scholarly journals Elliptical FRP-Concrete-Steel Double-Skin Tubular Columns under Monotonic Axial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-16 ◽  
Author(s):  
Bing Zhang ◽  
Gui-Sen Feng ◽  
Yan-Lei Wang ◽  
Cong-Cong Lai ◽  
Chen-Chen Wang ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Steel Tube ◽  
Confined Concrete ◽  
Stress Strain ◽  
Tubular Columns ◽  
Strength Enhancement ◽  
Double Skin ◽  
The Cross ◽  
Frp Tube

Hybrid FRP-concrete-steel double-skin tubular columns (hybrid DSTCs) are a novel form of hollow columns consisting of an outer FRP tube, an inner steel tube, and an annular layer of concrete between the two tubes. Due to the effective confinement of the two tubes, the concrete in hybrid DSTCs is well confined, leading to excellent ductility and strength enhancement. Hybrid DSTCs also have excellent corrosion resistence due to the effective protection of the outer FRP tube. However, existing studies mainly focused on hybrid DSTCs with a circular cross-section. When subjecting to different loads in the two horizontal directions, elliptical columns are preferred as they can provide different bending stiffness and moment capacity around two axes of symmetry without significantly reducing the confining effect of the FRP tube. This paper extends the existing work on circular DSTCs to elliptical DSTCs with a particular focus on four issues: the effect of elliptical aspect ratio (i.e., the ratio of the major axis to the minor axis of the outer elliptical cross-section), the effect of the FRP tube thickness, the effect of void area ratio (i.e., the ratio of the area of concrete void to the area of the outer elliptical section), and the effect of the cross-section of the inner steel tube (i.e., both rectangular and elliptical steel tubes were used). Experimental results show that, the averaged peak stress of the confined concrete in elliptical DSTCs increases with the increase in the elliptical aspect ratio, whereas the elliptical aspect ratio has no obvious effect on the ultimate axial strain; the cross-section shape of the inner steel tube has significant effect on the axial stress-strain behavior of the confined concrete in elliptical DSTCs; elliptical DSTCs with an elliptical steel tube exhibit much better ductility and strength enhancement than those specimens with a rectangular steel tube. A simple stress-strain model of confined concrete was proposed for elliptical DSTCs to account for the effects of the elliptical aspect ratio, the inner void, and the shape of the inner steel tube, which can provide reasonably accurate but conservative predictions.

scholarly journals Effect of Cross-Sectional Aspect Ratio on Rectangular FRP-Concrete-Steel Double-Skin Tubular Columns under Axial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Bing Zhang ◽  
Xia-Min Hu ◽  
Wei Wei ◽  
Qian-Biao Zhang ◽  
Ning-Yuan Zhang ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Axial Stress ◽  
Axial Strain ◽  
Steel Tube ◽  
Confined Concrete ◽  
Cross Sectional ◽  
Tubular Columns ◽  
Double Skin ◽  
Frp Tube

Hybrid FRP-concrete-steel double-skin tubular columns (hybrid DSTCs) are novel hollow columns consisting of an outer FRP tube, an inner steel tube, and the concrete between the two tubes. Hybrid DSTCs possess important advantages, such as excellent corrosion resistance as well as remarkable seismic resistance. However, existing studies are mainly focused on hybrid DSTCs with a circular cross section or a square cross section. When a column is subjected to different load levels in the two horizontal directions, a rectangular column is preferred as it can provide different bending stiffness and moment capacity around its two axes of symmetry. This paper presents an experimental study on rectangular DSTCs with a particular focus on the effect of the cross-sectional aspect ratio (i.e., the ratio of the breadth to the width of the rectangular cross section). The effect of the cross-sectional shape of the inner steel tube (i.e., both elliptical and rectangular inner steel tubes were used) and the effect of FRP tube thickness were also investigated experimentally. Experimental results show that a larger aspect ratio will have no negative effect on the confinement effect in rectangular DSTCs; a rectangular DSTC with a larger aspect ratio generally has a larger ultimate axial strain and a higher axial stress at the ultimate axial strain; rectangular DSTCs with an elliptical steel tube generally have better performance than corresponding specimens with a rectangular steel tube. An existing model, which was developed based on a model for rectangular FRP-confined concrete columns and a model for circular DSTCs, is verified using the test results of the present study. The model generally provides close predictions for the peak axial stress of the confined concrete but yields conservative predictions for the ultimate axial strain for rectangular DSTCs.

