scholarly journals An Experimental Investigation of the Progressive Failure of Sandstone and Its Energy Evolution Characteristics

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Yan Chen ◽  
Baohua Guo
Keyword(s):  
Crack Propagation ◽  
Crack Closure ◽  
Progressive Failure ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Energy Evolution ◽  
Evolution Characteristics ◽  
Confining Pressures ◽  
The Relationship

In this research study, the progressive failure and energy evolution characteristics of sandstone samples with different sizes were explored under uniaxial and triaxial compression conditions. The characteristic stresses and strains were captured using the crack axial strain levels and dissipative energy. The results showed that, with the increase in the ratios of the height to diameter (H/D), the crack closure stresses increased, while the crack damage stresses decreased. However, the levels of both the crack closure stresses and crack damages were observed to increase with the H/D. With increase in the confining pressure, it was found that the crack closure and crack damage stresses increased, while their levels decreased. The strains of the crack closures, peak crack axial, and crack propagation were observed to decrease with the H/D, while the crack closure strain levels increased. Also, the crack propagation strains were observed to increase with the confining pressures, while the crack closure, peak crack axial, and crack closure strain levels decreased. The progress failure of the sandstone samples was also obtained based on the evolution characteristics of the dissipative energy. The relationship between the energy densities during each phase and the H/D was also analyzed. It was determined that, with the increasing of the H/D, the input, elastic, and dissipative energy densities displayed different evolution characteristics. Furthermore, with the increases in the characteristic stresses, the input and elastic energy densities were found to increase. The dissipative energy density displayed a slight increase with the increases in the peak strength, which resulted in variations with regard to the crack closures and crack damage stresses.

scholarly journals Energy Evolution Law of Marble Failure Process Under Different Confining Pressures Based on Particle Discrete Element Method

2021 ◽  
Vol 8 ◽  
Author(s):  
Yan-Shuang Yang ◽  
Wei Cheng ◽  
Zhan-Rong Zhang ◽  
Hao-Yuan Tian ◽  
Kai-Yue Li ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Dissipation ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Failure Process ◽  
Rock Failure ◽  
Biaxial Compression ◽  
Energy Evolution ◽  
Confining Pressures ◽  
Energy Dissipated

The energy dissipation usually occurs during rock failure, which can demonstrate the meso failure process of rock in a relatively accurate way. Based on the results of conventional triaxial compression experiments on the Jinping marble, a numerical biaxial compression model was established by PFC2D to observe the development of the micro-cracks and energy evolution during the test, and then the laws of crack propagation, energy dissipation and damage evolution were analyzed. The numerical simulation results indicate that both the crack number and the total energy dissipated during the loading process increase with confining pressures, which is basically consistent with the experiment results. Two damage variables were presented in terms of the density from other researchers’ results and energy dissipation from numerical simulation, respectively. The energy-based damage variable varies with axial strain in the shape of “S,” and approaches one more closely than that based on density at the final failure period. The research in the rock failure from the perspective of energy may further understand the mechanical behavior of rocks.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

scholarly journals Experimental Research into the Evolution of Permeability of Sandstone under Triaxial Compression

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5065
Author(s):  
Liming Zhang ◽  
Shengqun Jiang ◽  
Jin Yu
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Testing Machine ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Rate Of Change ◽  
Peak Strength ◽  
Sudden Increase ◽  
Seepage Pressure ◽  
Confining Pressures

Failure tests on sandstone specimens were conducted under different confining pressures and seepage pressures by using an MTS triaxial rock testing machine to elucidate the corresponding correlations of permeability and characteristic stress with confining pressure and pore pressure during deformation. The results indicate that permeability first decreases and presents two trends, i.e., a V-shaped increase and an S-shaped trend during the non-linear deformation stage. The greater the seepage pressure, the greater the initial permeability and the more obvious the V-shaped trend in the permeability. As the confining pressure was increased, the trend in the permeability gradually changed from V- to S-shaped. Compared with the case at a high confining pressure, the decrease of permeability occurred more quickly, the rate of change becomes greater, and the sudden increase observed in the permeability happened earlier under lower confining pressures. Within the range tested, confining pressure exerted a greater effect on the permeability than the seepage pressure. In comparison with the axial strain, volumetric strain better reflected changes in permeability during compaction and dilation of sandstone. The ratio of crack initiation stress to peak strength ranged from 0.37 to 0.50, while the ratio of dilation stress to peak strength changed from 0.58 to 0.72. Permeabilities calculated based on Darcy and non-Darcy flow changed within the same interval, while the change in permeability was different.

scholarly journals Experimental Study on Viscoplastic Property of Unsaturated Reticulate Red Clay Used as an Engineered Barrier

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Chuang Zhang ◽  
Jian-Zhong Li ◽  
Yong He
Keyword(s):  
Axial Strain ◽  
Confining Pressure ◽  
Matric Suction ◽  
Triaxial Tests ◽  
Red Clay ◽  
Reticulate Red Clay ◽  
Confining Pressures ◽  
Loading Tests ◽  
Engineered Barrier ◽  
The Relationship

In this study, to explore the feasibility of a compacted red clay as an engineered barrier in landfills, the viscoplastic property of remodeled unsaturated reticulate red clay was studied through a series of triaxial tests. According to the deviatoric stress–axial strain curves obtained through loading tests with varying strain rates and under different conditions, the viscoplastic parameter β of remodeled reticulate red clay was obtained. The effects of different matric suctions and net confining pressures on the viscoplasticity of unsaturated reticulate clay were analyzed. The test results showed that remodeled reticulate red clays with different degrees of saturation have similar viscoplastic properties, and their stress–strain curves are all isotach. The stiffness of unsaturated reticulate red clay increased with increasing confining pressure and matric suction. The relationship between β and the net confining pressure can be described using a linear equation. The β value of the specimens increased with increasing matric suction under a constant net confining pressure. A similar linear relationship was observed between β and the matric suction. These relationships are explained considering the loading rate effect mechanism.

