scholarly journals Flexural Modelling and Finite Element Analysis of FRC Beams Reinforced with PVA and Basalt Fibres and Their Validation

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Tehmina Ayub ◽  
Sadaqat Ullah Khan ◽  
Nasir Shafiq
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Volume Fraction ◽  
Equivalent Stress ◽  
Maximum Load ◽  
Reinforcing Bars ◽  
Stress Strain ◽  
Element Analysis ◽  
Three Point Bending ◽  
Capacity Model

A flexural capacity model for fibre-reinforced concrete (FRC) beams reinforced with PVA and basalt fibres is suggested for the rectangular beam sections. The proposed models are based on the concept of equivalent stress block parameters for both compressive and tensile stresses, similar to Eurocode and ACI code. The parameters are defined by allowing the conversion of the stress-strain models into equivalent rectangular stress blocks, similar to Eurocode 2. The flexural model is suggested to determine the loading capacity of 21 FRC beams containing up to 3% volume fraction of PVA and basalt fibres without reinforcing bars. In order to investigate the accuracy of the proposed flexure models, finite element analysis (FEA) of the same beams was carried out using the compressive and tensile stress-strain curves. Furthermore, 21 FRC beams subjected to three-point bending were tested. The results of the flexural models showed good agreement with the load-carrying capacity of the tested FRC beams, and the results of FEA of all beams showed a good correlation with the experimental results in terms of the maximum load, load versus midspan deflection patterns, and the maximum tensile strains.

Stress Distribution Around Maxillary Anterior Implants as a Factor of Labial Bone Thickness and Occlusal Load Angles: A 3-Dimensional Finite Element Analysis

2014 ◽  
Vol 40 (1) ◽  
pp. 37-42 ◽  
Author(s):  
Marzieh Alikhasi ◽  
Hakimeh Siadat ◽  
Allahyar Geramy ◽  
Ahmad Hassan-Ahangari
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Strain Distribution ◽  
Equivalent Stress ◽  
Stress Strain ◽  
Element Analysis ◽  
Dental Practitioners ◽  
Maximum Equivalent Stress ◽  
Resultant Stress

The purpose of this study was to evaluate the influence of the stress/strain distribution in buccal bone of an anterior maxillary implant using 3 bone thicknesses under 5 different loading angles. Different testing conditions incorporating 3 buccal bone thicknesses, 3 bone compositions, and 5 loading angles of an anterior maxillary implant were applied in order to investigate the resultant stress/strain distribution with finite element analysis. The maximum equivalent stress/strain increased with the decreasing of loading angle relative to the long axis. In addition to loading angle, bone quality and quantity also influenced resultant stress distribution. Dental practitioners should consider combinations of bone composition, diameter, and load angulations to predict success or failure for a given implant length and diameter.

scholarly journals Comparative Analysis of Natural Fibre Reinforced Composite Material Using ANSYS

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
K. G. Saravanan ◽  
R. Prabu ◽  
A. Sivapragasam ◽  
Nahom Daniel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shear Stress ◽  
Equivalent Stress ◽  
Natural Fibre ◽  
Natural Fibres ◽  
Green Composites ◽  
Stress Strain ◽  
Element Analysis ◽  
Fibre Composites

The regulations of legislative bodies regarding the recycling and reusage of automotive materials has caused a great deal of obligation among automotive manufacturers to use natural fibres or green composites. Green composites or more commonly known as bio-composites are made up of natural fibres. Natural fibres are used by humankind since prehistoric times. The natural fibre is obtained from plants as well as animals. Since the natural fibre is obtained from natural as well as biological resources, it is biodegradable and recyclable. This paper presents the study and analysis conducted to address the suitability of natural fibre in the automotive industry. This paper discusses the finite element analysis of four different natural fibre composites used for making car door panel, i.e., flax, jute, sisal, and leather are taken for the material study. This paper helps to find the effectiveness of each of the four natural fibre composites that have already been used in the automotive sector. This paper includes the analysis of four different natural fibres with and without the addition of the aluminium as the reinforcement material. This project revolves around the design of the composite fibre sheet and analysis of the mechanical parameters such as equivalent stress, shear stress, strain, deformation, and so on. The studies and observations of the analysis showed that the natural fibre with the aluminium reinforcement proved to be much stronger than that without the reinforcement. The results of finite element analysis showcased lowest total deformation and equivalent strain in the flax as 1.026 m and 0.017 mm/mm, respectively. However, sisal showed the lowest equivalent stress and shear stress which were 68.09 and 38.178 MPa, respectively. Additionally, leather showed the highest amount of stress, strain, and deformation, and hence leather was deemed to have undesirable properties regarding the usage in car door panels. All the materials except leather were found to be safe under the loading conditions. Hence, the flax fibre is recommended by the project to have superior properties compared to the other materials.