Compressive Behavior of Large-Scale Hybrid FRP-Concrete-Steel Double-Skin Tubular Columns

2011 ◽  
Vol 243-249 ◽  
pp. 1138-1144 ◽  
Author(s):  
Pan Xie ◽  
T Yu ◽  
Y.L. Wong ◽  
J.G. Teng
Keyword(s):  
Large Scale ◽  
Experimental Studies ◽  
Steel Tube ◽  
Small Scale ◽  
Structural Members ◽  
Compression Tests ◽  
Tubular Columns ◽  
Compressive Response ◽  
Double Skin ◽  
Frp Tube

Hybrid FRP-concrete-steel double-skin tubular columns (DSTCs) are a new form of hybrid structural members. A hybrid DTSC consists of an inner steel tube, an outer FRP tube and a concrete infill between them. Hybrid DSTCs possess many important advantages over conventional structural members, including their excellent corrosion resistance as well as excellent ductility and seismic resistance. A large amount of research has been conducted on hybrid DSTCs, but the existing experimental studies have been limited to the testing of small-scale columns. This paper presents preliminary results from the first series of large-scale axial compression tests on hybrid DSTCs, which forms part of a larger experimental study currently under way at The Hong Kong Polytechnic University. These test results confirm the excellent axial compressive response of hybrid DSTCs as initially expected.

scholarly journals Axial Compression Behaviour of Hybrid Double-Skin Tubular Columns Filled with Rubcrete

2019 ◽  
Vol 3 (2) ◽  
pp. 62 ◽  
Author(s):  
Osama Youssf ◽  
Reza Hassanli ◽  
Julie E. Mills ◽  
Yan Zhuge
Keyword(s):  
Wall Thickness ◽  
Steel Tube ◽  
Hoop Strain ◽  
Conventional Concrete ◽  
Tubular Columns ◽  
Rubber Particles ◽  
Fibre Reinforced Polymer ◽  
Double Skin ◽  
Adverse Influence ◽  
Frp Tube

Double-skin tubular columns (DSTCs) have become a competitive candidate for column members due to their important advantages compared with conventional reinforced concrete columns, including their better weight-to-strength ratio and ease of construction. Using Rubcrete in hybrid DSTCs is of great interest due to the potential of this system to overcome the Rubcrete material deficiencies and to add more ductility, toughness, seismic resistance, confinement effectiveness, and environmentally-friendly features to that structural system compared to conventional concrete. In this paper, hybrid DSTCs made out of Rubcrete, sandwiched between a fibre reinforced polymer (FRP) tube and a steel tube, were tested. The examined variables were concrete sand or stone replacement ratio (0% and 20%), FRP wall thickness (1- and 2-layers), steel wall thickness (3.2 mm and 4.5 mm), void ratio (50% and 76%), and void shape (circular or square). The axial and lateral stress–strain responses were monitored, measured, and compared. According to this investigation, using Rubcrete in hybrid DSTCs can enhance the axial and hoop strain capacities, especially with fine rubber particles. It was also observed that the adverse influence of using rubber on column ultimate capacity was much lower in DSTC specimens, compared with that of unconfined Rubcrete columns. Therefore, using Rubcrete with fine rubber particles is recommended in DSTC structural columns.

