scholarly journals Maximum Obtainable Energy Harvesting Power from Galloping-Based Piezoelectrics

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Mohammad Yaghoub Abdollahzadeh Jamalabadi ◽  
Mostafa Safdari Shadloo ◽  
Arash Karimipour
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Average Power ◽  
Electrical Energy ◽  
Load Resistance ◽  
Nonlinear Motion ◽  
Rc Circuit ◽  
Deflection Limit

In this paper, the maximum obtainable energy from a galloping cantilever beam is found. The system consists of a bluff body in front of wind which was mounted on a cantilever beam and supported by piezoelectric sheets. Wind energy caused the transverse vibration of the beam and the mechanical energy of vibration is transferred to electrical charge by use of piezoelectric transducer. The nonlinear motion of the Euler–Bernoulli beam and conservation of electrical energy is modeled by lumped ordinary differential equations. The wind forces on the bluff body are modeled by quasisteady aeroelasticity approximation where the fluid and solid corresponding dynamics are disconnected in time scales. The linearized motion of beam is limited by its yield stress which causes to find a limit on energy harvesting of the system. The theory founded is used to check the validity of previous results of researchers for the effect of wind speed, tip cross-section geometry, and electrical load resistance on onset speed to galloping, tip displacement, and harvested power. Finally, maximum obtainable average power in a standard RC circuit as a function of deflection limit and synchronized charge extraction is obtained.

A Creative Vibration Energy Harvesting System to Support a Self-Powered Internet of Thing (IoT) Network in Smart Bridge Monitoring

2020 ◽  
Author(s):  
Saman Farhangdoust ◽  
Claudia Mederos ◽  
Behrouz Farkiani ◽  
Armin Mehrabi ◽  
Hossein Taheri ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Average Power ◽  
Electrical Energy ◽  
Laser Vibrometer ◽  
Stay Cable ◽  
Fe Modelling ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

Abstract This paper presents a creative energy harvesting system using a bimorph piezoelectric cantilever-beam to power wireless sensors in an IoT network for the Sunshine Skyway Bridge. The bimorph piezoelectric energy harvester (BPEH) comprises a cantilever beam as a substrate sandwiched between two piezoelectric layers to remarkably harness ambient vibrations of an inclined stay cable and convert them into electrical energy when the cable is subjected to a harmonic acceleration. To investigate and design the bridge energy harvesting system, a field measurement was required for collecting cable vibration data. The results of a non-contact laser vibrometer is used to remotely measure the dynamic characteristics of the inclined cables. A finite element study is employed to simulate a 3-D model of the proposed BPEH by COMSOL Multiphasics. The FE modelling results showed that the average power generated by the BPEH excited by a harmonic acceleration of 1 m/s2 at 1 Hz is up to 614 μW which satisfies the minimum electric power required for the sensor node in the proposed IoT network. In this research a LoRaWAN architecture is also developed to utilize the BPEH as a sustainable and sufficient power resource for an IoT platform which uses wireless sensor networks installed on the bridge stay cables to collect and remotely transfer bridge health monitoring data over the bridge in a low-power manner.

Effects of Downstream Structures on Aero Elastic Energy Harvesters From Wake-Induced Vibration

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Pakorn Uttayopas ◽  
Chawalit Kittichaikarn
Keyword(s):  
Cantilever Beam ◽  
Polyvinylidene Fluoride ◽  
Bluff Body ◽  
Electrical Energy ◽  
Load Resistance ◽  
High Amplitude ◽  
Triangular Prism ◽  
Energy Harvesters ◽  
Amplitude Vibration ◽  
And Behavior

An upstream cylindrical bluff body connected to a tip body via an aluminum cantilever beam was tested as energy harvester in a wind tunnel. The characteristics and behavior of the different tip body configurations and lengths of aluminum cantilever beam were studied to optimize design to extract wind energy. Particular attention was paid to measure vibration amplitude and frequency response as a function of reduced velocity. Dynamic response showed that the device's behavior was dependent on both tip body shape and cantilever beam length. Flow visualization tests showed that high amplitude vibration was obtainable when a vortex was fully formed on each side of the downstream tip body. This was exemplified in a symmetrical triangular prism tip body at L/D1 = 5, where its structure's vibration frequency was close to its natural frequency. At such configuration, electrical energy was captured using a polyvinylidene fluoride (PVDF) piezoelectric beam of different load resistances, where an optimized load resistance could be found for each Reynolds number. Although power output and efficiency obtained were considerably weak when compared to those of traditional wind turbine, the design merits further research to improve its performance under various circumstances.

