scholarly journals Virtual Synchronous Generator Control of VSC-HVDC System Based on MMC of Hybrid Topology

2020 ◽  
Vol 2020 ◽  
pp. 1-8 ◽  
Author(s):  
Jie Wu ◽  
Chuanjiang Li
Keyword(s):  
Control Strategy ◽  
Closed Loop ◽  
Structural Characteristics ◽  
Synchronous Generator ◽  
Current Control ◽  
Current Loop ◽  
Power Module ◽  
Loop Control ◽  
Hybrid Topology ◽  
Virtual Synchronous Generator

For a VSC-HVDC transmission system based on a hybrid topology converter of full-bridge and half-bridge, a kind of virtual synchronous generator (VSG) control strategy which can be applied to modular multilevel converter (MMC) grid-connected structure was researched and proposed. First, based on the conventional VSG control strategy, the energy stored in the equivalent capacitor of MMC power module was used to imitate the rotor inertia of synchronous generator. The characteristics of generator can be simulated during transient frequency fluctuations and it can help relieve the power fluctuations. Secondly, with respect to the structural characteristics of the direct grid connection through the reactor on the AC side of the MMC, which is unlike the microgrid inverter, there are no additional filter capacitors. So, the existing commonly used VSG control strategy of the microgrid inverter and double-closed-loop structure composed of filter capacitor voltage and AC current cannot be directly applied. For this, a method where the given values of inner current loop are calculated by grid impedance matrix was used. So, a double-closed-loop control structure composed of a power outer loop based on VSG control and a current inner loop is obtained. It can effectively improve the current control capability during the transient process. Finally, a hybrid MMC simulation model was built based on PSCAD to verify the correctness and effectiveness of the proposed methods.

scholarly journals Synchronous Generator Rectification System Based on Double Closed-Loop Control of Backstepping and Sliding Mode Variable Structure

Electronics ◽  
2021 ◽  
Vol 10 (15) ◽  
pp. 1832
Author(s):  
Jinfeng Liu ◽  
Xin Qu ◽  
Herbert Ho-Ching Iu
Keyword(s):  
Closed Loop ◽  
Control Structure ◽  
Low Voltage ◽  
Sliding Mode ◽  
Variable Structure ◽  
Synchronous Generator ◽  
Closed Loop Control ◽  
High Current ◽  
Loop Control ◽  
Sliding Mode Variable Structure

Low-voltage and high-current direct current (DC) power supplies are essential for aerospace and shipping. However, its robustness and dynamic response need to be optimized further on some special occasions. In this paper, a novel rectification system platform is built with the low-voltage and high-current permanent magnet synchronous generator (PMSG), in which the DC voltage double closed-loop control system is constructed with the backstepping control method and the sliding mode variable structure (SMVS). In the active component control structure of this system, reasonable virtual control variables are set to obtain the overall structural control variable which satisfied the stability requirements of Lyapunov stability theory. Thus, the fast-tracking and the global adjustment of the system are realized and the robustness is improved. Since the reactive component control structure is simple and no subsystem has to be constructed, the SMVS is used to stabilize the system power factor. By building a simulation model and experimental platform of the 5 V/300 A rectification module based on the PMSG, it is verified that the power factor of the system can reach about 98.5%. When the load mutation occurs, the DC output achieves stability again within 0.02 s, and the system fluctuation rate does not exceed 2%.

A Control Strategy for Intelligent Stamp Forming Tooling

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
William J. Emblom ◽  
Klaus J. Weinmann
Keyword(s):  
Fuzzy Logic ◽  
Control Systems ◽  
Control Strategy ◽  
Pid Controller ◽  
Closed Loop ◽  
Closed Loop Control ◽  
Linear Quadratic ◽  
Blank Holder ◽  
Loop Control ◽  
Stamp Forming

This paper describes the development and implementation of closed-loop control for oval stamp forming tooling using MATLAB®’s SIMULINK® and the dSPACE®CONTROLDESK®. A traditional PID controller was used for the blank holder pressure and an advanced controller utilizing fuzzy logic combining a linear quadratic gauss controller and a bang–bang controller was used to control draw bead position. The draw beads were used to control local forces near the draw beads. The blank holder pressures were used to control both wrinkling and local forces during forming. It was shown that a complex, advanced controller could be modeled using MATLAB’s SIMULINK and implemented in DSPACE CONTROLDESK. The resulting control systems for blank holder pressures and draw beads were used to control simultaneously local punch forces and wrinkling during the forming operation thereby resulting in a complex control strategy that could be used to improve the robustness of the stamp forming processes.

Sign in / Sign up

Export Citation Format

Share Document