Effect of Geometry on Droplet Generation in a Microfluidic T-Junction

2013 ◽  
Author(s):  
Katerina Loizou ◽  
Wim Thielemans ◽  
Buddhika N. Hewakandamby
Keyword(s):  
Aspect Ratio ◽  
Cross Section ◽  
Droplet Formation ◽  
Continuous Phase ◽  
Main Channel ◽  
Superficial Velocity ◽  
Droplet Generation ◽  
Dispersed Phase ◽  
Aspect Ratios ◽  
The Cross

The main aim of this study is to examine how the droplet formation in microfluidic T-junctions is influenced by the cross-section and aspect ratio of the microchannels. Several studies focusing on droplet formation in microfluidic devices have investigated the effect of geometry on droplet generation in terms of the ratio between the width of the main channel and the width of the side arm of the T-junction. However, the contribution of the aspect ratio and thus that of the cross-section on the mechanism of break up has not been examined thoroughly with most of the existing work performed in the squeezing regime. Two different microchannel geometries of varying aspect ratios are employed in an attempt to quantify the effect of the ratio between the width of the main channel and the height of the channel on droplet formation. As both height and width of microchannels affect the area on which shear stress acts deforming the dispersed phase fluid thread up to the limit of detaching a droplet, it is postulated that geometry and specifically cross-section of the main channel contribute on the droplet break-up mechanisms and should not be neglected. The above hypothesis is examined in detail, comparing the volume of generated microdroplets at constant flowrate ratios and superficial velocities of continuous phase in two microchannel systems of two different aspect ratios operating at dripping regime. High-speed imaging has been utilised to visualise and measure droplets formed at different flowrates corresponding to constant superficial velocities. Comparing volumes of generated droplets in the two geometries of area ratio near 1.5, a significant increase in volume is reported for the larger aspect ratio utilised, at all superficial velocities tested. As both superficial velocity of continuous phase and flowrate ratio are fixed, superficial velocity of dispersed phase varies. However this variation is not considered to be large enough to justify the significant increase in the droplet volume. Therefore it can be concluded that droplet generation is influenced by the aspect ratio and thus the cross-section of the main channel and its effect should not be depreciated. The paper will present supporting evidence in detail and a comparison of the findings with the existing theories which are mainly focused on the squeezing regime.

Springback law of high-strength 21-6-9 stainless steel tube in numerical control bending under different process parameters

2015 ◽  
Vol 231 (10) ◽  
pp. 1783-1792 ◽  
Author(s):  
Jun Fang ◽  
Shiqiang Lu ◽  
Kelu Wang ◽  
Zhengjun Yao
Keyword(s):  
Stainless Steel ◽  
Friction Coefficient ◽  
Cross Section ◽  
Process Parameters ◽  
High Strength ◽  
Steel Tube ◽  
Numerical Control ◽  
Stainless Steel Tube ◽  
Outer Diameter ◽  
The Cross

In order to achieve the precision bending deformation, the effects of process parameters on springback behaviors should be clarified preliminarily. Taking the 21-6-9 high-strength stainless steel tube of 15.88 mm × 0.84 mm (outer diameter × wall thickness) as the objective, the multi-parameter sensitivity analysis and three-dimensional finite element numerical simulation are conducted to address the effects of process parameters on the springback behaviors in 21-6-9 high-strength stainless steel tube numerical control bending. The results show that (1) springback increases with the increasing of the clearance between tube and mandrel Cm, the friction coefficient between tube and mandrel fm, the friction coefficient between tube and bending die fb, or with the decreasing of the mandrel extension length e, while the springback first increases and then remains unchanged with the increasing of the clearance between tube and bending die Cb. (2) The sensitivity of springback radius to process parameters is larger than that of springback angle. And the sensitivity of springback to process parameters from high to low are e, Cb, Cm, fb and fm. (3) The variation rules of the cross section deformation after springback with different Cm, Cb, fm, fb and e are similar to that before springback. But under same process parameters, the relative difference of the most measurement section is more than 20% and some even more than 70% before and after springback, and a platform deforming characteristics of the cross section deformation is shown after springback.

scholarly journals Axial Behavior of Concrete-Filled Double-Skin Tubular Stub Columns Incorporating PVC Pipes