Piezoelectric wind energy harvester for low-power sensors

2011 ◽  
Vol 22 (18) ◽  
pp. 2215-2228 ◽  
Author(s):  
Jayant Sirohi ◽  
Rohan Mahadik
Keyword(s):  
Energy Harvesting ◽  
Wind Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Load Resistance ◽  
Operating Conditions ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Wireless Sensor Nodes ◽  
Piezoelectric Energy

There has been increasing interest in wireless sensor networks for a variety of outdoor applications including structural health monitoring and environmental monitoring. Replacement of batteries that power the nodes in these networks is maintenance intensive. A wind energy–harvesting device is proposed as an alternate power source for these wireless sensor nodes. The device is based on the galloping of a bar with triangular cross section attached to a cantilever beam. Piezoelectric sheets bonded to the beam convert the mechanical energy into electrical energy. A prototype device of size approximately 160 × 250 mm was fabricated and tested over a range of operating conditions in a wind tunnel, and the power dissipated across a load resistance was measured. A maximum power output of 53 mW was measured at a wind velocity of 11.6 mph. An analytical model incorporating the coupled electromechanical behavior of the piezoelectric sheets and quasi-steady aerodynamics was developed. The model showed good correlation with measurements, and it was concluded that a refined aerodynamic model may need to include apparent mass effects for more accurate predictions. The galloping piezoelectric energy-harvesting device has been shown to be a viable option for powering wireless sensor nodes in outdoor applications.

Energy harvesting from quasi-static deformations via bilaterally constrained strips

2018 ◽  
Vol 29 (18) ◽  
pp. 3572-3581
Author(s):  
Suihan Liu ◽  
Ali Imani Azad ◽  
Rigoberto Burgueño
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Energy Resource ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Power Budget ◽  
Piezoelectric Energy ◽  
Static Conditions

Piezoelectric energy harvesting from ambient vibrations is well studied, but harvesting from quasi-static responses is not yet fully explored. The lack of attention is because quasi-static actions are much slower than the resonance frequency of piezoelectric oscillators to achieve optimal outputs; however, they can be a common mechanical energy resource: from large civil structure deformations to biomechanical motions. The recent advances in bio-micro-electro-mechanical systems and wireless sensor technologies are motivating the study of piezoelectric energy harvesting from quasi-static conditions for low-power budget devices. This article presents a new approach of using quasi-static deformations to generate electrical power through an axially compressed bilaterally constrained strip with an attached piezoelectric layer. A theoretical model was developed to predict the strain distribution of the strip’s buckled configuration for calculating the electrical energy generation. Results from an experimental investigation and finite element simulations are in good agreement with the theoretical study. Test results from a prototyped device showed that a peak output power of 1.33 μW/cm2 was generated, which can adequately provide power supply for low-power budget devices. And a parametric study was also conducted to provide design guidance on selecting the dimensions of a device based on the external embedding structure.

scholarly journals Hollow Piezoelectric Ceramic Fibers for Energy Harvesting Fabrics

2013 ◽  
Vol 8 (1) ◽  
pp. 155892501300800
Author(s):  
François M. Guillot ◽  
Haskell W. Beckham ◽  
Johannes Leisen
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Electrical Energy ◽  
Lead Zirconate ◽  
Ceramic Fibers ◽  
Power Sources ◽  
Electromechanical Performance ◽  
Alternative Power

In the past few years, the growing need for alternative power sources has generated considerable interest in the field of energy harvesting. A particularly exciting possibility within that field is the development of fabrics capable of harnessing mechanical energy and delivering electrical power to sensors and wearable devices. This study presents an evaluation of the electromechanical performance of hollow lead zirconate titanate (PZT) fibers as the basis for the construction of such fabrics. The fibers feature individual polymer claddings surrounding electrodes directly deposited onto both inside and outside ceramic surfaces. This configuration optimizes the amount of electrical energy available by placing the electrodes in direct contact with the surface of the material and by maximizing the active piezoelectric volume. Hollow fibers were electroded, encapsulated in a polymer cladding, poled and characterized in terms of their electromechanical properties. They were then glued to a vibrating cantilever beam equipped with a strain gauge, and their energy harvesting performance was measured. It was found that the fibers generated twice as much energy density as commercial state-of-the-art flexible composite sensors. Finally, the influence of the polymer cladding on the strain transmission to the fiber was evaluated. These fibers have the potential to be woven into fabrics that could harvest mechanical energy from the environment and could eventually be integrated into clothing.

Dielectric Elastomer Energy Harvesting and its Application to Human Walking

2011 ◽  
Author(s):  
Heather Lai ◽  
Chin An Tan ◽  
Yong Xu
Keyword(s):  
Energy Harvesting ◽  
Knee Joint ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
High Energy ◽  
Dielectric Elastomer ◽  
Metabolic Energy ◽  
High Energy Density ◽  
Human Walking ◽  
Wide Range