scholarly journals The energy evolution characteristics of coal under different dynamic strain rates and confining pressures

2019 ◽  
Vol 23 (3 Part A) ◽  
pp. 1409-1416
Author(s):  
Yi-Qiang Lu ◽  
Xiao-Hui Liu ◽  
Jing Xie ◽  
Zhi-Qiang He ◽  
Cong Li
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Strengthening Effect ◽  
Peak Strain ◽  
Energy Evolution ◽  
Evolution Characteristics ◽  
Confining Pressures

Coal specimens from baijiao coal mine were impacted by a split Hopkinson pressure bar to study its dynamic mechanical behavior under different confining pressures (0-12 MPa) and different strain rates (20-250 s-1). The performances and the energy evolution characteristics of the coal specimens were analyzed. The results show that the strengthening effect and toughening effect of rock are gradually enhanced with the increase of confining pressure. At the same time, the coal failure gradually transitions and develops from tensile failure to compression-shear failure under the action of confining pressure. The peak strength and peak strain of coal rock show significant strain rate correlation and strong confining pressure effect with the change of confining pressures and strain rates. The dynamic strength growth factor of coal is approximately linear with the increasing of strain rates. The energy density and energy absorption density increase linearly with the increase of strain rates, and the energy consumption ratio has a logarithmic growth relationship with the strain rates.

scholarly journals Experimental investigation on creep behavior of clastic rock

2020 ◽  
Vol 165 ◽  
pp. 03051
Author(s):  
Zhang Yu ◽  
Zhang Yan ◽  
Mei Song-hua
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Testing Machine ◽  
Creep Model ◽  
Test Results ◽  
Creep Failure ◽  
Creep Properties ◽  
Clastic Rock ◽  
Confining Pressures ◽  
The Relationship

Many deflected fault zones exist under the dam foundation Xiang-jiaba Hydropower Station in southwestern China. Clastic rock is the main medium with poor physical and mechanical properties. In or-der to study the creep properties of the clastic rock, triaxial compression creep experiments were carried out on a rock servo-controlling rheology testing machine. From the test results, it can be concluded that the clastic rock has obvious creep characteristics, and the time-dependent deformation is large. Based on the test results, the relationship between axial strain and time under different confining pressures is studied. The relationship between axial strain rates and deviatoric stress under different stress levels is also discussed in de-tail. Furthermore, the creep failure mechanism under different confining pressures is analyzed as well. Therefore, the creep law of the clastic rock specimen is gained. The relationship between the Burgers creep model and its parameters is obtained by fitting the creep curve with Burgers creep model. The result shows that Burgers model can accurately describe the creep properties of the clastic rock in Xiang-jiaba Hydro-power Project.

scholarly journals Energy Evolution Characteristics and Distribution Laws of Rock Materials under Triaxial Cyclic Loading and Unloading Compression

2017 ◽  
Vol 2017 ◽  
pp. 1-16 ◽  
Author(s):  
Mingwei Zhang ◽  
Qingbin Meng ◽  
Shengdong Liu
Keyword(s):  
Cyclic Loading ◽  
Energy Density ◽  
Elastic Energy ◽  
Confining Pressure ◽  
Dissipated Energy ◽  
Energy Evolution ◽  
Elastic Energy Density ◽  
Evolution Characteristics ◽  
Storage Limit ◽  
Confining Pressures

To explore the influence of confining pressure on the energy evolution characteristics of loaded rocks, triaxial cyclic loading-unloading experiments on sandstones were carried out under 6 kinds of confining pressures using the axial loading and circumferential deforming control modes. Total energy density, elastic energy density, and dissipated energy density absorbed by rock specimens under different confining pressures were obtained. The confining pressure effect of the evolution process and distribution law in energy accumulation and dissipation was analyzed. Energy conversion mechanism from rock deformation to failure was revealed, and energy conversion equations in different stress-strain stages were established. The method of representing the rock energy accumulation, dissipation, and release behaviors by energy storage limit density, maximum dissipated energy density, and residual elastic energy density was established. The rock showed that, with the increase of confining pressure, the characteristic energy density of rock increased in the power exponent form, and the energy storage limit density increased faster than the maximum dissipated energy density. The greater the confining pressure was, the greater the proportion of elastic energy before peak was. It is indicated that the confining pressure increased the energy inputting intensity, improved the energy accumulating efficiency, and inhibited the energy releasing degree.

scholarly journals Study of statistical damage constitutive model of layered composite rock under triaxial compression

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Yong-Sheng Liu ◽  
Zhuan-Zhuan Qiu ◽  
Xue-Cai Zhan ◽  
Hui-Nan Liu ◽  
Hai-Nan Gong
Keyword(s):  
Constitutive Model ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Layered Composite ◽  
Model Parameters ◽  
Compression Tests ◽  
Fitting Method ◽  
Confining Pressures ◽  
Curve Fitting Method

Abstract The layered composite rock was subjected to triaxial compression tests under constant confining pressure and the stress–strain curves under different confining pressures were obtained. Based on the continuous damage theory and statistical strength theory, it is assumed that the strength of rock microelements obeys Weibull distribution by taking the defects such as random micro-cracks in the rock into account. The statistical constitutive model of layered composite rock with damage correction is established by taking the axial strain of rock as a random distribution variable of microelement strength. The model parameters were determined by the curve fitting method and referring to some test parameters. By comparing the experimental data and the constitutive model curve, the rationality and feasibility of the model are verified.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

Sign in / Sign up

Export Citation Format

Share Document