scholarly journals Finite Element Analysis of Stress-Strain Response at the Tool Pin During Friction Stir Process

2015 ◽  
Vol 76 ◽  
pp. 522-527
Author(s):  
M. Shamil Jaffarullah ◽  
Nur’Amirah Busu ◽  
Cheng Yee Low ◽  
J.B. Saedon ◽  
Armansyah ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Response ◽  
Stress Strain ◽  
Element Analysis ◽  
Friction Stir Process ◽  
Friction Stir ◽  
Tool Pin

Optimization design of titanium alloy connecting rod based on structural topology optimization

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Bin Zheng ◽  
Yi Cai ◽  
Kelun Tang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Topology Optimization ◽  
Optimization Design ◽  
Equivalent Stress ◽  
Connecting Rod ◽  
Element Analysis ◽  
Content Type ◽  
The Finite Element Analysis ◽  
Maximum Equivalent Stress

Purpose The purpose of this paper is to realize the lightweight of connecting rod and meet the requirements of low energy consumption and vibration. Based on the structural design of the original connecting rod, the finite element analysis was conducted to reduce the weight and increase the natural frequencies, so as to reduce materials consumption and improve the energy efficiency of internal combustion engine. Design/methodology/approach The finite element analysis, structural optimization design and topology optimization of the connecting rod are applied. Efficient hybrid method is deployed: static and modal analysis; and structure re-design of the connecting rod based on topology optimization. Findings After the optimization of the connecting rod, the weight is reduced from 1.7907 to 1.4875 kg, with a reduction of 16.93%. The maximum equivalent stress of the optimized connecting rod is 183.97 MPa and that of the original structure is 217.18 MPa, with the reduction of 15.62%. The first, second and third natural frequencies of the optimized connecting rod are increased by 8.89%, 8.85% and 11.09%, respectively. Through the finite element analysis and based on the lightweight, the maximum equivalent stress is reduced and the low-order natural frequency is increased. Originality/value This paper presents an optimization method on the connecting rod structure. Based on the statics and modal analysis of the connecting rod and combined with the topology optimization, the size of the connecting rod is improved, and the static and dynamic characteristics of the optimized connecting rod are improved.

Study on Cylindrical Heatsink Forging Process Considering Friction Condition

2019 ◽  
Vol 823 ◽  
pp. 141-144
Author(s):  
Tung Sheng Yang ◽  
Yong Nan Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Factor ◽  
Testing Machine ◽  
Metal Flow ◽  
Compression Tests ◽  
Stress Strain ◽  
Element Analysis ◽  
Forging Process ◽  
Different Temperatures

The feasibility of forging of AL-1050 alloy of cylindrical heatsink under warm conditions is demonstrated in the present work. The stress-strain curves and friction factor play an important role in the cylindrical heatsink forging. The purpose of forging lubrication is to reduce friction between blank and die, and to decrease resistance of metal flow to die. The stress-strain curves at different temperatures are obtained by compressing tests. The friction factor between 1050 aluminum alloy and die material are determined at different temperatures by ring compression tests with graphite lubricants. The compressing and ring compressing tests are carried out by using the computerized screw universal testing machine. The finite element method is used to investigate the forming characters of the forging process. To verify the prediction of FEM simulation in the cylindrical heatsink forging process, the experimental parameters such as stress-strain curves and fiction factor, are as the input data during analysis. Maximum forging load and effective stress distribution are determined of the heatsink forging, using the finite element analysis. Finally, the cylindrical heatsink parts are formed by the forging machine under the conditions using finite element analysis.

Finite element analysis of stress–strain localization and distribution in Al-4.5Cu-2Mg alloy

2018 ◽  
Vol 28 (6) ◽  
pp. 1200-1215 ◽  
Author(s):  
Rahul BHANDARI ◽  
Prosanta BISWAS ◽  
Manas Kumar MONDAL ◽  
Durbadal MANDAL
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Localization ◽  
Stress Strain ◽  
Element Analysis
Sign in / Sign up

Export Citation Format

Share Document