Human walking requires sophisticated coordination of muscles, tendons, and ligaments working together to provide a constantly changing combination of force, stiffness and damping. In particular, the human knee joint acts as a variable damper, dissipating greater amounts of energy when the knee undergoes large rotational displacements during walking, running or hopping. Typically, this damping results from the dissipation, or loss, of metabolic energy. It has been proven to be possible however; to collect this otherwise wasted energy through the use of electromechanical transducers of several different types which convert mechanical energy to electrical energy. When properly controlled, this type of device not only provides desirable structural damping effects, but the energy generated can be stored for use in a wide range of applications. A novel approach to an energy harvesting knee joint damper is presented using a dielectric elastomer (DE) smart material based electromechanical transducer. Dielectric elastomers are extremely elastic materials with high electrical permittivity which operate based on electrostatic effects. By placing compliant electrodes on either side of a dielectric elastomer film, a specialized capacitor is created, which couples mechanical and electrical energy using induced electrostatic stresses. Dielectric elastomer energy harvesting devices not only have a high energy density, but the material properties are similar to that of human tissue, making it highly suitable for wearable applications. A theoretical framework for dielectric elastomer energy harvesting is presented along with a mapping of the active phases of the energy harvesting to the appropriate phases of the walking stride. Experimental results demonstrating the energy harvesting capability of a DE generator undergoing strains similar to those experienced during walking are provided for the purpose of verifying the theoretical results. The work presented here can be applied to devices for use in rehabilitation of patients with muscular dysfunction and transfemoral prosthesis as well as energy generation for able-bodied wearers.

Optimum Design of Cantilevered Piezoelectric Harvester Based on Distributed Parameter Model

2011 ◽  
Author(s):  
Saad F. Alazemi ◽  
Ahmet S. Yigit ◽  
Khaled A. Alhazza
Keyword(s):  
Power Generation ◽  
Mechanical Energy ◽  
Broad Band ◽  
Average Power ◽  
Electrical Energy ◽  
Distributed Parameter ◽  
Fe Model ◽  
Physical Constraints ◽  
Distributed Parameter Model ◽  
Design Variables

In the past decade, there have been numerous studies which showed the feasibility of harvesting electrical energy from vibrating structures. The main goal of this study is first to generate a Finite Element (FE) model using ANSYS to verify an existing harvesting model. This FEM model can be used as a base for designing more complex harvesters. The second goal of this study is to optimize the parameters of a simple cantilever harvester to maximize the power generation from ambient mechanical energy. A distributed parameter model and its modal solution are used to identify the design variables through a parametric study. The results obtained using the distributed parametric model is compared with the results obtained using ANSYS. It is of interest to ensure adequate power generation under non-resonant conditions for a broad band excitation. The average power within a certain frequency range is used as the cost function to define optimization problem along with some geometric and physical constraints. We found that, in certain frequency ranges, the parameters can be optimized to generate maximum power. Having validated the methodology, work is in progress to design and optimize harvesters with complex geometries.

Multiple Resonances Piezoelectric Energy Harvesting Generator

2009 ◽  
Author(s):  
Shaofan Qi ◽  
Roger Shuttleworth ◽  
S. Olutunde Oyadiji
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Limited Bandwidth ◽  
Piezo Element ◽  
Piezoelectric Energy ◽  
Wide Range ◽  
Environmental Vibration ◽  
Design And Testing

Energy harvesting is the process of converting low level ambient energy into usable electrical energy, so that remote electronic instruments can be powered without the need for batteries or other supplies. Piezoelectric material has the ability to convert mechanical energy into electrical energy, and cantilever type harvesters using this material are being intensely investigated. The typical single cantilever energy harvester design has a limited bandwidth, and is restricted in ability for converting environmental vibration occurring over a wide range of frequencies. A multiple cantilever piezoelectric generator that works over a range of frequencies, yet has only one Piezo element, is being investigated. The design and testing of this novel harvester is described.

scholarly journals The State-of-the-Art Brief Review on Piezoelectric Energy Harvesting from Flow-Induced Vibration

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Hongjun Zhu ◽  
Tao Tang ◽  
Huohai Yang ◽  
Junlei Wang ◽  
Jinze Song ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Wake Flow ◽  
Structural Vibration ◽  
Small Scale ◽  
Flow Induced Vibration ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Self Powered

Flow-induced vibration (FIV) is concerned in a broad range of engineering applications due to its resultant fatigue damage to structures. Nevertheless, such fluid-structure coupling process continuously extracts the kinetic energy from ambient fluid flow, presenting the conversion potential from the mechanical energy to electricity. As the air and water flows are widely encountered in nature, piezoelectric energy harvesters show the advantages in small-scale utilization and self-powered instruments. This paper briefly reviewed the way of energy collection by piezoelectric energy harvesters and the various measures proposed in the literature, which enhance the structural vibration response and hence improve the energy harvesting efficiency. Methods such as irregularity and alteration of cross-section of bluff body, utilization of wake flow and interference, modification and rearrangement of cantilever beams, and introduction of magnetic force are discussed. Finally, some open questions and suggestions are proposed for the future investigation of such renewable energy harvesting mode.

Sign in / Sign up

Export Citation Format

Share Document