Crystals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1434
Author(s):  
Muhammmad Faisal Javed ◽  
Haris Rafiq ◽  
Mohsin Ali Khan ◽  
Fahid Aslam ◽  
Muhammad Ali Musarat ◽  
...  
Keyword(s):  
Steel Tube ◽  
Tube Material ◽  
Steel Tubes ◽  
Tubular Columns ◽  
Axial Capacity ◽  
Double Skin ◽  
Axial Behavior ◽  
Pvc Pipe ◽  
The Cost ◽  
Stub Columns

This experimental study presents concrete-filled double-skin tubular columns and demonstrates their expected advantages. These columns consist of an outer steel tube, an inner steel tube, and concrete sandwiched between two tubes. The influence of the outer-to-inner tube dimension ratio, outer tube to thickness ratio, and type of inner tube material (steel, PVC pipe) on the ultimate axial capacity of concrete-filled double-skin tubular columns is studied. It is found that the yield strength of the inner tube does not significantly affect the ultimate axial capacity of concrete-filled double-skin tubular composites. With the replacement of the inner tube of steel with a PVC pipe, on average, less than 10% strength is reduced, irrespective of size and dimensions of the steel tube. Hence, the cost of a project can be reduced by replacing inner steel tubes with a PVC pipes. Finally, the experimental results are compared with the existing design methods presented in AISC 360-16 (2016), GB51367 (2019), and EC4 (2004). It is found from the comparison that GB51367 (2019) gives better results, followed by AISC (2016) and EC4 (2004).

Prior and post peaks compressive behavior of concrete-filled double-skin tubular columns with BFRP-punched-in outer steel and BFRP-circular inner steel

2020 ◽  
Vol 23 (13) ◽  
pp. 2911-2927
Author(s):  
Yung William Sasy Chan ◽  
Zhi Zhou ◽  
Zhenzhen Wang ◽  
Jinping Ou
Keyword(s):  
Load Capacity ◽  
High Energy ◽  
Fiber Reinforced Polymer ◽  
Confined Concrete ◽  
Peak Performance ◽  
Design Parameters ◽  
Fiber Reinforced ◽  
Tubular Columns ◽  
Reinforced Polymer ◽  
Double Skin

Fiber-reinforced polymer composites have been widely used to design fiber-reinforced polymer–based confined concrete columns with potential benefits. However, it is critical to design a column with sufficient post-peak performance that can prevent its collapse at the rupture of the fiber-reinforced polymer tube. This article presents the experimental results on the prior and post peaks behavior of concrete-filled double-skin tubular columns with basalt fiber-reinforced polymer (BFRP)–punched-in outer steel and BFRP-circular inner steel (BFST-DSTCs). Twenty-two specimens were tested under axial compression to investigate the effects of design parameters on the behavior of the BFST-DSTC. The outcomes reveal that the BFST-DSTC exhibits the best performance in terms of load capacity, confinement ratio, failure and damage mechanisms, and ductility in prior and post peaks. The inner fiber-reinforced polymer jacket delays the buckling of the inner tube. The punched-in patterns of the outer steel improve the confinement effectiveness of the fiber-reinforced polymer jacket. The BFST-DSTC displays a good post-peak performance with high-energy dissipation capacity that prevents the concerned structure from collapse after the fiber-reinforced polymer jacket rupture. Finally, a new confinement model is proposed to predict the ultimate point of the confined concrete.

Numerical Simulation on Temperature Field of CFST Member under Solar Radiation

2011 ◽  
Vol 354-355 ◽  
pp. 1241-1244
Author(s):  
Yan He ◽  
Man Ding ◽  
Qian Zhang
Keyword(s):  
Numerical Simulation ◽  
Temperature Field ◽  
Temperature Distribution ◽  
Solar Radiation ◽  
Cross Section ◽  
Temperature Difference ◽  
Steel Tube ◽  
Concrete Filled Steel Tube ◽  
Nonlinear Temperature ◽  
The Cross

In this paper the temperature field of Concrete Filled Steel Tube (CFST) member under solar radiation is simulated. The results show that temperature distribution caused by solar radiation is nonlinear over the cross-section of CFST member, and it is significantly varied with time and sections, the largest nonlinear temperature difference is over 26.3°C.

Sign in / Sign up

Export Citation Format

Share Document