wt%). The effect of the DPF loadings on the mechanical properties and water absorption behavior of the composites were investigated. The tensile test result showed that tensile strengths of all the composites samples were all higher than the neat HDPE with the maximum improvement was achieved at the DPF loading of 5 wt% (i.e. DFC-5), which was about 19.23 MPa (138% higher than the neat HDPE). Whereas, the flexural test result showed that the flexural strength of the composites slightly increased compared to that of the neat HDPE only until 5 wt% DPF loading (i.e. DFC-5). Afterward, the flexural strength of the DFC-10 was equal to that of the neat HDPE, and decreasing with further increase of DPF loadings. Additionally, the water absorption test result showed that the water absorption rate and uptake of water (at equilibrium) increased with the increase of DPF loading.

Investigations into the mechanical, morphological and thermal analyses of friction stir processing of high-density polyethylene composites

2016 ◽  
Vol 232 (7) ◽  
pp. 1193-1200 ◽  
Author(s):  
Jicheng Gao ◽  
Chao Li ◽  
Yifu Shen
Keyword(s):  
Tensile Strength ◽  
Friction Stir Processing ◽  
High Density Polyethylene ◽  
Thermal Analyses ◽  
Experimental Tests ◽  
Traverse Speed ◽  
High Density ◽  
Scanning Calorimetry ◽  
Friction Stir ◽  
Polyethylene Composites

The aim of this work is to fabricate the high-density polyethylene–copper composites by submerged friction stir processing at different traverse speeds. The scanning electron microscopy is used to analyze the distribution of microstructure and particles. The experimental results indicated that the macrostructure morphology, microstructure and tensile strength vary depending on the traverse speed. Compared with the pure high-density polyethylene, Cu-filled polymer composites showed lower tensile strength and higher microhardness. The maximal values of the tensile strength and microhardness were achieved at traverse speeds of 30 and 15 mm/min, respectively. The thermal properties of Cu-filled high-density polyethylene composites were studied by differential scanning calorimetry. The crystalline content of the composites was decreased due to the addition of copper. From the experimental tests, it can be concluded that submerged fiction stir processing has a great potential for producing polymer–metal composites.

Sign in / Sign up

Export Citation Format

Share Document